Vivitek LT30C-F User manual

Model:LT30C-F

Important Safety
Checking The Supplied Accessories
*
Wall Plate X 1
Fixed Support Arm X 1
Projector Mounting Plate X 1
B
NO
C
D
E
A
5
5
1
4
F
Screw(M6X55)
Φ10mm Anchor bolt
L5 Allen key
4
Screw(M4X10)
diagrammatic
presentation
designation
quantity
1
L3 Allen key
Screw(M6X15)
Wall Plate Cover X 1
2
3
4
5
7
8
9
Pg.2
GM4 connecting
screw
4
Projection screen
V-Offset
Wall plate
Projection screen
Bottom of
mounting plate
Top of image V-Offset
Wall plate must be aligned to center of screen
L1
L2
Wall Cover X 1

Checking The Installation Position
Pg.3
From a projecting surface
to the rear of the unit L1
cm x cm
105
125
Diagonal Width x Height Bottom height
(V-Offset)
inch
80
150
177 x 99.6
232 x 130
277 x 156
332 x 187
inch (cm)
11.1(28.2)
13.4(34)
15.23(38.7)
17.53(44.5)
From a projecting surface
to the rear of the unit L2
Projection image size Installation distance
1.63(4.1)
6.87(17.5)
11.06(28.1)
16.3(41.4)
16.98(43.1)
22.22(56.5)
26.42(67.1)
31.65(80.4)
1080P [1920 x 1080]
From a projecting surface
to the rear of the unit L1
cm x cm
105
125
Diagonal Width x Height
inch
80
150
172 x 108
226 x 141
269 x 168
323x 202
inch (cm)
101.05(256.7)
120.9(307.1)
136.78(347.4)
156.62(397.8)
From a projecting surface
to the rear of the unit L2
Projection image size Installation distance
20.15(51.2)
73.67(187.1)
116.49(295.9)
169.99(431.8)
173.69(441.2)
227.22(577.1)
270.03(685.9)
323.53(821.8)
WXGA [1280 x 800]
From a projecting surface
to the rear of the unit L1
cm x cm
80
105
Diagonal Width x Height
inch
65
125
132 x 99
163 x 120
213 x 160
254x 191
inch (cm)
106.49(270.5)
122.4(310.9)
148.9(378.2)
170.1(432.1)
From a projecting surface
to the rear of the unit L2
Projection image size Installation distance
13.02(33.1)
50.88(129.2)
113.95(289.4)
161.41(417.6)
166.57(423.1)
204.42(519.2)
267.50(679.4)
317.95(807.6)
XGA [1024x768]
To Set The Projector Wall Mount On The Wall
1080P(1920x1080)
Bottom height
(V-Offset)
Bottom height
(V-Offset)

>55mm
ø10~11mm B
Concrete wall mounting
Use anchor bolt
>55mm
ø3mm
Wood stud wall Not use anchor bolt
Loosen the screws with L3 allen wrench,
pull out the support arm around 4'' (100mm)
and make power cable & signal cables go
through the support arm.
Pg.4
Take off the cap
Loosen the screw
D
The cables The cables
The cables
CF
The cables can be got through the wall plate
by three ways as shown in the pictures. Then,
Lock the screw “F” , but not tighten it.
Note : You have to push the arm outward about
3mm before it can be installed.
● The bracket is suitable for concrete wall mounting or wooden stud wall or calcium silicate board(screws M6x55
● Concrete wall mounting thickness must be a minimum 4'' ,Anchor bolt and screw (M6 x55) are needed to be used for concrete wall installation.
● ood stud wall and gypsum board thickness not W must be a minimum 20x12 inch, Stud thickness must be a minimum 3'' . greater than 3/8 inch
If the wall is not strong enough reinforce it sufficiently before installation.
● Please contact if you have any questions about mounting surface issue. manufacturer
● All of the fastening screws provided have to be used 。
● Calcium silicate board mounting, screws M6x55 must be attached to the stud and securely fastened.
screw (M6 × 55) and anchor bolts are needed
for concrete wall mounting.
C
A
The arrows up
Only screw (M6 × 55) are needed
for wood stud wall or calcium silicate board mounting.
C
A
The arrows up
C
A
For wood stud or calcium
silicate board mounting,
screws M6x55 must be
attached onto the center of
stud and securely fastened.
The arrows up
Or
These four screws must be
fastened on the stud.
These two screws must be
fastened on the stud.
must be attached to the stud and securely fastened。

To Install The Projector On The Projector Wall Mount
A
A
B
B
Screen Adjustment Direction
● You can adjust the projector upward/
-downward according to your need.
● Tighten the screw “F” after locating
the projector position.
CF
● Move the projector mounting plate leftwards/rightwards to determine the projector position.
Pg.5
Sliding distance of
adjusting the projector
upward/downward:
3.15''(80mm)
A
B
Leftward/Rightward
sliding distance
E
G
If the surface is not at,
pls use the “G” to avoid
interference.

Tighten the screws Connect power cable and other signal
cable to projector
To Install The Projector On The Projector Wall Mount
A
B
Screen Adjustment Direction
B
A
Note: To make adjustments to meet your demands, screws must be loosened in a specific
order. (When the length of the inside arm does not meet your requirements, then you should
loosen the screws on the outside arm to adjust the middle arm. Under this circumstance, the
number read on the middle arm is correct).
To Adjust The Projector Forwards/Backwards
Pg.6
Power cable
and signal cable
290mm
260mm
200mm
13in
12in
11in
10in
9in
8in
230mm 320mm
360mm
14in 15in
390mm 420mm
16in 17in
290mm
13in
12in
320mm
360mm
14in
420mm
16in 17in
D
B
A
Check the scaleplate
to see the distance from
mounting plate to the wall.

AB
AB
AB
Screen Adjustment Direction
A
Screen
Adjustment
Direction
B
A
B
A
B
Screen Adjustment Direction
To Adjust The Vertical Tilt Knob
To Adjust The Projector Upwards/Downwards
To Adjust The Horizontal Roll Knob
Adjustment Knob
Adjustment Knob
Pg.7
CF

41L3603-EN-MC
LT30C-F
11.46 lbs(5.2kg)Product Weight
12.8" ( 325mm ) - 29.1" ( 740mm )