Vivitar DC-1012 User manual

DC-1012
USER’S MANUAL
RECHARGEABLE
BATTERY
WIRELESS
ALARM
CLOCK
SNOOZE
BUTTON
Bluetooth Speaker with calendar

Important Safety Precautions
When using your Vivitar Bluetooth Speaker Clock, basic safety precautions should always be followed, including
the following:
1. READ ALL INSTRUCTIONS BEFORE USING YOUR SPEAKER.
2. Do not use your speaker near water. Clean using a soft cloth or paper towel.
3. Do not place your speaker on any wet surfaces.
4. Do not allow children or the infirm to play with your speaker without adult supervision.
5. Do not expose your speaker to excessive heat, flames or fire.
6. Always press all buttons or switches carefully. Do not manhandle your speaker.
7. Do not use in extremely dry environments, as this can lead to static discharge during usage.
8. Do not expose your speaker to temperatures above 40°C. Keep out of direct sunlight.
9. Do not attempt to repair this product yourself. Contact a qualified service center if your speaker is in need of
service.
10. Do not drop, puncture or expose your speaker to excessive trauma.
11. Your speaker is not intended for commercial use.
12. Do not place near objects that generate a strong magnetic field.
13. Unplug this device when not in use for long periods of time or during lightning storms.
BATTERY WARNING:
-The device is equipped with an integrated lithium ion battery. The
battery cannot be replaced. Do not attempt to remove the battery
from the device.
-Do not dispose of in fire or expose to excessive heat.
-Do not crush, puncture, incinerate, or short circuit external contacts.
-Please recycle or dispose of the battery properly. Contact your local
recycling facilities and/or the manufacturer for further information.
CAUTION

Introduction
Thank you for purchasing your Vivitar Bluetooth Speaker Clock, item V60030BT. You can use
your speaker with iPads, iPhones, iPods and many other types of smartphones and Bluetooth
devices to stream music. In order to get the best results when using this device, please read this
manual first before using.
Package Contents
-Vivitar V60030BT Bluetooth Speaker Clock
-Micro USB Charging Cable
-User’s Manual with Warranty Information
Specifications
Bluetooth Version: V3.0+EDR
Charging Voltage: DC 5V
Battery Type: Rechargeable 1,200mAh Lithium Ion Battery
Charge Time: Approximately 3 Hours
Frequency Response Range: 80Hz-20KHz;
Speaker: φ40mm/4Ω/3W
Working Voltage: DC 3.7V
Play Time: Up to 4 Hours

A Quick Look at Your Device
Front View
Rear View
DOWN
LED
Indicator
Light
ON/OFF
Switch
Micro USB
Charging Port
UP
SET
MODE

Charging Your Speaker
Your speaker has a built-in, rechargeable lithium ion battery. To avoid damage, do not attempt to
remove the battery. The full performance of the battery is only achieved after a few charging-dis-
charging cycles. Charge the battery fully before first use. To do so, follow the steps below:
1. Connect one end of the included micro USB charging cable to the Micro USB Charging Port on
the rear of your speaker. Then plug the other end of the micro USB charging cable into a USB
port on your computer or a suitable power adapter in order to recharge the internal rechargeable
battery.
NOTE: The internal battery of your speaker takes approximately three hours to charge when
completely drained.
2. When the battery is charging, the LED Indicator Light will turn red. The LED Indicator Light will
turn off when the battery is fully charged. Unplug when charging is complete.
NOTE: Overcharging could reduce the life of the battery. A charged battery will lose its capacity
if it is not used on a regular basis.
Important!
To avoid a complete discharge of the battery, charge your speaker at least once every six
months.

Pairing Your Speaker with a Bluetooth Device
Your speaker can be paired with most Bluetooth devices including iPads, iPhones, iPod Touches,
and most smartphones, laptops and tablets. In order to pair your speaker with a phone, follow the
steps below:
1. Slide the On/Off Switch to the ON position in order to turn on your speaker. The LED Indicator
Light will start alternately flashing red and then blue repeatedly. This indicates that your earbuds
are in pairing mode.
2. Go to the Bluetooth Manager of your Bluetooth device.
3. Search Bluetooth devices and select “Vivitar BT clock” to start connecting.
4. Enter “0000” if your device asks for the PIN code.
5. Once paired, the LED Indicator Light will stop blinking and steadily shine blue. Note that
anytime music is playing, the light will slowly blink blue every few seconds.

Using Your Speaker: Listening to Music
Powering Your Speaker On and OFF
1. Slide the On/Off Switch to the ON position in order to power on your speaker. If you have
already paired your speaker to your Bluetooth device, they will automatically remain paired each
time you power on your speaker.
2. Slide the On/Off Switch to the OFF position in order to power off your speaker.
Listening to Music
• Button: Press to play or pause a track.
• Quickly tap the “ ” button to advance to the next song in a playlist.
• Quickly tap the “ ” button to go back to the previous song in a playlist.
• Press and hold the “ ” button to increase the volume.
• Press and hold the “ ” button to decrease the volume.
Note: You can also adjust volume and playback settings on your phone or connected audio
device.

Using Your Speaker: Setting the Date & Time
1. Press the MODE button repeatedly until the symbol “TIME” is displayed in the upper right hand
corner of the display screen.
2. Press the SET button to enter the date and time settings mode.
3. Press the DOWN or UP buttons to increase or decrease a setting. Press the SET button to
confirm a setting and move to the next setting.
4. In the date and time settings mode you can adjust the hour, minute, year, month and day.
.

Using Your Speaker: Setting the Alarm Clock
1. Press the MODE button repeatedly until the symbol “AL” is displayed in the upper right hand
corner of the display screen.
2. Press the SET button to enter the alarm setting mode.
3. Press the DOWN or UP buttons to increase or decrease a setting. Press the SET button to
confirm a setting and move to the next setting.
4. In the alarm settings mode you can adjust the alarm time (hour and minute), snooze interval (1
to 60 minutes), and alarm sound (choose among 7 tones).
.

Using Your Speaker: Turning the Alarm On
1. Press the MODE button repeatedly until the symbol “AL” is displayed in the upper right hand
corner of the display screen.
2. Press the DOWN and UP buttons repeatedly to choose between turning on the alarm ( ) by
itself, or turning it on with snooze ( and ) or turning it off.
3. To stop the alarm from going off, press either the MODE, DOWN, or UP buttons.
4. Unless stopped, the snooze function will remain on until it has rung 4 times.