Vivotek SD9361-EHL User manual

Quick Installation Guide
VIVOTEK INC.
6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
|T:[phone]|F:[phone]|E:[email protected]
VIVOTEK USA, INC.
2050 Ringwood Avenue, San Jose, CA 95131
|T: 408-773-8686 |F: 408-773-8298 |E: [email protected]
2MP • 20x/30x Zoom • 60fps • NEMA 4x • IP68 • Extreme Weatherproof
All specications are subject to change without notice.
Copyright 2016 VIVOTEK INC. All rights reserved.
c
P/N:625033602G Rev.: 1.2
SD9362-EH/EHL Speed Dome
Network Camera
English 繁中 日本語 Español Português
簡中 Français Deutsch Italiano Türkçe Polski Русский Česky Svenska
Dansk
Nederlands
Indonesia
VIVOTEK Europe
Randstad 22-133, 1316BW Almere, The Netherlands
T:[phone] E:[email protected]
SD9361-EHL

EN-1
English
Warning Before Installation
Refer to your user’s manual for the
operating temperature.
Power off the Network Camera as soon as
smoke or unusual odors are detected.
Do not touch the Network Camera during
a lightning storm.
Do not disassemble the Network Camera.
Do not drop the Network Camera.
Do not insert sharp or tiny objects into the
Network Camera.
Do not manually pan and tilt the Network
Camera when the power is on.
Package Contents
1
5
1
0
0
0
0
2
1
0
G
Software CD
Wall Mount Bracket / ScrewsSD9361/ SD9362
Quick Installation Guide
I/O Combo Cable
Screws / Alignment Sticker / T20 and T25
L-wrench / Desiccant Bags
IMPORTANT:
Below are the requirements for powering the the speed dome:
Feature Power Consumption
Normal w/ heater 48W, requires a 60W PoE injector (AP-GIC-010A-060) or PoE switch (AW-
IHU-0100, -0200, -0600); AC24V (3.5A) also applies
w/ IR unit 95W, VIVOTEK's AW-IHU-0101 & AW-IHU-0201
DC 24V (3.5A) applies, AC 24V is not sufcient.

EN-2
Top View
IR unit connector
Lens
Outer View
Physical Description
2
LAN connector
Status LED
Reset Button
This drawing shows a camera with its dome
cover removed.
MicroSD card slot
Safety wire hook
I/O combo connector
Alignment marks

EN-3
English
Hardware Installation
3
Ø 9.5mm or 3/8”
1. Jot down the camera's MAC address for later reference.
2. The camera weighs 3kg. Select a rigid mounting location to prevent vibration to the
camera. Attach the alignment sticker to the wall.
3. Drill 4 pilot holes (9.5mm in diameter and 4cm deep) into the wall, and then hammer
in threaded anchors. Note that you should hammer the anchors with hex nuts on
them so that the threaded poles will not be deformed! If preferred, drill another hole
for routing cables.
4. Remove the hex nuts, washers, and leave one washer on each of the threaded poles.
0002D10766AD
SDXXXX

EN-4
LAN I/O combo
5. Connect power or I/O wires, and use foam tapes or seal foam to ensure the back-end
connection is waterproof.
6. Route your I/O combo and Ethernet cables along the routing guide poles to form drip
loops.

EN-5
English
7. Secure the bracket to wall.
15cm
8. Remove the cable gland from the LAN port. If I/O wires
or 24V power are preferred, use the T20 L-wrench to
remove the top cover on the I/O connectors.
T20
The cable length hanging on the out-
side of the bracket should be 15cm
IMPORTANT:
Make sure all waterproof cable glands have
been properly installed. Water leakage will
cause irrepairable damage to the camera.

EN-6
9. Hook up the safety wire between the bracket and the camera.
4.3 ~ 6.4mm
10. Install the components of the waterproof cable gland to the Ethernet and I/O com-
bo cables.
The outer jacket
of the combo
cable is ush with
cabling hole.

EN-7
English
11. Connect the I/O wire headers to camera and then secure the top cover.
T20
12. Connect the Ethernet cable (along with its cable gland) to the camera.
NOTE:
To disconnect a LAN cable, loosen the cable
gland and pull the cable against the socket
wall towards the side of the locking tab.
1
2

EN-8
13. Install the camera to bracket by aligning the mark on bracket with the #1 marking
on the camera.
1
2
14. Turn the camera clockwise. The camera should be locked in place.
15. Secure the connection using the T25 L-wrench from
the top.
T25

EN-9
English
16. Open the dome cover using the T20 L-wrench. Install a microSD card, and replace
the desiccant bag on the inner side of camera chassis.
M
icro
SD
T20
17. Remove the foam blocks in the chassis, and the front and rear of the lens module.
Also remove the plastic sheet from the inside of the dome cover.
18. When done, secure the dome cover
using the T20 L-wrench.