Vivotek IP7151 User manual

EN - 1
English
Contact your distributor when such
cases happen.
Keep the Network Camera away
from water. If the Network Camera
is wet, power off immediately.
Refer to your user's manual for the
operating temperature.
Power off the Network Camera
as soon as it is found smoking or
smelt unusual.
Do not place the Network Camera
around the heat sources, such as
television or oven.
Keep the Network Camera away
from direct sunlight.
Do not place the Network Camera
in high humid environments.
Contact your distributor when such
cases happen.
Warning Before Install

EN - 2
Do not place the Network Camera
on unsteady surfaces.
Do not touch the Network Camera
when it's lightening.
Do not disassemble the Network
Camera.
Do not drop the Network Camera.
Do not insert any object into the
Network Camera, such as needles.

E
N - 3
E
ng
li
s
h
C
amera stand
L
en
s
I
P7151 / IP7152
Warrant
y
car
d
Q
uick installation
g
uid
e
S
oftware C
D
A
ntenna
(
IP7152 onl
y)

EN - 4
Power cord socket
Ethernet 10/100
RJ45 socket
Indented reset button
General I/O
terminal block
Audio out
MIC in
External/Internal
MIC switch
Front panel
Back panel
Lens
Focus controller
Zoom controller
2Physical Description
Built-in MIC
Light sensor
Status LED
Antenna
(IP7152 only)
Antenna
(IP7152 only)

EN - 5
English
For further setup, please refer to the lens' instruction manual inside the
lens package.
1. Mount the lens by turning it clockwise onto the camera mount until it stops. If
necessary, turn the lens counterclockwise slowly until it gets the best attitude.
2. Connect the lens cable plug to the camera connector.
3. Unscrew the zoom controller to adjust the zoom factor. Upon completion, tighten
the zoom controller.
4. Unscrew the focus controller to adjust the focus range. Upon completion, tighten
the focus controller.
W
∞
N
T
1
2
4
3
3Mounting the Lens to the Camera

E
N - 6
General Connection (without PoE)
()
1
.
C
onnect the camera to a hub via Ethernet cable
.
2
. Connect the su
pp
lied
p
ower cable from the camera to a
p
ower outlet
.
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
1
2
E
thernet hub

EN
-
7
E
ng
li
s
h
Power over Ethernet (PoE) (IP7151 only)
()( y)
POWER COLLISION
LINK
RECEIV E
PARTITION
12345
PoE
hub
POWER COLLISION
LINK
RECEIV E
PARTITION
12345
W
hen usin
g
a non-PoE hu
b
U
se a PoE power in
j
ector
(
optional
)
to connect between the camera and a non
-
Po
E h
ub.
no
n-
PoE
hub
P
oE power in
j
ecto
r
(
optional)
Wh
en us
i
ng a
P
o
E
-ena
bl
e
d
h
u
b
T
he camera is PoE-compliant, allowing transmission of power and data via single
E
thernet cable.
S
ee the
f
ollowing illustration to connect the camera to a PoE-
e
n
ab
l
ed
h
ub
vi
a
Eth
e
rn
e
t
cab
l
e.

EN - 8
T15CCO
1T
2
RoHS
Network Camera
Model No:IP7151
P3 T
MAC:0002D1070417
1. Run the "Installation Wizard 2" under the Software Utility directory from software
CD.
2. The program will conduct analyses on your network environment. After your
network is analyzed, please click on the "Next" button to continue the program.
3. The program will search the Vivotek Video Receivers, Video Servers or Network
Cameras on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that
matches the one labeled on the bottom of your device to connect the Internet
Explorer to the Network Camera.
21 41 121 21 IP 151
IW2
5Assigning IP Address
0002D1070417

EN - 9
English
For further setup, please refer to user's manual on the software CD.
6Retrieving Images