Vode BoxRail 907 User manual
Installed View
®
Adaptive architectural lighting systems
Technical Support: 707-996-9898
BoxRail®| 907 | Remote Power
Please read instructions in their entirety before proceeding with any part of the installation. This product must be installed in accordance with the applicable installation
code by a person familiar with the construction and operation of the product and the hazards involved. Consult a qualified electrician to ensure correct branch circuit rating.
To prevent electric shock, disconnect all power before installing or servicing product. Rated for use in dry and damp locations only. Retain instructions for future reference.
© 2018 Vode Lighting LLC. All rights reserved. | 21684 8th Street East, Suite 700, Sonoma, CA 95476 | 707.996.9898
BoxRail | 907 | Installation Guide | October 2018 | Rev A • 1
BoxRail | 907
907-BX-XX-...-YY
907 | BoxRail with Side Feed
Rotate 2 (R2B)
- Page 6
Rotate 1 (R1B)
- Page 5
Fixed 1 (F1S)
- Page 4
Parts DiagramTable of Contents
© 2018 Vode Lighting LLC. All rights reserved. | 21684 8th Street East, Suite 700, Sonoma, CA 95476 | 707.996.9898
BoxRail | 907 | Installation Guide | October 2018 | Rev A • 2
907-BX-XX-...-YY
907 | BoxRail with Back Feed
BK-907-BX-SR1-YY
Surface Mount 203° Rotating Bracket
BK-907-BX-S1-YY
Surface Mount Fixed Bracket
BK-907-BX-SR2-YY
Surface Mount 49° Rotating Bracket
WRH-MWP-XX-M-18/2-YY
2-Conductor Wire Harness
(25’ standard)
Installation Instructions
Install Remote Power Supply
IMPORTANT! Before installing power supply, turn off electricity at circuit box.
Install power supply housing to desired surface using screws (provided by others). Run
line voltage wiring into power housing through knockout and secure with 1/2" NPT fitting.
Ground housing by connecting ground/earth to green slot in the quick-connect. Connect
common/neutral to white slot in quick connect and line/hot to black slot in quick
disconnect.
Feed low voltage wire harness into remote power housing. Connect wire harness to
power supply using Red (+) and Black (-) leads. Leave approximately 1" of wire harness
hanging out of Micro J-Box or other hole.
DO NOT power on system until the installation is complete.
For remote power supply maximum distance or other wiring questions, please consult
Vode Driver Guide.
WRH-MWP-XX-M-18/2-YY
18 gauge, multi-strand
plenum rated wire harness
Conduit Fittings
(provided by others)
L
N
Line Voltage Connection
Quick connect provided for
line voltage connection
LED output 1
+
-
LED output 2
+
-
LEDcode
NTC
+
-
To LED
DO NOT USE
Example Only
See Vode Driver Guide for wiring detail.
Fixture Orientation
Power feed comes out the bottom of the fixture (as shown) and is located 3” (76 mm)
in from the end of the fixture.
NOTE: For 85° optics, power feed is located on the left side of the fixture, when
facing the illuminated surface.
© 2018 Vode Lighting LLC. All rights reserved. | 21684 8th Street East, Suite 700, Sonoma, CA 95476 | 707.996.9898
BoxRail | 907 | Installation Guide | October 2018 | Rev A • 3
BoxRail | 907
Fixed 1 (F1S)
Fixture wire harness comes out the
side of the fixture, approximately 3”
from the right end, as the light faces
away from the user. For the 85°
Asymmetric optics, the light will
always be emitted from the far side
of the wire harness.
Rotate 2 (R2S)
Fixture wire harness comes out the
side of the fixture, approximately 3”
from the right end, as the light faces
away from the user. For the 85°
Asymmetric optics, the light will
always be emitted from the far side
of the wire harness.
Rotate 1 (R1B)
Fixture wire harness comes out the
bottom of the fixture, approximately
3” from the right end, as the light
faces away from the user. For the
85° Asymmetric optics, the light will
always be emitted from the far side
of the wire harness.
Fixed 1 (F1S)
Each rail is pre-installed with two adjustable mounting brackets that can be secured in
place using the provided set screws. It is recommended that they are positioned
approximately 3” in from the end. Vode recommends using the provided minimum spacing
measurements to ensure the fixture can install properly.
Using #8 flat head screws, provided by others, position fixture and screw to desired
mounting surface.
NOTE: Be careful with fixture orientation for the 85° Asymmetric Fixture. For 85° optics,
power feed is located on the left side of the fixture, when facing the illuminated surface.
See page 3 for more information.
Installation Instructions
Connect fixture to
provided Wire
Harness
use #8 screws
(provided by others)
© 2018 Vode Lighting LLC. All rights reserved. | 21684 8th Street East, Suite 700, Sonoma, CA 95476 | 707.996.9898
BoxRail | 907 | Installation Guide | October 2018 | Rev A • 4
1.28”
(33 mm)
1.6”
(42 mm)
Side View
Use these minimum measurements to ensure
your mounting location will be sufficient
Top View
Provided
5/64” (2 mm)
set screws
BoxRail | 907
Rotate 1 (R1B)
Each rail is pre-installed with two adjustable mounting brackets that can be secured in
place using the provided set screws. It is recommended that they are positioned
approximately 3” in from the end. Vode recommends using the provided minimum spacing
measurements to ensure the fixture can install properly.
