Vivotek 4X-SD8111 User manual

Quick Installation Guide
SD8111/SD8121
English 繁中 日本語 Español Português
簡中 Français Deutsch Italiano Türkçe Polski Русский Česky Svenska
P/N: 625012000G Ver.1.0
Copyright 2010 VIVOTEK INC. All rights reserved.
c
H.264 12x Zoom Day&Night 3D Noise Reduction

EN - 1
English
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Contact your distributor in the event of
occurrence.
Keep the Network Camera away
from water. If the Network Camera
becomes wet, power off immediately.
Do not place the Network Camera
around heat sources, such as a
television or oven.
Refer to your user's manual for the
operating temperature.
Keep the Network Camera away from
direct sunlight.
Do not place the Network Camera in
high humidity environments.
Contact your distributor in the event of
occurrence.
Warning Before Installation

EN - 2
Do not place the Network Camera on
unsteady surfaces.
Do not touch the Network Camera
during a lightning storm.
Do not disassemble the Network
Camera.
Do not drop the Network Camera.
Do not insert sharp or tiny objects
into the Network Camera.

EN - 3
English
Fixing Plate
SD8111 / SD8121
Cable Connector (Power, Video Out,
Mic In, Audio Out, Ground)
Software CD
Hard Ceiling Mount Bracket and
Decoration Ring
5
1
0
0
0
0
2
1
0
G
Package Contents
1
Power Adaptor
Quick Installation Guide /
Warranty Card
DI/DO Cable Connector

EN - 4
Record the MAC address before
installing the camera.
Lens
Physical Description
2
SD/SDHC Card Slot
Dome Cover
0002D107258A
Reset Button
Restore Button
Ethernet 10/100 RJ45 Socket
Cable Connector Socket

EN - 5
English
Follow the steps below to install the Network Camera to the ceiling:
1. Detach the Decoration Ring from the Hard Ceiling Mount Bracket.
2. Align the three holes on the Mount Bracket, mark the screws locations on the ceiling.
3. Drill three pilot holes into the ceilling and hammer the plastic anchors into the holes.
4. Fix the Mount Bracket with three screws.
Hardware Installation
3
3
14
2

EN - 6
5. Put the decoration ring onto the dome body.
6.Insertthexingplateintothegrooveasshownbelow.
7.Alignthethreeholestoscrewthexingplatetothedomebase.
56
0002D107258A
7
0002D107258A

EN - 7
English
8. If you have external devices such as sensors and alarms, connect them to the general
I/O terminal block. Then connect the cable connector and Ethernet cable to the dome
base.
9. Align plate A and plate B, use hole a ~ c to hook the Network Camera on the ceiling
mount bracket.
8
9
8
9
A
B
1 3
2 4
21
22
0002D107258A
a
bc
0002D107258A
12: DI 0
13: DI 2
14: DI 1
15: DI 3
16: DO
Pin Denitions of Cable Connector

EN - 8
POW ER COLLISION
LINK
RECEIV E
PARTITION
12345
Ethernet Switch
Power Cord Socket
BNC Video Out
Microphone In (pink)
Audio Out (green)
Ethernet 10/100 RJ45 Plug
12. Connect the cables and make the network deployment.
Ground
10.Tightenthescrewonthexingplate.
11. Align the three holes to mount the decoration ring.
11
10

EN - 9
English
0002D107258A
1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network is
analyzed, please click on the “Next” button to continue the program.
3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network
Cameras on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that matches the
one labeled on the bottom of your device to connect to the Network Camera via Internet
Explorer.
0002D107258A
00-02-D1-07-25-8A 192.168.5.151 SD8121
Installation
Wizard 2
Assigning an IP Address
4