Vivreau Vi1 Training manual

7J5BQSystem Commissioning
1
Vi1 and Vi1H
VIVREAU VITAP SYSTEM
COMMISIONING INSTRUCTIONS
Confirm that the proper services are available. The water supply must be a ½” water line with a
½” threaded ball valve female end. Anything smaller than ½” is not acceptable and should
never be used. The electrical outlet must be within the range of the power cord of the
machine, extension cords should never be used. CO2 is also provided by the customer in either
a tank or with a line from a bulk or remote system. If connecting to an existing system the
customer must provide a ¼” barbed shutoff within 40” of the installation. Check for proper top
and bottom ventilation, drain and countertop holes.
If any of the required services are missing/incorrect or if you have any questions regarding the
commissioning instructions, please call 877-999-1044 option #5, and someone from our Tech
Support Team will provide further instructions.
Open packaging and check for any damage, check that all parts are included by using the
supplied diagram. Do not make any connections yet.
-BZPVUBMMDPNQPOFOUTJOTJEFUIFDBCJOFUUPDPOGJSNTQBDJOHBOEQPTJUJPOJOH
PGFRVJQNFOU5IFVivreau logoPOUIF NBJOVOJUTIPVME GBDF PVU BOE CF WJTJCMFInstall the ViTap Font using supplied installation kit.
Connect Water line to street water outlet usingsupplied kit and diagram.
"MMXBUFSBOEGJMUFSDPOOFDUJPOTTIPVMECFNBEFVTJOHUIFTVQQMJFEEJBHSBN8BUFS
TVQQMZNVTUCFTVQQMZFill chiller water tank CZSFNPWJOHUIFGSPOUQMVHBOEVTJOHUIFDPMEXBUFS
TVQQMZMJOF'JMMVOUJMXBUFSSVOTCBDLPVUPGUIFGJMMUVCF-FUBMMSFTJEVBM
XBUFSFYJUUIFGJMMUVCFCFGPSFSFQMBDJOHUIFQMVHConnect street water pipe to the machine and insulatethe pipeGVMMZCVU EPOPU turn UIFwater
on just yet. A minimum water supplyof 55psi should be supplied to the machine or
thedispense operation will become slow and may need
abooster pump.
*If installing a Vi1H water connections to the Mavea filter should be made now. Be sure to flush
10 liters of water through the filter before connecting to the boiler. Connect the Mavea filter to
the boiler using the supplied parts and diagram.
vivreauwater.com
Tel: [phone] (Option #5 for Tech Support)

Bottling System Commissioning
2
Bottling System Commissioning 7J5BQSystem CPNNJTTJPOJOH
2
vivreauwater.com
Tel: [phone] (Option #5 for Tech Support)
Insulate and connect the 5/16” line from the ViTap to the main unit using the supplied John
Guest Fitting. *If installing a Vi1H now connect the hot water line from the boiler to the ViTap
using the silicone tubing and clamps, cut as needed.
Connect the wire harness and ground wire from the ViTap to the main unit. *If installing a
Vi2H connect the wire harness from the main unit to the boiler. For the Vi2 model the boiler
wire harness is not used and should be left as is.
Connect the ViTap drain to the customer supplied drain.
Hang provided “Do Not Use” sign on the tap.
Remove the 3M filter and fill the service cartridge (located in Vivreau Tech Kit) with 2ml BTF
Idopher using the provided syringe (wear safety glasses) and connect to the filter head. Now
turn on the water supply.
*The boiler power light should be bright green. The ready light should be light green now and
bright green once temperature has been reached. Refer to the boiler manual for additional
information.
Press and hold the Still button (blue) and dispense until sanitizing solution appears, release
the still button.
Check for leaks on all fittings.
Allow for sanitizing solution to be in the system for no less than 10 minutes before flushing at
least 5 liters of water from the Still water.
Turn off the water supply and press the Still button until the water stops running, release the
button. Remove the service cartridge and refit the 3M filter. Turn the water supply back on.
Touch the Still button and flush water through until it runs clear and no air bubbles can be
seen.
Water should now be fully flushed and free of sanitizing solution and air bubbles. Visually
check and taste test the water. Repeat flushing if needed.
These procedures should take around 1 hour and you should notice the water temperature
getting colder depending on the surrounding ambient temperature.

3
7J5BQ4ZTUFNCommissioning
3
vivreauwater.com
Tel: [phone] (Option #5 for Tech Support)
*Vi1h Only. Check that the boiler has now reached temperature. The ready light should now
be bright green.
*Caution the hot water feature dispenses hot water near boiling temperatures. Use care
flushing hot water to avoid burns.
*Flush 2 liters of hot water from the tap by pressing the hot (red) button once and pressing
and holding the opposite hot button.
Check once more for leaks.
Check the condenser air grill is clear and has adequate air flow.
Make sure the surfaces are clean, water is taste tested, and all functions are fully
tested before training the customer on using the ViTap.
Remove “Do Not Use” sign.
Make sure to completely fill out the Vivreau Installation Checklist recording all
information needed, including the serial number and accurate system location.