Volvo 31285222 User manual

Instruction No Version Part. No.
30756303 1.5 31285222
Navigation system, portable
IMG-279043
Instruction No Version Part. No.
30756303 1.5 31285222
Navigation system, portable
IMG-279043
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 1 / 67

Equipment
A0000162 IMG-282403 IMG-246925 IMG-239660 IMG-239667 IMG-239681
IMG-240673 IMG-239942 IMG-240675
IMG-279044
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 2 / 67

IMG-213320
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 3 / 67

INTRODUCTION
Read through all of the instructions before starting installation.
Notifications and warning texts are for your safety and to
minimise the risk of something breaking during installation.
Ensure that all tools stated in the instructions are available
before starting installation.
Certain steps in the instructions are only presented in the form
of images. Explanatory text is also given for more complicated
steps.
In the event of any problems with the instructions or the
accessory, contact your local Volvo dealer.
Note!
For information regarding the GARMIN device, see
www.garmin.com.
Note!
Some steps in these installation instructions are presented
with illustration only.
Note!
Sections 1-62 apply to cars without loudspeaker grilles.
Sections 63-124 apply to cars with loudspeaker grilles.
Note!
The disc marked A in the kit is used on cars with loudspeaker
grilles.
Applies to cars without loudspeaker grilles
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 4 / 67

1
IMG-296185
Applies to cars without loudspeaker grilles
Assembling the holder
Note!
Take care when handling the components, they are fragile and
are easily damaged.
Take the three screws M5x25 part no. 986957 and nuts from the
kit.
To prevent too great resistance when the nut for the holder is
tightened, hold the screw and screw the nut on and off the
threaded part of the screw. Carry this out on all screws and nuts.
2
IMG-282404
Take special tool 9814104 (torx driver, torx 6), and unscrew the
two screws holding the connector in the holder.
Carefully push the connector to one side with the cable to
expose the bottom of the holder.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 5 / 67

3
IMG-282405
Take the kit with the four spacers from the installation kit.
Carefully pry off the spacer using P/N 31212784. The part
number (1) is on the bottom of the spacer.
4
IMG-282407
Take the three screws and insert them in the spacer fully.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 6 / 67

5
IMG-282408
Apply pieces of butyl tape to the screws so that the screw heads
do not protrude outside the spacer when installing it.
6A
IMG-282406
6B
IMG-282409
Illustration A
Install the spacer in the bottom of the holder.
Illustration B
Ensure that the holder's two screw turrets align between the
small pins in the oblong holes in the spacer. A click should be
heard when the spacer is securely in position.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 7 / 67

7
IMG-282410
Place the connector in the bottom of the hole. The guide hole (1)
in the connector's circuit board must align in the corresponding
pin at the bottom of the holder and the holes (2) in the circuit
board must be over the holder's screw turret.
8
IMG-282411
Take the small torx screws and carefully tighten the connector to
the holder. Ensure that the connector's circuit board is properly
against the screw turret and that there is no play.
Remove the butyl tape from the screws.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 8 / 67

9
IMG-246024
Preparations
Turn the ignition switch to position 0.
Disconnect the battery negative lead.
Note!
Wait at least three minutes before unplugging the connectors
or removing other electrical equipment.
10
IMG-279045
Remove the template from the kit. Cut around the outer lines.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 9 / 67

11
IMG-279046
Place the template with the lower edge 21 mm (53/64") from the
top edge of the air outlet and centred along a line between the
button for the warning flashers and the LED.
Tape the template in position.
12
IMG-279047
Remove the ventilation outlet by carefully inserting special tool
9995919 between the ribs and carefully pulling up the four
catches on the lower edge. Carefully pry using a weatherstrip
tool.
Note!
Pay particular care to the dashboard and the outlet ribs; these
can easily be damaged. The outlet is mounted very firmly.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 10 / 67

13
IMG-279048
Unplug the connector for the warning flashers and move the unit
aside.
14
IMG-279343
Open the glovebox.
Carefully pry off the panel inside the centre console. Use a
plastic weatherstrip tool. The panel is secured by two clips on
each of the short sides.
Pull the panel away downwards.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 11 / 67

