Vivotek IP7153 User manual

EN - 1
English
Contact your distributor in the event of
occurrence.
Keep the Network Camera away from
water. If the Network Camera becomes
wet, power off immediately.
Refer to your user’s manual for the
operating temperature.
Power off the Network Camera as
soon as smoke or unusual odors
are detected.
Do not place the Network Camera
around heat sources, such as a
television or oven.
Keep the Network Camera away
from direct sunlight.
Do not place the Network Camera in
high humidity environments.
Contact your distributor in the event of
occurrence.
Warning Before Installation

EN - 2
Do not place the Network Camera
on unsteady surfaces.
Do not touch the Network Camera
during a lightning storm.
Do not disassemble the Network
Camera.
Do not drop the Network Camera.
Do not insert sharp or tiny objects
into the Network Camera.

EN - 3
English
Camera Stand Lens
IP7153 / IP7154
Warranty Card
Power Adapter
Quick Installation Guide Software CD
1Check Package Contents
Antenna (IP7154 only)
ST7501
Central Management Software

EN - 4
Power Cord Socket
Ethernet 10/100
RJ45 Socket
Recessed Reset Button
General I/O
Terminal Block
Audio Out
Microphone In
External/Internal
Microphone Switch
Front Panel
Back Panel
Lens
Focus Controller
Zoom Controller
2Physical Description
Built-in Microphone
Light Sensor
Status LED
Antenna
(IP7154 only)
Antenna
(IP7154 only)

EN - 5
English
For further setup, please refer to the lens' instruction manual inside the
lens package.
1. Mount the lens by turning it clockwise onto the camera mount until it stops. If
necessary, turn the lens counterclockwise slowly to achieve the best optimum
spacing.
2. Connect the lens cable plug to the camera connector.
3. Unscrew the zoom controller to adjust the zoom factor. Upon completion, tighten the
zoom controller.
4. Unscrew the focus controller to adjust the focus range. Upon completion, tighten the
focus controller.
W
∞
N
T
1
2
4
3
3Mounting the Lens to the Camera

EN - 6
General Connection (without PoE)
1. Connect the camera to a switch via Ethernet cable.
2. Connect the power cable from the Network Camera to a power outlet.
POWER COLL ISION
LINK
RECEI VE
PARTITION
12345
1
2
Ethernet Switch
4Network Deployment

EN - 7
English
Power over Ethernet (PoE) (IP7153 only)
POWER COLLISION
LINK
RECEIV E
PARTITION
12345
PoE Switch
POWER COLLISION
LINK
RECEIV E
PARTITION
12345
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and a
non-PoE switch.
Non-PoE Switch
PoE Power Injector
(optional)
When using a PoE-enabled switch
This Network Camera is PoE-compliant, allowing transmission of power and data via
a single Ethernet cable. Follow the below illustration to connect the Network Camera
to a PoE-enabled switch via Ethernet cable.

EN - 8
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
RoHS
Network Camera
Model No:IP7153
Pat. 6,930,709 Made in Taiwan
MAC:0002D1070417
1. Install "Installation Wizard 2" from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network
is analyzed, please click on the "Next" button to continue the program.
3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network
Cameras on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that matches
the one labeled on the bottom of your device to connect to the Network Camera via
Internet Explorer.
00-02-D1-07-04-17 192.168.0.219 IP7153
Installation
Wizard 2
5Assigning an IP Address
0002D1070417

EN - 9
English
For further setup, please refer to user's manual on the software CD.
6Ready to Use
1. Access the Network Camera on the LAN.
2. Retrieve live video through the web browser or recording software.