Vivotek IP8336W User manual

EN - 1
English
Warning Before Installation
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Keep the Network Camera away
from water. If the Network Camera
becomes wet, power off immediately.
Do not place the Network Camera
around heat sources, such as a
television or oven.
Refer to your user’s manual for the
operating temperature.
Keep the Network Camera away from
direct sunlight.
Do not place the Network Camera in
high humidity environments.
Do not place the Network Camera on
unsteady surfaces.
Do not touch the Network Camera
during a lightning storm.
Do not disassemble the Network
Camera.
Do not drop the Network Camera.
Do not insert sharp or tiny objects
into the Network Camera.

EN - 2
Camera Stand
Warranty Card
Screws
Quick Installation Guide
Power Adaptor (+12V, 2A)
Package Contents
1
Software CD
5
0
0
0
2
4
7
0
1
G
Antenna
IP8336W

EN - 3
English
Physical Description
2
Front Panel
Status LED
Lens
Microphone
Item LED status Description
LED Definitions
1 Steady Red Powered and system booting, or network failed
2 Blue LED blinks every 0.15 sec. Searching for WPS
3 Green LED blinks every 1 sec. Network connected to an AP
4 Green and RED blink consecutively every 0.15 sec. Upgrading firmware
5 Steady Blue Operating in camera default AP mode
6 Orange blinks every 0.15 sec. Restoring defaults
7 All LED off Powered off
Light Sensor
Antenna
Back Panel
Mounting Hole
Power and I/O Combo Cable
IR LEDs behind panel

EN - 4
Reset button
WPS button
NOTE:
An antenna comes with the camera. Install it by turning
clockwise to attach to the connector.
Network Deployment
3
1. If you have external devices such as a sensors and alarm, make connections from the
digital input connector.
2. Connect the power line to the power adaptor.
DI+
DI-
Power Connection
Bottom View
MicroSD/SDHC
Card Slot

EN - 5
English
WPS
Wireless Connection #1: Using the WPS Button
1. Make sure your AP (Access Point) and Operating System support WPS (Wi-Fi
Protected Setup) functions. WPS enables easy setup with compatible APs.
2. Use the included hex wrench to open the bottom cover.
3. Use the hex wrench to press the WPS button for 1 second.
The camera LED should flash green. When WPS configuration is done, wireless
connectivity will be established and the security encryption, such as WEP or WPA-
PSK, will be synchronized with the AP. Use the IW2 utility to find the camera. As for IP
setting, the camera's use of DHCP or static IP is determined by your configuration on the
network camera via the web-based configuration of firmware. The camera's default is
DHCP.
NOTE:
WPS Button
WPS Button
Wireless AP
1. WPS may not work if your AP is configured with a "hidden" SSID.
2. If no WPS-enabled AP is detected, the camera will continue searching for AP for 2
minutes. After that, the wireless setup will be cancelled.
When powered on, the camera LED should
light red for a minute, and then turn blue.
When lit blue, the camera operates in the AP
mode.
4. Press and hold down the WPS button on your AP (some router/AP will
have a virtual button on their management software instead). Refer to
your AP's documentation for details using its WPS functions.

EN - 6
1
2
3
AP
Wireless Connection #2: Connection without WPS
2. Right-click or double-click on the VIVOTEK (MAC addr) icon. The camera name is
presented as: "VIVOTEK: (the last 4 digits of the camera's MAC address)."
Open a browser session using the camera's default IP "192.168.1.1"
If not using the WPS method, you can manually configure the camera:
1. Connect power to the camera. By default, the camera operates in the AP mode. Connect
to the camera using a Wi-Fi capable notebook or a computer with a wireless adaptor.
Open the internet dialog box by clicking the wireless networks icon on the system tray.
VIVOTEK (1C:CC)
AP mode
Client
mode

EN - 7
English
You can also discover the camera
using the IW2 utility. Install the IW2
utlity from the included product CD.
3. Enter your wireless AP's SSID and security password to connect to an existing AP. You
may also use the "Search your AP" button to locate an AP of your preferrence. Double-
click on an AP to make the connection.
Select the security encryption, such as
WEP or WPA-PSK, the algorithm, and
enter the pre-share key. Click Save to
proceed.
The camera will then operate in the
Client mode.

EN - 8
2011/01/05 01:50:28
5. A browser session with the Network Camera should prompt as shown below.
6. You should be able to see live video from your camera. You may also install the
32-channel recording software from the software CD in a deployment consisting of
multiple cameras. For its installation details, please refer to its related documents.
4. Open the IW2 utility. The camera will be assigned with a new IP address. Double-click
on it to start a web session. The camera LED will start blinking green by every second.
NOTE:
When you encounter configuration errors,
you can press the WPS button for 5
seconds to restore network settings. The
camera will resume the AP mode and the
LED will light blue.
WPS

EN - 9
English
Wireless Connection #3: Initial Setup Using a Cell Phone
VIVOTEK (1C:CC)
2. Once connected, you should connect the camera to
another AP. You should open a browser, enter the
camera's default IP (192.168.1.1) in the URL field.
When connected, manually enter the SSID and
security code for access to another AP, or use the
"Search your AP" function to search for nearby APs.
The search may take several seconds.
3. Select and connect to a preferred AP.
1. Connect power to the camera. Search for the camera in the Wi-Fi Networks. The camera
initially operates in the AP mode. Screen captures have been taken from an iPhone®.