VooDoo ADEL-0200 User manual

SUBARU front ADJUSTABLE sway bar
END LINKs
INSTALLATION INSTRUCTIONs:
13-17 Crosstrek
14-18 forester
10-14 outback
15-20 sti/wrx
06-14 triebca

Part Number:
ADEL-0200
It is recommended the installation of all Voodoo13 parts be completed by an
experienced suspension tuning professional. With proper installation and maintenance,
Voodoo-13 suspension products will provide exceptional performance and durability.
For any questions, please contact Voodoo 13 immediately. Thank you for choosing
Voodoo-13 for your suspension component needs!
NEED HELP?
Representatives are here to help with any questions concerning the operation of this
product.
CALL 480-889-0812
Monday thru Friday 8:30am to 5:30pm MST
RECOMMENDED TOOLS AND SUPPLIES
•General Mechanics Tool Set
•Vehicle Jack and Jack Stands
•Torque Wrench
•14mm Wrench or Socket
•17mm Wrench
PART BREAKDOWN
NOTE: For any OEM hardware please refer to OEM service manual for torque
specifications. For all included hardware please torque to the specifications shown
below. It is recommended to use a torque wrench when tightening instead of an impact
wrench. Apply anti-seize to all hardware threads.

INSTALLATION PROCEDURE
Step 1: Lift the vehicle to a safe height using the recommended factory lift points to work
underneath the front suspension. Ensure placement of safety jack stands where
recommended by the manufacturer's service manual before working underneath the vehicle
(unless using a vehicle lift with safety locks).
NOTE: If you can lift the entire front suspension where the rear wheels are off the ground,
this will ease the process of removing the OEM end links.- If you can only lift one side of the
vehicle, you will need to use a floor jack on the lower portion of the knuckle to relieve the
tension on the sway bar
Step 2: First use a 14mm socket to remove the nut securing the Endlinks to the sway bar
and front lower control arm.
Step 3: Adjust the Voodoo13 end links to the same length as the factory end links by
rotating the threaded heim joint clockwise or counterclockwise. Measurement of the OEM
end links is taken from the center of one ball joint to the other.
Note: Increasing the length of the Voodoo13 end links compared to the OEM end links is an
acceptable way of increasing the spring rate of the sway bar, however, take into
consideration the length of the sway bar does not interfere with any vehicle components
such as the lower control arms or the vehicle chassis. Since Voodoo13 end links are
independently adjustable in length, a preloaded sway bar can improve the corner balancing
of a vehicle with height-adjustable shocks or structs or an uneven suspension ride height.
Step 4: Prepare to install the Voodoo13 end links with the spacers facing the sway bar and
knuckle assembly. Install one hex bolt through the heim joint, spacer, and sway bar. Then
secure with one locking hex nut. Repeat these steps for the opposite side of the vehicle’s
suspension.
Step 5: Once the Voodoo13 end links are installed to the proper length on both the driver
and passenger side of the vehicle, torque the (4) hex nuts to 40 lbf-ft using a torque wrench
while holding the hex bolt heads with a 17mm wrench.

NOTE: With the Voodoo13 end links installed and the vehicle resting on a flat surface, the
sway bar preload can be adjusted
Step 6: Once the desired lengths of the Voodoo13 end links are established, tighten the (4)
jams nuts against the heim joints on both sides of the end link. Properly torque the jams
nuts to 30 lbf-ft using torque wrench.
NOTE: Ensure that all hardware is torqued to the correct specification. Re-check the
hardware torque specification after 50 miles of continuous driving to ensure proper
installation.
WARRANTY
All products sold are subject to the following warranty:
Voodoo13 offers a Limited Lifetime Warranty for our products to the original retail
consumer against defects and workmanship when used on light truck and car
applications under normal operating conditions. This warranty does not apply to parts
that have been improperly installed or wearable items such as, but not limited to, worn
bushings or bearings unless proven to be defective from the manufacturer.
Exterior finish on all Voodoo13 products is not considered a valid warranty; consumers
are responsible for the maintenance of paint, anodize or raw metal finish.
The consumer will be responsible for the removal and freight costs both to and from the
Distributor from which the product was originally purchased. Proof of purchase and
product registration through the Voodoo13 website is mandatory in order to receive
warranty replacement. Original invoice from the Distributor from which the product was
purchased must accompany the product in question for warranty consideration.
Voodoo13 has the right to refuse a warranty claim if procedures are not met by the
original consumer. All returns must have an R.M.A. approval from Voodoo13 prior to
shipping direct to the Voodoo13 facility. Exclusions from this warranty are sales outside
of the United States, the finish, dents, rust, or any condition caused by abnormal use or
neglect.

WARNING
High performance parts. For off-road use only. Installation should be carried out by a
qualified facility. Improper use or installation may result in injury or death.
VOODOO13
254 W Broadway Rd
Mesa, AZ 85210
Ph: 480.889.0812
Fax: [phone]
www.VOODOO13USA.com