Vivo STAND-V003V User manual

Triple Vertical Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v003v
SKU: STAND-V003V
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
a (x1)
Pole
b(x1)
Clamp
c(x1)
Clamp Brace
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
d(x3)
Monitor Arm
e (x3)
VESA Plate
f (x3)
M4x6
g (x3)
M5x14
h (x2)
M8x12
i (x1)
M10 Bolt
j(x1)
Support Plate
k (x1)
M10 Washer
l (x1)
Spring Washer
m (x1)
Grommet Base
Plate
n(x3)
Wire Clip
o(x1)
Allen Key
p (x1)
Wrench
q (x12)
M4x12
Thumbscrew
r (x12)
M4x30
s (x12)
M4 Spacer
t1 (x1)
So Pad
t2 (x1)
So Pad
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
ASSEMBLY STEPS
TOOLS NEEDED
Phillips
Screwdriver
PRE-ASSEMBLY
Remove the grub screws by provided Allen Key (o). Connect the poles by threads as below diagram.
Install the grub screws and fasten them by provided Allen Key (o).
STEP 1
OPTION A: Clamp Installation
1. Install the “C” Clamp Brace (c) to the Pole
(a) using 3pcs M5x14 Bolts (g), and tighten
using the Allen Key (o),see Figure 1.
2. Attach So Pad (t1) to the “C” Clamp Brace
(c), see Figure 2.
3. Install the “C” Clamp (b) to the pole
assembly according to the thickness of the
desktop. The thickness can be changed
to three positions. Connect it using 2pcs
M8x12 Bolts (h), and tighten using the
Allen Key (o). Tighten the “C” Clamp to
the desktop using the plastic knob, see
Figure 3.
33 lbs
(15 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
Drill

4
STEP 1 (Continued)
OPTION B: Existing Grommet Base Installation
If the existing grommet hole comes with a plastic
protector, remove it to ensure a flat surface before
installing the desk mount.
1. Install the Grommet Base Plate (m) to the
Pole (a) using 3pcs M5x14 Bolts (g), and
tighten using the Allen Key (o), see Figure 4.
2. Attach So Pad (t2) to the Grommet Base
Plate (m), see Figure 5.
3. Position the Pole (a) on the mounting surface
and secure using the Support Plate (j),
M10 Washer (k), Spring Washer (l) and M10
Bolt (i). Fasten the M10 Bolt using provided
Wrench (p), see Figure 6.
OPTION C: Self-Drilled Grommet Base Installation
1. Position the Pole (a) on the mounting surface and mark the center hole. Drill a 3/8” (10mm)
diameter hole at the marked position through the mounting surface. Install the Grommet Base
Plate (m) to the Pole (a) using 3pcs M5x14 Bolts (g), and tighten using the Allen Key (o), see
Figure 7.
2. Attach So Pad (t2) to the Grommet Base Plate (m), see Figure 8.
3. Position the Pole (a) on the mounting surface and secure using the Support Plate (j), M10 Washer
(k), Spring Washer (l) and M10 Bolt (i). Fasten the M10 Bolt using provided Wrench (p), see Figure
9.

5
STEP 2
Install Monitor Arm (d) to the Pole (a). Fasten the bolt with supplied Allen Key (o). Attach the Wire
Clip (n) to the pole (a).
STEP 3
OPTION A: Flat Back Monitor
OPTION B: Curved Back Monitor
d
o
n
q
s
r
For flat back monitor, install VESA Plate (e) to
monitor using thumbscrews (q).
For curved back monitor, install VESA Plate (e)
to monitor using bolts (r) and spacers (s).

6
STEP 4
Slide the monitor onto the head of Monitor Arm (d) as shown in the above diagram.
Install the M4x6 Bolt (f). Make sure the bolt is installed before you rotate the monitor.
f

7
STEP 5
Fasten the grub screw in Monitor Arm to fix the tilting angle by provided Allen Key (o). Manage the
wires as shown in the diagram below.
grub
scre w

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303