Vivotek IZ9361-EH User manual

User’s Manual
H.265 • Outdoor • 20x Zoom • 2MP • Day & Night • 150M VAIR • 60fps
Smart Stream II • IP67 • EIS • Video Rotation
Zoom Bullet
Network Camera
IZ9361-EH
Rev. 1.0

VIVOTEK
2 - User's Manual
Table of Contents
Overview ..............................................................................................................................................................3
Revision History ...............................................................................................................................................3
Read Before Use..............................................................................................................................................4
Package Contents ............................................................................................................................................4
Symbols and Statements in this Document......................................................................................................5
Physical Description .........................................................................................................................................5
Hardware Installation........................................................................................................................................8
Network Deployment ......................................................................................................................................18
Software Installation .......................................................................................................................................20
Ready to Use..................................................................................................................................................21
Accessing the Network Camera .................................................................................................................... 22
Using Web Browsers......................................................................................................................................22
Using RTSP Players.......................................................................................................................................25
Using 3GPP-compatible Mobile Devices........................................................................................................26
Using VIVOTEK Recording Software .............................................................................................................27
Main Page......................................................................................................................................................... 28
Client Settings .................................................................................................................................................. 33
Conguration.................................................................................................................................................... 38
System > General settings .............................................................................................................................39
System > Homepage layout ..........................................................................................................................41
System > Logs ...............................................................................................................................................44
System > Parameters ....................................................................................................................................46
System > Maintenance...................................................................................................................................47
Media > Image .............................................................................................................................................51
Media > Video ................................................................................................................................................60
Media > Audio.................................................................................................................................................67
Network > General settings............................................................................................................................68
Network > Streaming protocols ....................................................................................................................76
Network > SNMP (Simple Network Management Protocol)...........................................................................85
Security > User accounts ...............................................................................................................................86
Security > HTTPS (Hypertext Transfer Protocol over SSL) .................................................................87
Security > Access List ..................................................................................................................................94
PTZ > PTZ settings ........................................................................................................................................99
PTZ...............................................................................................................................................................102
Mechanical PTZ Conguration .....................................................................................................................102
Event > Event settings..................................................................................................................................105
Applications > Motion detection....................................................................................................................119
Applications > DI and DO ...........................................................................................................................122
Applications > Audio detection ...................................................................................................................123
Applications > Package management - a.k.a., VADP (VIVOTEK Application Development Platform) .......125
Recording > Recording settings ..................................................................................................................128
Local storage > SD card management.........................................................................................................133
Local storage > Content management .........................................................................................................134
Appendix ........................................................................................................................................................ 137

VIVOTEK
User's Manual - 3
URL Commands for the Network Camera................................................................................................ 137
Technology License Notice....................................................................................................................... 331
Electromagnetic Compatibility (EMC)....................................................................................................... 332
Overview
VIVOTEK IZ9361-EH is an H.265 outdoor-ready network camera with 150m IR illuminators and a
20x optical zoom lens, providing a superb low light image for the most challenging situations. By
adopting VIVOTEK’s latest IR technology, VAIR (Vari-Angle IR), allows IZ9361-EH to automatically
adjust the IR angle to the optical zoom delivering consistent IR images in all elds of view.
The IZ9361-EH also features VIVOTEK’s sophisticated Smart Stream II technology. This enables it
to optimize quality for desired regions, therefore maximizing bandwidth efciency.
By combining H.265 compression technology and VIVOTEK’s Smart Stream II technology, users
can obtain bandwidth savings of up to 80%* compared to traditional H.264 systems.
Additionally, in order to ensure full protection against both harsh environments and acts of
vandalism, the IZ9361-EH is specifically designed with an IP67-, NEMA 4X- and IK10-rated
housing, with a wide temperature range from -50°C to 60°C making it suitable for all outdoor
surveillance applications such as highway trafc monitoring, city surveillance, and harbor patrol.
* Depending on scene being monitored.
Revision History
■ Rev. 1.0: Initial release.