15
IMG-263505
Remove the rubber mat and storage compartment.
16
J8504893
Detach the surround around the display and the media player:
Press in the catch at the edge of the media player cover. Use a
small screwdriver. Carefully pry off the surround at the corner.
Use a plastic weatherstrip tool.
Note!
Do not damage the panel and dashboard.
Repeat the operation on the other side.
Hint
If the other side does not detach, press the detached side into
position again and repeat the procedure, beginning from the
other side.
Fold the surround backwards. Remove by pulling upwards.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 12 / 67

17
J8504534
Press out the display module (1) from the reverse of the centre
console. Use both hands and press straight back.
Disconnect the two connectors. Put the display to one side.
18
IMG-263585
Carefully bend loose and remove the hand brake lever's panel.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 13 / 67

19
IMG-270743
Remove the bottom cover.
20
IMG-263588
Applies to cars with manual gearbox
Remove the gear selector lever boot from the center console.
First pry it off at the front edge using a weatherstrip tool and then
unhook it at the rear edge.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 14 / 67

21
IMG-279049
Loosen the gearshift knob from the shift by pressing down the
knob and turning it slight more than a 1/4 turn anticlockwise and
pull it up.
22
IMG-263584
Applies to all models
Remove the two screws.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 15 / 67

23
IMG-279050
Remove the two screws along the front edge of the tunnel
console.
24A
IMG-263586
24B
IMG-263587
Illustration A
Illustration B
Carefully pull up the lock catch with special tool 9995919. At the
same time, slide the whole tunnel console backward so that the
two rear screws in the centre console's panel can be accessed.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 16 / 67

25
IMG-263589
Remove the two screws.
26
J8504535
Remove the two screws holding the centre console to the
dashboard.
Remove the connector on the reverse of the dashboard
environment panel.
Remove the centre console's panel from the dashboard and
tunnel console.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 17 / 67

27
IMG-279051
Remove the two clips securing the cables to the media player by
first pressing them to the sides and then pulling them away
downwards.
Note!
Make sure that the optic cables are not bent or stretched. They
may not be bent with a radius less than 25 mm (1").
28
IMG-279052
Remove the two screws from the bottom of the media player.
Pull out the media player and detach the connectors on the rear
side.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 18 / 67

29
IMG-279053
Cover the opening to the air ducts with paper to avoid chips
filling into these.
Spread out a piece of paper inside the dashboard to catch the
drill chips.
Choose LHD or RHD on the drilling template and mark the holes
in the centre using a scriber.
Take a Ø5mm (13/64") drill bit. Attach a 15 mm (19/32") drill
stop.
Predrill the holes according to the template. Drill square to the
dashboard where the holes are to be positioned.
Note!
Do not damage the dashboard.
30A
IMG-279054
30B
IMG-279243
Illustration A
Select a Ø14 mm (9/16") hole saw.
Swap the central drill bit in the hole saw for a Ø5 mm (13/64")
drill bit. The hole in the holder is larger than the diameter of the
drill bit. Wrap tape around the end of the drill bit to make sure it
sits firmly in place in the hole. Do not lock the central drill bit with
the lock screw. The drill bit must only be used for guiding the
hole saw because the holes in the dashboard's lower part
cannot be larger than Ø5 mm (13/64").
Illustration B
Fit a 9 mm (23/64") drill stop.
Drill out for the cradle's three feet.
Note!
Only drill through the vinyl layer and foam layer, not through
the plastic layer (1) on the lower part of the dashboard as this
will make the hole too large for the nuts that are to be
tightened from underneath.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 19 / 67

31
IMG-280703
Select a Ø25 mm (1/2") hole saw.
Change the centre drill in the hole saw back to the original drill
bit.
Drill for the connection of the connector. Drill through all layers of
the dashboard. Use a 25 mm (1")drill stop.
32
IMG-277332
Use a small screwdriver and clear the three small holes from
any chips so that the underlying plastic layer appears.
Remove the paper from the air ducts and the paper from under
the dashboard. Make sure no chips are left inside the
dashboard.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Navigation system, portable- 30756303 - V1.5
Page 20 / 67