Vivint VS-PANIC3-345 User manual

T
he Vivint Emergency Pendant (PANIC3) is designed to
transmit an emergency signal
from any location
within range
of the
control panel. The panel will receive signals whether
the system is armed or disarmed.
The PANIC
3 device is discrete, versatile, and is small and
lightweight
enough to be stored in a pocket or purse.
Additionally, t
he supplied lanyard allows the pendant to be
worn around the neck or wrist.
4931 N 300 W Provo, UT 84604
Quick Reference
Programming Instructions
•The PANIC3 Emergency Pendant device can be programmed as a supervised or non-supervised device.
If supervised, the device should always stay within range of the panel.
•The device can be programmed to contact emergency services with either an audible or silent alarm.
Emergency Pendant
(VS-PANIC3-345)
PRINT INSTRUCTIONS:
REFERENCE SHEET VS-PANIC3-345 P/N 77-600050-001 REV 1.0 |
INK: BLACK | MATERIAL: 20 LB MEAD BOND | SIZE:5.50" X8.50" SCALE 1:1 |
FOLDS: TRI-FOLD VERTICAL, TRI-FOLD HORIZONTAL (TO FITIN BOX)
Installer Test
Press and hold the button for 2 seconds to send signals from the device to the control panel.
Standards Certifications & Listings
UL 1023
Standard for Household Burglar-
Alarm System Units
CAN/ULC-S304
Standard for Control Units,
Accessories and Receiving Equip-
ment for Intrusion Alarm Systems
FCC ID:
2AAAS-PB01
IC:
10941A-PB01
*For complete regulatory compliance
i
nformation, go to: vivint.com/fcc.
Technical / Hardware Specifications
Vivint Part Number (P/N)
VS-PANIC3-345
Model Number (M/N)
PB01
Wireless Signal Range
300 ft (91.4 m), open air (1)
Battery
Panasonic CR2032 or equiv-
alent lithium battery (2)
Battery Life
3-5 years normal usage (1)
Transmitter Frequency
345 MHz
Code Outputs
Alarm, Alarm Restore,
Supervisory, Low Battery
Supervisory Interval
70 minutes per signal (12
hours for panel to report
supervision failure)
Operating Temp. Limits
32° to 120°F (0° to 49°C)
Relative Humidity
5-95% Non-Condensing
Accessories
Use the supplied lanyard accessory to carry the PANIC3 device.
(1) Not evaluated by UL.
(2) Tested with Eve energy, type CR
2032.

Battery Installation
The battery should last 3
-5 years under normal use. If the battery is low, a low
battery
notification will be indicated on the control panel. To replace the battery,
1. Remove the cover by inserting a coin in the slot and twisting gently.
2. Place a small flathead screwdriver in the slot between the metal clip
and battery and pry the battery up and out of the battery holder.
3. Insert the replacement battery with the + sign facing out.*
4. Replace the cover.
5. Verify the device is functioning properly.
*The battery may fit loosely in the holder, but the cover will secure it firmly in place.
FCC and ISED Canada Regulatory Compliance Declarations*
CAUTION:
Unauthorized changes or modifications could void the user’s authority to operate the equipment.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rule
s and Industry Canada (IC)
license
-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation of the device.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This e
quipment generates, uses,
and can radiate radio frequency energy and
, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipme
nt does cause harmful
interference to radio or televis
ion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/television technician for help.
PRUDENCE
:Changements ou modifications pourraient annuler le droit de l'utilisateur à utiliser l'équipement non autorisées.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal
(ou inférieur) approuvé pour l'
émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres
utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.
) ne dépasse pas l'intensité
nécessaire à l'établissement d'une communication satisfaisante.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions
suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillag
e radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Ces limites sont conçues pour fournir une protection raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet équipement
génère, utilise et peut émettre une énergie de radiofréquence et, s'il n'est pas installé et utilisé conformément aux instruc
tions, il peut causer des
interférences nuisibles aux communications radio. Cependant, il n'existe aucune garantie que des interférences no se produiro
nt pas dans une
installation particulière. Si cet équipement provoque des interférences nuisibles à la réception rad
io ou télévision, ce qui peut être déterminé en
mettant l'équipement hors et sous tension, l'utilisateur est encouragé à essayer de corriger l'interférence par une ou plusieurs des mesures suivantes:
•Réorienter ou déplacer l'antenne de réception.
•Augmentez la distance entre l'équipement et le récepteur.
•Connecter l'équipement à une sortie sur un circuit différent de celui sur lequel le récepteur est branché.
•Consulter le revendeur ou un technicien radio / télévision expérimenté pour de l'aide.
Wireless Product Notice
Wireless communications hardware provides reliable communication; however, there are
limitations which must be observed.
•The transmitters are required to comply with all applicable wireless rules and regulations. As such, they have limited
transmitter power and limited range.
•Wireless signals may be blocked by radio signals that occur on or near the wireless operating frequencies.
© 2022 Vivint Inc. All Rights Reserved. | www.vivint.com | M/N: PB01 | Doc P/N: 77-600050-001 Rev. 1.0
WARNING! The polarity of the battery must be observed (as shown in the image). Improper
handling of lithium batteries may result in heat generation, explosion, or fire, which may lead to
personal injury. Replace only with the same or equivalent battery type as recommended by the manufacturer.
AVERTISSEMENT! La polarité de la batterie doit être observée (comme indiqué dans l'image). Une mauvaise manipulation des piles
au lithium peut conduire à la production de chaleur, une explosion ou un incendie, ce qui peut entraîner des blessures. Remplacez-le
par le même type ou équivalent de la batterie tel que recommandé par le fabricant.
Batteries must not be recharged, disassembled or disposed of in fire.
Disposal of used batteries must be made in accordance with the waste
recovery and recycling regulations in your area.
Keep away from small children
. If batteries are swallowed, promptly see a doctor.
California Only:
This Perchlorate warning applies ONLY to Manganese Dioxide Lithium cells sold or distributed in California, USA. Perchlorate material
special handling may apply.
(For more information, visit: www.dtsc.ca.gov/hazardouswaste/perchlorate)