VIVOTEK
4 - User's Manual
Read Before Use
The use of surveillance devices may be prohibited by law in your country. The Network Camera
is not only a high-performance web-ready camera but can also be part of a exible surveillance
system. It is the user’s responsibility to ensure that the operation of such devices is legal before
installing this unit for its intended use.
It is important to first verify that all contents received are complete according to the Package
Contents listed below. Take note of the warnings in the Quick Installation Guide before the Network
Camera is installed; then carefully read and follow the instructions in the Installation chapter to
avoid damage due to faulty assembly and installation. This also ensures the product is used
properly as intended.
The Network Camera is a network device and its use should be straightforward for those who
have basic networking knowledge. It is designed for various applications including video sharing,
general security/surveillance, etc. The Configuration chapter suggests ways to best utilize the
Network Camera and ensure proper operations. For creative and professional developers, the URL
Commands of the Network Camera section serves as a helpful reference to customizing existing
homepages or integrating with the current web server.
Package Contents
■ IZ9361-EH and wall-mount bracket
■ Sunshield, hex L wrench x2, T25 L wrench x1, desiccant bag, screws
■ M16 waterproof cable gland x1 (other M20 glands pre-installed - for Ethernet and DI/DO).
■ Sun shield and screws c
■ Software CD
■ Quick Installation Guide & alignment sticker
* T8 key wrench is also used for the hex socket screw on the camera bracket.
NOTE:
Use the camera only with a DC power supply that is UL listed, and limited power source
(LPS) certied. The power supply should bear the UL listed and LPS marks. The power
supply should also meet any safety and compliance requirements for the country of use.
The T and RT models have auto-focus motorized lens. Some of the sufx syntax used in
model naming are listed below:
E w/ heater for extreme weather
Fx Focal length w/ number
T w/ Remote focus lens
R w/ PoE repeater
H w/ High Dynamic Range functionality
NOTE:

VIVOTEK
User's Manual - 5
Symbols and Statements in this Document
i
INFORMATION: provides important messages or advices that might help prevent
inconvenient or problem situations.
NOTE: Notices provide guidance or advices that are related to the functional integrity of
the machine.
Tips: Tips are useful information that helps enhance or facilitae an installation, function,
or process.
WARNING: or IMPORTANT:: These statements indicate situations that can be
dangerous or hazardous to the machine or you.
Electrical Hazard: This statement appears when high voltage electrical hazards might
occur to an operator.
Physical Description
Front View
IMPORTANT:
If powered by PoE, the IZB9361-EH comes with an embedded heater requires an
UPoE switch or injector. The applicable VIVOTEK PoE models are listed below.
Model
AW-IHU-0100, AW-IHU-0200, AW-IHU-0600, AP-GIC-010A-060, AW-GEU-080A-250
VAIR IR lights
Waterproof cable glands
Lens

VIVOTEK
6 - User's Manual
Ethernet 10/100 RJ45 Plug
Rear View
GND
MIC IN
GND
LINE OUT
MicroSD
Reset
LEDs
DO+(12V)
DO-
DI0
DI1
DI2
DI-
RS485-
RS485+
GND/AC24V-
DC24V+/AC24V+
Ethernet
• These devices(IR LED) emit highly concentrated infrared light, which view
angle(range) is smoothly varied depending on operation mode. To avoid risk of eye
injury, please do not look directly at the LEDs at a near distance and remember to use
the camera live view to check if the IR illumination is active.
WARNING:

VIVOTEK
User's Manual - 7
DI/DO Diagram
DI-
DO+
DI+
DO- External
power source
VDC
Switch
BJT transistor
Relay
AC
Source
NO NC
External
device
DI-
DO+
DI+
DO-
VDC
Switch
BJT transistor
Relay
AC
Source
NO NC
External
device
1. The DO+ pin provides different output voltages depending on the camera model, 12V for
this model, and the max. load is 50mA.
2. The max. voltage for DO- pins is 80VDC (External power).
In order to control AC devices, the above diagram can be taken in consideration. The
diagram uses a relay to control the ON/OFF condition of the AC device.
3. An external relay can be triggered by using DO+ or by an external power source,
depending on the type of relay you use.
4. In case of using an individual relay (instead of using a relay module), for protection
against voltage or current spikes, a transient voltage suppression diode must be
connected in parallel with the inductive load.

