Vivitek WM-3Z User manual

Installation Manual
It is imperative that the installation instructions within this manual are followed for
safety reasons. Vivitek Corporation is not responsible for damages resulting from
incorrectly installed mounts or projectors on to the mount.
Sufficient expertise is required for installing this projector wall mount.
Do not use the projector wall mount for purposes other than for which it is designed.
Please contact Vivitek at 1-855-885-2378 with any questions pertaining to the correct
installation of this projector mount.
46101 FREMONT BLVD, FREMONT, CA. 94538 - TEL [phone] - EMAIL: - [e-mail]
Model: WM-3Z and LT30B-G
·
·
·
··

Important Safety
Checking The Supplied Accessories
*
Wall Plate X 1
Fixed Support Arm X 1
Projector Mounting Plate X 1
B
NO
C
D
E
A
5
5
1
4
F
Screw(M6X55)
Φ10mm Anchor bolt
L5 Allen key
4
Screw(
diagrammatic
presentation
designation
quantity
1
L3 Allen key
Screw(M6X12)
Wall Plate Cover X 1
2
3
4
5
7
8
9
Pg.2
GM4 connecting
screw
4
Projection screen
V-Offset
Wall plate
Projection screen
Bottom of
mounting plate
Top of image V-Offset
Wall plate must be aligned to center of screen
L1
L2
Wall Cover X 1
M4X10)

Checking The Installation Position
Pg.3
L1 (From Screen surface to
the rear of the projector)
inch (cm)
105" (267)
125" (318)
Diagonal(D)
inch (cm)
80" (203)
150" (381)
70"x 39" (177 x 99)
92" x 52" (232 x 130)
109" x 61" (277 x 156)
131" x 74" (332 x 187)
inch (cm)
11.1" (28.2)
13.4" (34)
15.2" (38.6)
17.5" (44.5)
Projection image size Installation distance
1.63" (4.14)
6.87" (17.5)
11.06" (28.1)
16.98" (43.13)
22.22" (56.44)
26.42" (67.11)
31.65" (80.39)
To Set The Projector Wall Mount On The Wall
1080P(1920x1080)
Vertical Offset
(V-Offset)
Width x Height
Note: 1080p Vertical Offset (V-Offset) can be calculated for different screen sizes beside the four
above. The formula is; V-Offset= [screen width/2 (0.29)]
inch (cm)
105" (267)
125" (318)
Diagonal(D)
inch (cm)
80" (203)
150" (381)
68"x 42" (172 x 108)
89" x 57" (226 x 141)
106" x 66" (269 x 168)
128" x 80" (323 x 202)
inch (cm)
10.0" (25.5)
12.0" (30.5)
13.6" (34.6)
15.6" (39.6)
Projection image size Installation distance
1.63" (4.14)
6.87" (17.5)
11.06" (28.1)
16.3" (41.4)
16.98" (43.13)
22.22" (56.44)
26.42" (67.11)
31.65" (80.39)
Vertical Offset
(V-Offset)
Width x Height
Note: WXGA Vertical Offset (V-Offset) can be calculated for different screen sizes beside the four
above. The formula is; V-Offset= [screen width/2 (0.27)]
L2 (From Screen surface to
the rear of the projector)
L1 (From Screen surface to
the rear of the projector)
L2 (From Screen surface to
the rear of the projector)
inch (cm)
inch (cm)
16.30" (41.4)
1080p (DH765Z-UST & DH768Z-UST)
WXGA (DH763Z-UST)

● The bracket is suitable for concrete wall mounting or wooden stud wall.
● Concrete wall mounting thickness must be a minimum 4'' (100mm). Anchor bolt and screw (M6 × 55) are
needed to be used for concrete wall installation.
● Dry-wall wall thickness must be a minimum 4.5" (114mm). Only screw(M6 × 55) is needed to be used for
installation, and gypsum board thickness less than 0.59" (15mm).
If the wall is not strong enough, reinforce it sufficiently before installation.
● Please contact reseller if you have any questions
about mounting surface issue.
>55mm
ø10~11mm B
Concrete wall mounting
Use anchor bolt
>55mm
ø3mm
Dry-wall mounting Not use anchor bolt
When installation on the
wood stud wall, Align the
center of the wall mount
plate with the center of
the stud. screw central point
Loosen the screws with L3 allen wrench,
pull out the support arm around 4'' (100mm)
and make power cable & signal cables go
through the support arm.
The cables can be got through the wall plate
by three ways as shown in the pictures. Then,
Lock the screw “F” , but not tighten it.
screw (M6 × 55) are needed
for installation in concrete wall mounting
screw (M6 × 55) are needed
for installation in dry-wall mounting
Pg.4
C
A
C
A
Take off the cap
Loosen the screw
D
CF
The arrows up The arrows up
The cables
The cables
The cables

To Install The Projector On The Projector Wall Mount
A
A
B
B
Screen Adjustment Direction
● You can adjust the projector upward/
-downward according to your need.
● Tighten the screw “F” after locating
the projector position.
CF
● Move the projector mounting plate leftwards/rightwards to determine the projector position.
Pg.5
Sliding distance of
adjusting the projector
upward/downward:
3.15''(80mm)
A
B
Leftward/Rightward
sliding distance
E
G
If the surface is not at,
pls use the “G” to avoid
interference.

Tighten the screws Connect power cable and other signal
cable to projector
To Install The Projector On The Projector Wall Mount
A
B
Screen Adjustment Direction
B
A
Note: To make adjustments to meet your demands, screws must be loosened in a specific
order. (When the length of the inside arm does not meet your requirements, then you should
loosen the screws on the outside arm to adjust the middle arm. Under this circumstance, the
number read on the middle arm is correct).
To Adjust The Projector Forwards/Backwards
Pg.6
Power cable
and signal cable
290mm
260mm
200mm
13in
12in
11in
10in
9in
8in
230mm 320mm
360mm
14in 15in
390mm 420mm
16in 17in
290mm
13in
12in
320mm
360mm
14in
420mm
16in 17in
D
B
A
Check the scaleplate
to see the distance from
mounting plate to the wall.

AB
AB
AB
Screen Adjustment Direction
A
Screen
Adjustment
Direction
B
A
B
A
B
Screen Adjustment Direction
To Adjust The Vertical Tilt Knob
To Adjust The Projector Upwards/Downwards
To Adjust The Horizontal Roll Knob
Adjustment Knob
Adjustment Knob
Pg.7
CF

Product Information
:
AB
A
B
Screen Adjustment Direction
Note: When all adjustments are completed, the wall plate covers can be used to cover the
blank area on the top of wall plate. The number of wall plate covers used depends on the
size of the blank area. But the wall cover must be used in an specific order as the picture
on the left shows. Finally, put the wall cover on.
To Place The Decorative Cover Knob
To Adjust The Horizontal Rotation Knob
Adjustment Knob
or
1
1
2
1
2
3
Wall Plate cover
1
2
3
4
Model LT30B-G WM-3Z
Product Weight 9.9lbs (4.5kg) 12.13lbs (5.5kg)
Load Capacity 33lbs (15kg) 33lbs (15kg)
Adjustable
Range
8.7” (225mm) - 19.5” (495mm)
(from mounting plate center to screen)
12.8” (325.1mm) - 29.13” (740mm)
(from mounting plate center to screen)
Adjustable Angle ± 5° tilt, left/right, front/rear and lateral
rotation adjustment
± 5° tilt, left/right, front/rear and lateral
rotation adjustment