Vivo MOUNT-KB05EL User manual

Black Clamp-on Keyboard Tray with RGB Lights
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-kb05el
SKU: MOUNT-KB05EL
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
ASSEMBLY STEPS
STEP 1
Assemble Keyboard Tray (A) using Connecting Plates (B) and M5x12mm Flat Head Screws (S-C).
Tighten with a Phillips screwdriver. Connect cables in Keyboard Tray (A) and then apply Tape (G) over
exposed area.
PACKAGE CONTENTS
WARNING!
TOOLS NEEDED
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
A(x1)
Keyboard Tray
G(x1)
Tape
B(x2)
Connecting Plate
E (x1)
Clamps
C(x1)
Keyboard Stop
D(x1)
Slider Brackets
F(x2)
Pad
S-A (x6)
M4x7mm Flat Head Screw
S-B (x8)
M5x12mm Screw
S-C (x12)
M5x12mm Flat Head Screw
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
11lbs
(5kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
STEP 2
Attach Keyboard Stop (C) to the back of Keyboard Tray (A) using M5x12mm Flat Head Screws (S-C) and
a Phillips screwdriver.
G
A
B
S-C

3
STEP 3
Assemble Slider Brackets (D) to Keyboard Tray (A) using M5x12mm Screws (S-B), and tighten with a
Phillips screwdriver. Slider Brackets (D) should protrude from the back of the keyboard tray assembly.
STEP 4
Assemble Clamps (E) to the Slider Brackets (D) using M4x7mm Flat Head Screws (S-A). Tighten with a
Phillips screwdriver.
STEP 5
STEP 6
Place Pads (F) on the underside of each Clamp (E). Place assembled keyboard mount on the edge of
the desktop and tighten Clamps (E).
E
D
S-A
Desktop
Desktop
“+”
“M”
“-”
Increase Brightness
Quick press: Cycle
through color modes
Hold for 3 seconds:
Powers o lights
Decrease Brightness
F
E
Plug Keyboard Tray (A) into a 5V USB power supply. Follow the diagram below for operation.
A

LAST UPDATED: 11/30/2022
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303