Rotate the bracket open to allow access to the mounting hole. Using #8 flat head screws,
provided by others, position fixture and screw to desired mounting surface. Rotate the
fixture into the desired position and use the provided set screws to lock in place.
NOTE: Be careful with fixture orientation for the 85° Asymmetric Fixture. For 85° optics,
power feed is located on the left side of the fixture, when facing the illuminated surface.
See page 3 for more information.
Installation Instructions
© 2018 Vode Lighting LLC. All rights reserved. | 21684 8th Street East, Suite 700, Sonoma, CA 95476 | 707.996.9898
BoxRail | 907 | Installation Guide | October 2018 | Rev A • 5
Side View
Use these minimum measurements to ensure
your mounting location will be sufficient
BoxRail | 907
Connect fixture to
provided wire
harness
use #8 screws
(provided by others)
2.22"
(56 mm)
1.6”
(41 mm)
1.14”
(29 mm)
90°
Provided
1/16” (1.5 mm)
set screw
Provided
1/16” (1.5 mm)
set screw
Rotate 2 (R2S)
Each rail is pre-installed with two adjustable mounting brackets that can be secured in
place using the provided set screws. It is recommended that they are positioned
approximately 3” in from the end. Vode recommends using the provided minimum spacing
measurements to ensure the fixture can install properly.
Rotate the bracket open to allow access to the mounting hole. Using #8 flat head screws,
provided by others, position fixture and screw to desired mounting surface. Rotate the
fixture into the desired position and use the provided set screws to lock in place.
NOTE: Be careful with fixture orientation for the 85° Asymmetric Fixture. For 85° optics,
power feed is located on the left side of the fixture, when facing the illuminated surface.
See page 3 for more information.
Installation Instructions
© 2018 Vode Lighting LLC. All rights reserved. | 21684 8th Street East, Suite 700, Sonoma, CA 95476 | 707.996.9898
BoxRail | 907 | Installation Guide | October 2018 | Rev A • 6
Side View
Use these minimum measurements to ensure
your mounting location will be sufficient
BoxRail | 907
Connect fixture
to provided wire
harness
use #8 screws
(provided by others)
1.27"
(32 mm)
1.66"
(42 mm)
1.81"
(46 mm)
2.1"
(53 mm)
48°
Provided
1/16” (1.5 mm)
set screw
Provided
1/16” (1.5 mm)
set screw
My fixture will not turn on:
Check all wiring is correct and all connections are fastened properly.
If all wiring is correct, remove fixture and connect it to a known working driver.
If the fixture lights up, then the problem is with the installed driver or wiring:
1) Check line voltage to driver is present.
2) Check driver wiring (see Vode Driver Guide for details) and check wiring to
fixture.
3) Check driver and dimming system are compatible (see Vode Dimmer
Guide and the dimmer manufacturer's website).
If fixture still doesn't light up, check that all dimming wires are installed
correctly. Reversed polarity on any driver will cause the entire system to not
work, (see Vode Driver Guide for wiring details).
The fixture is not dimming properly:
Check all wiring is correct and all connections are fastened properly.
Check driver wiring (see Vode Driver Guide for details). Make sure driver is
compatible with dimming controls (see Vode Dimmer Guide and the dimmer
manufacturer's website).
Trouble Shooting Guide
For any help with installation or technical information,
contact Vode Tech Service at 707-996-9898.
Listed to UL standards for damp location by a Nationally Recognized Testing
Laboratory (NRTL) recognized by OSHA
Operating Temperature: 32°F to 104°F (0°C to 40°C).
Input Voltage: 120v - 277v, 50/60hz.
Power Type: Class 2 (<60v) constant current driver.
Dimming curve is factory preset to linear. Logarithmic is available upon
request. See Vode Driver Guide for specific details and wiring diagram.
Unless specified, one driver per rail will be supplied.
5 Year Limited Warranty. All material and component parts manufactured by
Vode are guaranteed to be free from defects of material and/or workmanship
for a period of 5 years from date of sale. Product must be installed according
to Vode installation instructions and accepted trade practices. Power supplies
and other auxiliary equipment is not covered under Vode warranty but may be
covered by separate OEM warranty.
Appendix
Important Notes
Remote DistanceDriver
72’ (21.9 m)
32’ (9.8 m)
16’ (4.88 m)
Zipper board: Standard / Low Output: 30' (9.14 m),
High Output: 15' (4.57 m)
Button board: Standard / Low Output: 15' (4.57 m)
High Output: 10' (3.05 m)
EldoLED
Philips
OSRAM
Lutron
Note: All Vode remote drivers come in a 1/16” (0.8mm) formed steel, zinc chromate
plated power supply housing with six (6) knockouts for 1/2" NPT fittings. Power
supply housing dimensions: 1.9” (48.3 mm) x 1.9” (48.3 mm) x 24.5” (622.3 mm)
Remote Driver Distance
For other wiring questions, see Vode Driver Guide.
-
-
-
-
-
-
-
-
BoxRail | 907
© 2018 Vode Lighting LLC. All rights reserved. | 21684 8th Street East, Suite 700, Sonoma, CA 95476 | 707.996.9898
BoxRail | 907 | Installation Guide | October 2018 | Rev A • 7
Table of contents
