Vivo STAND-MIC02 User manual

Premium Microphone Boom Arm Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-mic02
SKU: STAND-MIC02
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
.22-2.2lbs
(.1-1kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
TOOLS NEEDED
Phillips
Screwdriver
A (x1)
Arm
B(x1)
Clamp
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
C (x1)
Ball Joint
E (x1)
Grommet Plate
D (x1)
Plastic CoverD)
F (x1)
So Pad
T-A (x1)
3mm Allen
Wrench
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

3
ASSEMBLY STEPS
STEP 1
Clamp Installation
Loosen the knob on Clamp (B).
Remove adhesive backing from
So Pad (F) on place on the under-
side of Clamp (B).
B
B
B2
B
B1
T-A
F
B
Secure Clamp (B) to desktop by tightening
the knob.
B
Grommet Installation
Loosen the knob on Clamp (B). Disassemble
Clamp (B) by removing Clamp Screws (B1),
separating Pole Base (B2) from Clamp (B) using
3mm Allen Wrench (T-A).
Use a Phillips screwdriver to separate Hand Bolt
(B3) and Clamp Plate (B4) from Clamp (B).
B
B4
B3
B1
T-A
F
Connect Grommet Plate (E) to Pole Base (B2)
using Clamp Screws (B1) and 3mm Allen
Wrench (T-A). Remove adhesive backing
from So Pad (F) on place on the underside of
Grommet Plate (E).
B2
E

4
STEP 1 - Continued
STEP 2
Grommet Installation - Continued
If your desktop does not have an existing grommet hole, pre-drill a hole using a drill and a 3/8”
(10mm) drill bit.
Clasp both sides of Arm (A) and squeeze tightly together. Have a second person cut the zip tie. Slowly
release the pressure and unfold Arm.
Insert Hand Bolt (B3) with Plate (B4) through
grommet hole and secure to Pole Base (B1) by
tightening Hand Bolt. B2
A
B4
B3

5
AT-A B
STEP 3
Loosen set screw on Clamp (B) using 3mm Allen Wrench (T-A) and insert Arm (A). Tighten set screw
on Clamp (B) to secure and increase the rotation resistance.
#1
#2
STEP 4
Separate Ball Joint (C) by loosening Knob (C1). Remove Screw (C2) and Ball (C3) from Outer Casing
(C4).
Reassemble Ball Joint (C) onto Arm (A) by securing Ball (C3) and Outer Casing (C4) using Screw (C2)
and Knob (C1).
C1
C1
C2
C2
C3
C3
C4
C4
C4
C4

6
STEP 5
Secure microphone to Ball Joint (C). Slide cable management tabs o Arm (A) to neatly route cable.
Reattach by sliding back into place. NOTE: Please do note attempt to pry tabs o; tabs may snap
or break if too much force is applied.
A
C

7
STEP 6
STEP 6
To adjust microphone position, loosen Knob (C1) on Ball Joint (C) and adjust positioning. Retighten
Knob (C1) to secure.
Adjust tension of Arm (A) using 3mm Allen Wrench (T-A). Place Plastic Cover (D) over joint in Arm (A).
C1
D
AT-A
C

LAST UPDATED: 10/10/2022
REV2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303