Vivo MOUNT-V001GL User manual

Pneumatic Arm Single Laptop Wall Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-v001gl
SKU: MOUNT-V001GL
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
ASSEMBLY STEPS
PACKAGE CONTENTS
TOOLS NEEDED
9.9lbs
(4.5kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
A(x1)
Arm
B(x2)
Cover
D(x1)
Laptop Tray
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
STEP 1
OPTION A: Wood Stud Wall
Use a pencil to mark drilling
locations and drill 2.2” (55mm)
deep holes using 3/16” (4.5mm)
bit. Use of a stud finder is
recommended. Mount arm (A) to
wall using ST6.3x55 screws (W-A)
and D6 washers (W-C). Do NOT use
concrete anchors (W-B) for wood
stud installation.
C(x1)
5mm Allen
Wrench
E(x2)
Laptop Arm
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
F(x2)
Clip
4.4-19.8lbs
(2-9kg)
LAPTOP MONITOR
G(x4)
M4x8
M-A (x4)
M4x12
M-C (x4)
D5 Washer
M-B (x4)
M5x12
W-A (x2)
ST6.3x55
W-B (x2)
Concrete Anchor
W-C (x2)
D6 Washer
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO MOUNT. We
include mounting hardware for brick and concrete walls. If unsure, please contact us at vivo-us.com, email at help@
vivo-us.com, or call us at 309-278-5303.
CAUTION!

3
STEP 1 (Continued)
STEP 2
Press covers (B) into screw holes.
OPTION A: MONITOR INSTALLATION STEP 1
Install screws (M-A or M-B) with D6 washers
(M-C) in top two holes of the monitor, leaving
3mm of space between the screw heads and
the monitor. Hang monitor with screws over
slots in the VESA plate. Insert screws (M-A or
M-B) with D5 washers (M-C) into lower two
holes and tighten using the Phillips end of the
5mm Allen Wrench (C).
OPTION B: Brick/Concrete Wall
Use a pencil to mark drilling locations
and drill 2.4” (60mm) deep holes
using a 3/8” (10mm) bit. Mount arm
(A) to wall using ST6.3x55 screws
(W-A), concrete anchors (W-B) and D6
washers (W-C).

4
STEP 2
While holding the arm straight
forward, adjust arm tension by
turning the screw on top of the center
arm joint with the 5mm Allen wrench
(C). Turn clockwise to reduce tension
and counterclockwise to increase.
The tension should be just enough to
hold your monitor in place without
liing itself up. If needed, adjust bolts
on the sides of the hinge behind the
VESA plate to tighten or loosen the
tilt support.
STEP 3
Remove cable covers by removing the
screw underneath each one.
STEP 4
Insert cables and replace covers while
making sure the cables have enough
slack to allow enough free movement
of the arm.

5
OPTION B: LAPTOP INSTALLATION STEP 1
STEP 5
Adjust monitor position as desired.
Place laptop arms (E) underneath each side of the laptop tray (D), aligning the square holes in the arms
with the edge and long slot on each side. Insert clips (F) through the top to secure the arms, making
sure all 4 locks on each clip are engaged with the square holes in the arms.
STEP 2
Attach assembled laptop holder to
75mm and 100mm holes on the arm
(A) using M4x8 screws (G). Tighten
screws using the Phillips end of the
5mm Allen Wrench (C).
STEP 3
Release the locks on the underside of the laptop arms (E). Extend arms, place laptop in the holder,
then adjust the arms to fit the width of the laptop. Engage locks to secure the laptop. If using a thicker
laptop, turn the front bumpers to the upward position for additional support.

6
STEP 4
While holding the arm straight forward, adjust arm tension by turning the screw on top of
the center arm joint with the 5mm Allen wrench (C). Turn clockwise to reduce tension and
counterclockwise to increase. The tension should be just enough to hold your laptop in place
without liing itself up. If needed, adjust bolts on the sides of the hinge behind the VESA plate
to tighten or loosen the tilt support.
STEP 5
Remove cable covers by removing the screw underneath each one.

7
STEP 6
Insert cables and replace covers while making sure the cables have enough slack to allow enough free
movement of the arm.
STEP 7
Adjust laptop position as desired.

LAST UPDATED: 08/06/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303