Vivotek AT-CAB User manual

IP Surveillance
Installation Guide
AT-CAS
Surveillance Cabinet
AT-CAB
Document part no.: 625034802G
Rev.: 1.2

2
CAUTION:
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
UNPACKING:
Unpack carefully. Electronic components can be damaged if improperly handled or
dropped. If an item appears damaged in shipment, place it properly in its carton and
notify the shipper.
1. The electrical connections and conduit installations shall be made by a certied electrician following
local regulations.
2. Risks of electric shock exist. The mains supply shall be disconnected before installation.
3. Read and follow Instructions: All operating and user instructions should be read and followed before
the unit is to be operated.
4. This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that
the protective device is listed rated not greater than 20A.
5. Attach the ground wire (to external ground) to a suitable grounding point, e.g., an earth stake.
6. Observe national and local regulations for the installation.
7. To avoid additional accummulation of moisture, please avoid installing the components in cabinet
during a raining weather.
8. Only use applicable tools when installing this product; excessive force can damage the product.
9. Use only accessories compliant with the technical specications of the product.
10. When the need arises for transportting this product, it is recommended to use the original shipping
package.
IMPORTANT!:
Revision History:
Rev. 1.0: Initial release.
Rev. 1.1: Added screw type description, applicable accessories, and cable gauge information.
Rev. 1.2: Added a table for the included parts/accessories.

3
English
Applicable Modules & Components
I
Item Models
AT-CAB-001 Cabinet
AT-CAS-001 Cabinet for speed dome
Optional accessories Models
AW-IHS-0200 Industrial Fiber-Ethernet converter, SC type, multi-mode, 2km.
AW-IHS-0201 Industrial Fiber-Ethernet converter, SC type, single mode, 30km
AW-IHS-0203 Industrial Fiber-Gb Ethernet converter, LC type.
AW-IHT-0100 Industrial GbE PoE injector, 30W output.
AW-IHU-0100 Industrial GbE UPoE injector, 60W output.
AW-IHH-0100 Industrial GbE PoH/PoE injector, 95W output.
AW-IHT-0200 Industrial 1xGb PoE, 1xGb ber SFP switch, 30W output.
AW-IHU-0200 Industrial 1xGb UPoE, 1xGb ber SFP switch, 60W output.
AW-IHH-0200 Industrial 1xGb PoH/PoE, 1xGb ber SFP switch, 95W output.
AW-IHT-0500 Industrial 4x 10/100BaseT, 1x SFP, PoE switch, 30W output, 120W budget.
AW-IHT-0501 Industrial 4x 10/100BaseT, 1x SC 2km, PoE switch, 30W output, 120W budget.
AW-IHT-0502 Industrial 4x 10/100BaseT, 1x SC 30km, PoE switch, 30W output, 120W budget.
AW-IHT-0600 Industrial 4x GbE, 1x Combo GE + 1x GE SFP, PoE switch, 30W output, 120W
budget.
AW-IHT-0601 Industrial 4x GbE, 1x Combo GE + 1x GE SFP, PoE switch, 30W output, 120W
budget.
AW-IHU-0600 Industrial 4x GbE, UPoE, 2x GbE SFP, PoE switch, 60W output, 240W budget.
Optional accessories Models
IRM-60-12ST 85~264VAC input, 12VDC/60W output power supply, -30ºC ~ 70ºC
IRM-60-48ST 85~264VAC input, 48VDC/60W output power supply, -30ºC ~ 70ºC
NDR-75-48 90~264VAC input, 48VDC/75W output power supply, -20ºC ~ 70ºC
NDR-120-48 90~264VAC input, 48VDC/120W output power supply, -20ºC ~ 70ºC
NDR-240-48 90~264VAC input, 48VDC/240W output power supply, -20ºC ~ 70ºC
HLG-80H-24 90~305VAC input, 24VDC/80W output power supply, IP67, -40ºC ~ 70ºC
HLG-80H-48 90~305VAC input, 48VDC/80W output power supply, IP67, -40ºC ~ 70ºC
HLG-80H-54 90~305VAC input, 54VDC/80W output power supply, IP67, -40ºC ~ 70ºC
HLG-120H-24 90~305VAC input, 24VDC/120W output power supply, IP67, -40ºC ~ 70ºC
HLG-120H-48 90~305VAC input, 48VDC/120W output power supply, IP67, - 40ºC ~ 70ºC
HLG-120H-54 90~305VAC input, 54VDC/120W output power supply, IP67, -40ºC ~ 70ºC
HLG-240H-54 90~305VAC input, 54VDC/240W output power supply, IP67, -40ºC ~ 70ºC
AT-SPC-001 30A solar power controller

4
Optional mech. & safety
accessories
Models
AT-CAB-002 Side-mount bracket for HLG series power supply
AT-SUN-001 Sunshield for AT-CAx series cabinet
AT-SUN-002 Sunshield for AT-CAx + AT-CAB-002 cabinet
AT-WPC-001 M16 cable gland for cables 4~7mm AWG
AT-WPC-002 M16 cable gland for corrugated tubing: 1/16"
AT-PSP-001 PoE surge protector
AT-SWH-000 Power safety kit
AT-SWH-002 Door open/close detection switch
Included Parts
Item Specs Quantity Item Specs Quantity
Screw M3x4 2 Terminal block 1
Screw M3x8 10 Terminal block
bracket
1
Screw M3x12 4 Routing
bracket
2
Screw M3x14 2 DIN rail
bracket
1
Screw M4x6 4 Door alarm
detector pole
2
Screw M4x8 15 Fiber optic
holder
3
Cable gland 3/4" 1 Sleeve anchor 4
Wire holder KTCC-6 6
Wire holder KTCC-9 6
L wrench T30 1
Cable tie 32cm 4
Cable tie 22.5cm 4