VIVOTEK
8 - User's Manual
Hardware Installation
2.Attach the included alignment sticker to a preferred location. Drill holes for mounting
screws and if applicable, drill a cabling hole.
0002D10766AD
XXXXXX
1.Jot down the camera's MAC address for later reference.

VIVOTEK
User's Manual - 9
3.Route cables through the routing hole and the wall mount bracket.
4. Secure the bracket to wall using the included screws.

VIVOTEK
10 - User's Manual
5. Remove the rear cover using the T25 wrench.
GND
MIC IN
GND
LINE OUT
MicroSD
Reset
LEDs
DO+(12V)
DO-
DI0
DI1
DI2
DI-
RS485-
RS485+
GND/AC24V-
DC24V+/AC24V+
Ethernet
Refer to the diagram below for the pinouts and the cable guage range.
Cable Gauge
Name Wire gauge Current
1 DI/DO 1~1.5mm 300mA
2 Audio IN/OUT 2.2~2.8mm 300mA
3DC24V & AC24V 1.3~1.8mm 2.5A
4 Ethernet 4.3 ~ 6mm -

VIVOTEK
User's Manual - 11
6. Pass the Ethernet and I/O cables through the waterproof cable gland. Pass the cables
through and rubber seal and properly install the components of the cable gland.
7. Insert the cables into the canister, connect cables to the connectors inside, and install
the waterproof cable glands to the canister.

VIVOTEK
12 - User's Manual
8. Replace the desiccant bag on the rear cover. The desiccant bag comes with an adhesive
tape.
1
2
9. Install the rear cover.

VIVOTEK
User's Manual - 13
10. 10-1. Push the spring mortise.
10-2. Hook the notched bracket onto the groove within the spring mortise.
1
2
11. With the camera sitting on the bracket, secure the connection by fastening another two
hex socket screws on the other side.

VIVOTEK
14 - User's Manual
12. Loosen the hex socket screw at the bottom of the bracket, and then turn and aim the camera
at the preferred direction. Adjust the shooting direction and tilt angle. When done, tighten the
screw.
1
2
13. Install the sun shield by fastening 4 retention screws.

VIVOTEK
User's Manual - 15
24V 2A/3.5A
AW-IHU-0100
AW-IHU-0200
AW-IHU-0600
AP-GIC-010A-060
AW-GEU-080A-250
60W output / port
- OR -
The camera can be powered either by a DC/AC 24V 3.5A power adaptor or by a PoE
switch. If powered by PoE, make sure the PoE switch can deliver a 60W output per port
to drive the IR lights and heater in a low temperature environment.

VIVOTEK
16 - User's Manual
14. Install the "Installation Wizard 2" software utility on your software CD.
15. The program will search for VIVOTEK Video Receivers, Video Servers or Network
Cameras on the same LAN.
16. Double-click on the camera's MAC address to open a browser management session
with the camera.
17. With a live view is displayed on your laptop, adjust to obtain an optimal image. Check
the live view to ensure the image is in focus.
LED Denitions
Item LED status Description
LED De`nitions
1 Steady Red Powered and system booting, or network
failed
Red LED off Power off
Green LED off Network is disconnected
2 Steady Red and Green LED blinks every 1
sec.
Connected to network
3Green LED blinks every 1 sec. and RED
LED blinks consecutively every 0.15 sec.
Upgrading rmware
4Green and RED blink every 0.15 sec, Green
and RED light on, then blink again.
Restoring defaults
5RED LED is on, Green LED blinks and RED
LED is constantly on.
Status after a reset (network connected)
Green and RED LEDs are constantly on. Status after a reset (network
disconnected)
0002D1730202
00-02-D1-73-02-02 192.168.5.151 FD8168
IW2
Browser
LAN

