Vivo MOUNT-DLMM1 User manual

Mount Designed for Dell OptiPlex Micro
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-dlmm1
SKU: MOUNT-DLMM1
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual
and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly, or inappropriate use.
PACKAGE CONTENTS
WARNING!
A (x1)
Mounting Plate
TOOLS NEEDED
Phillips
Screwdriver
B (x1)
Locking Plate
D (x2)
Cable Strap E (x4)
Pads
C (x1)
Clamp
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
S-A (x1)
Thumscrew
S-B (x2)
M4x6mm
Screw
S-C (x8)
M4x10mm
Screw
S-D (x4)
M5x6mm
Screw
S-E (x4)
M4 Washer
S-F (x4)
M4 Nut
S-G (x4)
M5 Washer
ASSEMBLY OPTIONS:
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury. 5lbs
(2.4kg)
Desk Clamp
pg. 3-5
Allows micro PC to clamp
to a desktop surface with a
thickness of 10mm to 50mm.
VESA Plate
Monitor Arm
pg. 6-8
Mount installs between
monitor and monitor
mount arm.
VESA Plate
Freestanding Monitor
pg. 9-11
Utilizes VESA holes in
freestanding monitor to
hold micro PC

3
ASSEMBLY OPTION A: Desk Clamp
STEP 2
STEP 1
For Desktops with a 10mm to 40mm Thickness:
Dissemble Clamp (C) using a Phillips screwdriver. Turn Lower Clamp (C1) upside and reassemble
Clamp (C) as shown below.
*For Desktops with a 15mm to 50mm Thickness:
Proceed to Step 2.
C
C1
Choose desired mounting orientation and connect Mounting Plate (A) to back side of Clamp (C) at
desired height using M4x6mm Screws (S-B) and a Phillips screwdriver.
CA
S-B

4
STEP 4
Place assembly onto desktop and tighten hand bolt to secure.
STEP 3
Secure Locking Plate (B) to back side of Mounting Plate (A) using M5x6mm Screws (S-D),
M5 Washer (S-G), and a Phillips screwdriver.
AS-D
S-G
B

5
STEP 5
Attach Pads (E) to the PC to procect against accidental damage, then securely place the PC into
the mount. Secure using Thumbscrews (S-A).
Attach Cable Straps (D) to slots on underside of assembled mount to secure charging cord
power brick.
E
S-A
D

6
ASSEMBLY OPTION B: VESA Plate - Monitor Arm
STEP 1
STEP 2
Secure Mounting Plate (A) to VESA holes on the back of the monitor using M4x10mm Screws (S-C)
and M4 Washers (S-E) and a Phillips screwdriver.
Attach Locking Plate (B) to the front side of the VESA Plate from your monitor mount using M4x10mm
Screws (S-C), M4 Nuts (S-F) and a Phillips screwdriver.
A
S-C
S-F
B
S-C
S-E

7
STEP 3
STEP 4
Secure Locking Plate (B) to Mounting Plate (A) using M5x6mm Screws (S-D), M5 Washers (S-G), and
a Phillips screwdriver.
S-D
S-G
B
A
Attach Pads (E) to the PC to procect against accidental damage, then securely place the PC into
the mount. Secure using Thumbscrews (S-A).
E
S-A

8
STEP 5
Attach Cable Straps (D) to slots on underside of assembled mount to secure charging cord
power brick.
Secure VESA plate to monitor mount using manufacturer guidelines.
D

9
ASSEMBLY OPTION C: VESA Plate - Freestanding Monitor
STEP 1
Secure Locking Plate (B) to Mounting Plate (A) using M5x6mm Screws (S-D), M5 Washers (S-G),
and a Phillips screwdriver.
Secure Mounting Plate (A) to VESA holes on the back of the monitor using M4x10mm Screws (S-C)
and M4 Washers (S-E) and a Phillips screwdriver.
S-C
S-E
A
S-D
AB
S-G

10
STEP 2
Attach Pads (E) to the PC to procect against accidental damage, then securely place the PC into the
mount. Secure using Thumbscrews (S-A).
E
S-A