5
English
Introduction
II
3/4” conduit hole
(cable gland included)
M16 conduit holes
Hinge
(door can be opened
from either side)
Mounting plate
Cabinet door
AM-311
The rest of the
mounting holes
apply to wall mounting
3/4” conduit hole
(for side-mounted PWR)
The cabinet can be installed to a wall, a corner-mount (AM-411), or a pole-mount (AM-311) bracket.
You can use the unused mouting holes for installing several cable clamps for routing the cables.

6
Vertical DIN rail
(for lighter modules) Vertical DIN rail
(for heavier modules)
Terminal block
Horizontal DIN rail
(for safety kit)
DC power supply
(HLG-80)
Routing bracket
Surge protector
The cabinet provides various mounting positions for different devices. The positions are shown shown
in the following diagrams.
Installation
III

7
English
DC power
supply
IRM-30
DC power supply
HLG-120
The combination and the choice of components within the cabinet depends on the cameras you want
to deploy using this cabinet. Select your devices with the consideration of power consumption, cabling
distance, the number of cameras, the opertating temperature, and so on. Multiple devices can be
stacked as along as the space within the cabinet allows.
Application
Power
Switch
Fiber Fiber Fiber
VMS

8
DC power supply
IRM-60
PoE injector
Door alarm
detector pole
Fiber optic
cable holders

9
English
Solar power
controller

10
Safety kit
Routing
brackets Surge
protector
Terminal
block
PoE switch, power
supply, media
converter, etc. on
DIN rail.
Below are some of the conguration samples.
Door on/off
detection pole
DC power supply
IRM-60block
DC power supply

11
English
Fiber optics cable
holders
If ber optics cables are used, install the cable holders for the bend radius concern.
Make sure the combined height of screw head and washer
does not exceed 12mm
IMPORTANT: Shown below is the status of a cabinet mounted on top of the mounting plate. If
a different type of mounting screws is preferred, make sure the combined height of screw head
and washer does not exceed 12mm.

12
Vertical DIN rail
(for heavier modules)
You can install one or two PoE switch, media converter, or industrial power supply to the vertical DIN
rail. Please refer to page 2 and page 3 for information.

13
English
The cabinet door can be used for housing the Ethernet surge protectors. Use the mounting holes on the
cabinet door for surge protector and the door switch detector. Note that a hex pole should be installed
in the cabinet if the door switch detector is installed.
Door lock detector
Installing Modules to the Cabinet Door
Connect the detection wires to a camera's DI pins. Congure an event
trigger when the door is opened via a web console with the camera in
Conguration > Event > Event settings so that an intrusion can be
reported via Email, FTP, HTTP, or to a Networked storage.

14
The HLG-120H and HLG-240H power supplies can be side-mounted using an additional bracket to side
of the cabinet. Secure the side bracket using 6 included screws, feed the cables through the 3/4" cable
gland, and then secure the power supply to the bracket. The power supplies are weatherproof.
When nished, secure the plastic top cover.
The event conguration screens should look like the following:
Side-mounting a Power Supply
+V(Red)
-V(Black)
FG (Green/Yellow)
AC/L(Brown)
AC/N(Blue)SJTW 14AWG 2C×
SJTW 18AWG 3C×

15
English
Refer to the diagrams below for the different types of screws and their applications.
Screw Types
M4 x 6 machine screws
M3 x 14 machine screws w/
washer
For securing terminal block
M4 x 8 tapping screws
M4 x 8 tapping screws
If DIN rail is installed using
these two holes.

16
M3 x 8 tapping screws w/
washer
M4 x 8 tapping screws

17
English
M3 x 12 tapping screws
w/ washer

18
M3 x 8 tapping screws w/
washer

19
English
Circuit breaker
Surge protector Terminal block
(feed through)
Terminal block
(ground)
Wiring & Connections
IV
Insatll 3/4" and M16 cable glands and cable conduits to protect the cables and the wiring to the outside
of the cabinet. Properly install the cable glands so that the product's IP rating is maintained. If not
properly installed, water may seep into the cabinet, causing damage to devices inside.
The conduits are user supplied. The cabinet comes with 1 3/4" cable gland only.
Below are the instructions for wiring a safety kit combination that includes a circuit breaker, surge
protector, and terminal blocks.

20
Line
Neutral
Neutral
Terminal block
(ground)
Line
Ground
External ground
Surge protector: solid wire, 2.5 to 25mm2
striping length: 12.5mm
Cable Gauge:
Circuit breaker: Cross-section of conductors (top/bottom) - solid wire, 35mm2; Flexible, 25mm2,
14 - 4 AWG
Cross-section of busbars (top/bottom) - 10mm2; 14 - 8AWG
Grounding Terminal block: Cross-section of conductors (top/bottom) - solid wire & exible,
30~12mm2; 0.2~2.5 AWG