VIVOTEK
User's Manual - 17
Hardware Reset
The reset button is used to reset the system or restore the factory default settings.
Sometimes resetting the system can return the camera to normal operation. If the system
problems remain after reset, restore the factory settings and install again.
Reset: Press the recessed reset button. Wait for the Network Camera to reboot.
Restore: Press and hold the reset button until the status LED rapidly blinks. Note that all
settings will be restored to factory default. Upon successful restore, the status LED will
blink green and red during normal operation.
SD/SDHC/SDXC Card Capacity
This network camera is compliant with SD/SDHC/SDXC 16GB / 8GB / 32GB / 64GB /
128GB and other preceding standard SD cards. Class 6 or higher speed modules are
recommended.
Reset Button

VIVOTEK
18 - User's Manual
Network Deployment
NOTE:
1. The camera is only to be connected to PoE networks without routing to outside plants.
2. For PoE connection, use only UL listed I.T.E. with PoE output.
Internet connection via a router
Before setting up the Network Camera over the Internet, make sure you have a router and follow
the steps below.
1. Connect your Network Camera behind a router, the Internet environment is illustrated below.
Regarding how to obtain your IP address, please refer to Software Installation on page 20 for
details.
IP address : 192.168.0.3
Subnet mask : 255.255.255.0
Default router : 192.168.0.1
IP address : 192.168.0.2
Subnet mask : 255.255.255.0
Default router : 192.168.0.1
LAN (Local Area Network)
Router IP address : 192.168.0.1
WAN (Wide Area Network )
Router IP address : from ISP
Cable or DSL Modem
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
Internet
2. In this case, if the Local Area Network (LAN) IP address of your Network Camera is
192.168.0.3, please forward the following ports for the Network Camera on the router.
■ HTTP port: default is 80
■ RTSP port: default is 554
■ RTP port for video: default is 5556
■ RTCP port for video: default is 5557
If you have changed the port numbers on the Network page, please open the ports
accordingly on your router. For information on how to forward ports on the router, please refer
to your router’s user’s manual.
3. Find out the public IP address of your router provided by your ISP (Internet Service Provider).
Use the public IP and the secondary HTTP port to access the Network Camera from the
Internet. Please refer to Network Type on page 69 for details.

VIVOTEK
User's Manual - 19
Internet connection with static IP
Choose this connection type if you are required to use a static IP for the Network Camera.
Please refer to LAN setting on page 68 for details.
Internet connection via PPPoE (Point-to-Point over Ethernet)
Choose this connection type if you are connected to the Internet via a DSL Line. Please refer to
PPPoE on page 69 for details.
Congure the router, virtual server or rewall, so that the router can forward any data coming
into a precongured port number to a network camera on the private network, and allow data
from the camera to be transmitted to the outside of the network over the same path.
From Forward to
122.146.57.120:8000 192.168.2.10:80
122.146.57.120:8001 192.168.2.11:80
... ...
When properly congured, you can access a camera behind the router using the HTTP request
such as follows: http://122.146.57.120:8000
If you change the port numbers on the Network conguration page, please open the ports ac-
cordingly on your router. For example, you can open a management session with your router to
congure access through the router to the camera within your local network. Please consult your
network administrator for router conguration if you have troubles with the conguration.
For more information with network conguration options (such as that of streaming ports),
please refer to Conguration > Network Settings. VIVOTEK also provides the automatic port for-
warding feature as an NAT traversal function with the precondition that your router must support
the UPnP port forwarding feature.

VIVOTEK
20 - User's Manual
Software Installation
Installation Wizard 2 (IW2), a software included in the product CD, helps you set up your
Network Camera on the LAN.
1. Install IW2 under the Software Utility directory from the software CD.
Double-click the IW2 shortcut on your desktop to launch the program.
2. The program will conduct an analysis of your network environment.
After your network environment is analyzed, please click Next to continue the program.
0002D1730202
00-02-D1-73-02-02 192.168.5.151 IZ9361
Installation
Wizard 2
IW
2
Network Camera
Model No: IZ9361
Made in Taiwan
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Pat. 6,930,709
MAC:0002D1730202
R o H S
3. The program will search for all VIVOTEK network devices on the same LAN.
4. After a brief search, the installer window will prompt. Click on the MAC and model name
that matches the one printed on the product label. You can then double-click on the address
to open a management session with the Network Camera.