Sunricher SRP-2309-75-TW-CC User manual

1 Subject to change without noce. Informaon without guarantee. / 08.01.2021
SRP-2309-75-TW-CC
75W DALI DT8 DIMMABLE LED DRIVER
Product features
• DT8 dimmable 4-channel RGBW power supply unit
• 100-277VAC wide input voltage range
• 2-channel constant current output (total output power up to 75W)
• Output current from 250mA to 1500mA selectable via DIP switches
• Class 2 power supply, completely insulated plasc housing
• High power factor and eciency
• Built-in DALI interface, DALI DT8 device, the device can be controlled via a DALI address
• Colour control according to DALI DT8 specicaons
• Complies with DALI IEC 62386-209-:2011 standard
• Generally compable with DALI masters supporng DT8 commands
• IP20 protecon class, suitable for indoor lighng projects
• 5 years warranty

2 Subject to change without noce. Informaon without guarantee. / 08.01.2021
Technische Daten
INPUT
Voltage Range 100-277VAC
Frequency Range 50/60Hz
Power Factor (typ.) >0.96@230VAC
Total Harmonic Distoron THD ≤ 15% (@ full load /230VAC)
Eciency typ. 87% @ 230VAC full load
AC Current (typ) 400mA @ @ 230VAC
Inrush Current (typ) Cold start max. 20A@230VAC
Leakage Current < 0.5mA/230VAC
Stand by Power Consumpon 0.5W
OUTPUT
LED Channel 2
Setable current:
250mA, 300mA, 350mA, 400mA. 500mA, 700mA, 800mA,
900mA, 1000mA, 1100mA, 1200mA, 1300mA, 1400mA,
1500mA
Current Tolerance +/- 5%
DC Voltage Range 6-48VDC
Rated Power max. 72W /CH, CH1+CH2≤75W
PROTECTION
Short Circuit Yes, recovers automacally aer fault condion is removed
Over Temperature Yes, recovers automacally aer fault condion is removed
Over Voltage Yes, recovers automacally aer fault condion is removed
CONTROL
Dimming Interface DALI DT8
Dimming Range 0.1% - 100%
Dimming Methode PWM, 1.5kHz
Dimming Curve Logarithmic
ENVIRONMENT
Working Tempetrature -20°C - + 45°C
Max. Case Temperature 85°C
Working Humidity 10%-95% RH non-condensing
Storage Temperature -40°C - +80°C
Storage Humidity 10% - 95% RH
IP Rang IP20 (suitable for indoor LED lighng applicaons)
Safety & EMC
Safety Standards
UL8750, CAN/CSA C22.2 No. 250.13-14, ENEC EN61347-1,
EN61347-2-13 approved
DALI Standards Comply with IEC 62386-209:2011
Withstand Voltage I/P-O/P: 3.75KVAC
Isolaon Resistance I/P-O/P: 100M Ohms / 500VDC / 25°C / 70% RH
EMC Emission EN55015, EN61000-3-2, EN61000-3-3
EMC Immunity EN61547, EN61000-4-2,3,4,5,6,8,11, , surge immunity Line-
Others
MTBF 193.6K hrs min. @ 230VAC full load and 25°C ambient tempe-
rature
Dimension 244 x 64 x 32mm
Warranty 5 years

3 Subject to change without noce. Informaon without guarantee. / 08.01.2021
Product dimension
Wiring diagram

4 Subject to change without noce. Informaon without guarantee. / 08.01.2021
Installaon
Operaon
• Approved wire diameter: AWG16—AWG20 / 0.5mm2-1.5mm2
Set DALI address manually via buons
1. Press one of the two buons unl the LED display starts ashing.
2. Press one of the two buons briey to change the corresponding number unl the desired number
lights up. Use the le buon to change the number by 10 units, the right buon to change the num-
ber by 1 unit. The address can be set from 00-63.
3. Then press one of the two buons unl the display stops ashing.
Informaon: The DALI address can be set manually from 00-63-FF. No DALI address is assigned in the
factory seng. The display shows FF. If the unit is manually set to FF, it is reset to the factory seng.
Assigning a DALI address via a DALI master
The DALI address can also be programmed automacally via a master. Please refer to the operang instruc-
ons of the respecve DALI master.
Informaon: The display will show AU if the DALI Master assigns the address to the device.
If an address is set, all four channels are controlled via this address. If, for example, the dimmer is pro-
grammed to address 22 (visible on the display), CH1, CH2, CH3 and CH4 are controlled via this address.
SAFETY AND WARNINGS
• Do not install with power applied to the device
• Do not set operaon current with power applied to the device
• Do not expose the device to moisture
• Drivers with PWM dimming can cause noise due to vibraons. These can be generated by vibra-
ng components in the device as well as by resonant vibraons from other bodies.

5 Subject to change without noce. Informaon without guarantee. / 08.01.2021
Important Informaon for installaon
Power on level is a DALI parameter that denes the level of a control gear aer power is restored. The factory
default power on level for this driver is 100, which means the driver will be at 100% intensity when power is resto-
red.
Troubleshoong Help
Situaon A: The power supply has been overloaded and is now in overload protecon mode.
What does the error paern look like?
The connected LEDs ash. You can reduce the brightness via a DALI soware and the strip will stop ashing. You can
no longer control the colours with the soware.
How can the problem be solved (two variants A + B)?
A. 1. Disconnect the device from the mains for at least 10 minutes. The unit will reset to factory sengs.
2. Reduce the load so that it meets the specicaons of the unit.
3. You can now operate the unit normally again.
B 1. Disconnect the device from the mains for at least 10 minutes. The unit will reset to the factory sengs.
2. Disconnect the load (LED strip / LED module) from the power supply.
3. Reconnect the device to the mains.
4. Connect the device to the DALI Master soware.
5. In the soware, reduce the Power On Level and the maximum level for this device. The value must be below
the maximum load of the power supply.
6. Disconnect the device from the power supply and reaach the load.
7. You can now operate the device normally again.