ViziT ML300M User manual

VIZIT-ML300
VIZIT-ML300
SPECIFICATIONS
V9…15
7.2
OPERATI CONDITIONS
-40C +45C
98% 25C
SAFETY INSTRUCTIONS
VIZIT-ML300M
VIZIT-ML300M-40
VIZIT-ML300M-50
M
M contains a degaussing module sealed together with electromagnet’s coil.
VIZIT-ML300M
VIZIT-ML300M-40
VIZIT-ML300M-50
DC
kg 300 ± 60
W
mm
kg
VIZIT-ML300M 2.5
VIZIT-ML300M-40 2.8
VIZIT-ML300M-50 3.0
NG
PARTS LIST
15 VDC
INSTALLATION
1-3
4
Electromagnetic lock is (30 to 50 mm thick)
. ock on door open out .
oltage, :
Holding force (U=12V)
Power consumption, (U=12V):
:
Ambient temperature range: up to
Relative humidity of air: up to at .
h
.
used to lock an entrance door as part of an access control
system The l is installed inside the building, a that s wards The lock should be used together with a
door closer.
The following versions are available:
-;
-;
-.
Operating v
,
Dimensions,
Weight, :
-
-
-
T e lock does not contain voltage above .
Do not make any connections or repair when the power is on.
The lock should be installed inside the building according to directions on Figures
The armature plate is to be fixed on the door. The electromagnet is to be fixed on the door frame opposite to the
armature plate. Electromagnet’s work surface is shown on Figure .
To ensure maximum holding force the armature plate should be fixed as close to the door edge as possible, taking into
account electromagnet’s position.
Note: It is more convenient to make markings for electromagnet and armature plate installation, if the door is closed.
Lock parts
Electromagnet
Armature plate
Width Height Depth
188 55 35
126 55 12
Title VIZIT-ML300M-40 VIZIT-ML300M-50
Electromagnet
Armature plate
1 ( 40х40 мм)Fastening kit angle bar
Fastening kit 2 angle bar( 50х50 мм)
Fastening kit for armature plate mounting()
1
1
1
1
1
1
Package
Operating instruction
-
1
1
1
1
1
VIZIT-ML300M
1
1
1
-
-
1
1
1-
Fastening kit plate bar3 ( ) 1--

Installation order:
Make holes for the armature plate and guide pin
Fix the armature plate on the inner side of the door, using fastening kit (Figure ).
Leave 4..5mm clearance between the plate and door surface.
Where the door leaf is 50 to 60 mm wide, use screws g (not supplied).
the plate bar / angle bar on the door frame with screws (1) as in Figures . Do not fasten the screws very tight, so
that you could further adjust the plate bar / angle bar position, if needed.
Fix the electromagnet on the plate bar / angle bar with screws (3)
Adjust the electromagnet with plate bar / angle bar to ensure the closest fitting of the electromagnet’s work surface to
the armature plate
Remove the electromagnet off the plate bar / angle bar.
Tighten the screws (1, 2) to securely fix the plate bar / angle bar on the door frame.
Fix the electromagnet on the plate bar / angle bar
Lock’s terminals have no polarity. The example of wiring diagram is given on Figure . The controlling device can be a
doorstation, control unit, RF-controller etc.
Program your controlling device to the lock type as electromagnetic, and its unlocked state duration (if the functions are
supported), following directions in the operating instruction on the controlling device used. Note, that the lock is released
when voltage across its terminals is off.
Requirements for wires and more wiring examples are given in the controlling device operating instruction.
After installation and wiring complete, check your lock for proper mounting and operation.
At s ching the controlling device’s power , the e s the a (the lock is closed). Check if
the lock is closed securely and firmly keeps the door shut.
Perform unlocking as described in the controlling device operating instruction. Check if the electromagnet releases the
armature plate without any obstructions.
1. .
2.
2.М6-6 х45.36.019
3. Fix
4. .
5.
.
6.
7.
8. .
wit on lectromagnet attract rmature plate
1
2, 3
CONNECTION AND FUNCTIONAL
5
CHECK
2
3
1
Electromagnet
2
Plate bar
Figure Lock mounting
using plate bar
2 – Figure Lock mounting
using angle bar
3–
Figure Armature plate mounting1–
Armature plate
Nut
Door leaf
Door frame
Screw
Spacer (not supplied, optional order)
Washer
Rubber washer
2
1
Angle bar
3
Electromagnet
Screw nut

Electromagnet’s
work surface
Figure 5 Wiring diagram-
Power supply
unit
9…15 V
Lock
VIZIT-ML300M
Controlling
Device
NO
COM
NC
Figure 4 - Electromagnet’s
work surface