Votek UT-6408 User manual

UT-6408 8
UT-6408
123
UT-6408 12/24/48VDC
1. V+ V-
2. DC
(10.8~52.8VDC)
1
23 1
V+V
1
2
UT-6408
10/100M 8
37mm
1.45in
150mm
5.90in
100mm
3.93in
37mm
1.45in
150mm
5.90in
37mm
1.45in
37mm
1.45in
150mm
5.90in
IEEE 802.3 10BaseT
IEEE 802.3u 100BaseT(X) 100Base FX
RJ45 8 10/100BaseT X
/ MDI/MDI-X
PWR , 1 8 RJ-45
12/24/48VDC(10.8~52.8VDC)
: 150mA@24Vmax
13
IP30
\
W x H x D 150mm 37mm 100mm
-10 60
-40 85
0 95% ( )
EMI FCC Part 15 Subpart B classA EN55022 class A
EMS
IEC(EN)61000-4-2(ESD)
IEC(EN)61000-4-3(RS)
IEC(EN)61000-4-4(EFT)
IEC(EN)61000-4-5(Surge)
IEC(EN)61000-4-6(CS)
IEC(EN)61000-4-8
IEC 60068-2-27(Shock)
IEC 60068-2-32(Freefall)
IEC 60068-2-6(Vibration)
a. PWR 1
PWR
b. RJ-45 100 Base
10 Base
12/24/48VDC(10.8~52.8VDC)

UT-6408 is a8-port industrial gradenon-managed Ethernet switch
with reverse polarity protection of DC input for avoidin g being damaged.
It has ingenious appearance design and supports industrial standard
snap-fit-mounting and wall-mounting installation, so it's very easy tobe
installed and used in any industrial networks.
a. PWR: power supply connected
as shown infigure 1 andthe red powerindication light PWRwill light,
the switch operatesnormally.
b. RJ-45 After network cableis connected theleft green light
will light for 100Base network and not light for 10Base network
The right yellowindication light isnetwork link indicationlight and
it will light when the network cable is connectedand switchoperates
normally. Bothyellow and greenlights will not light if the network
cable is notconnected.
12/24/48VDC(10.8~52.8VDC)
123
UT-6408series industrialgrade Ethernetswitch supports
power supply inputs,and the DC
model equips withreverse
polarity protection foravoiding being damaged.
1. Connect thepositive/negative polarity toV+ andV- terminals
respectively.
2. Tightenthe screws toavoid loose connectionand bad contact.
12/24/48VDC(10.8~52.8VDC)
Figure 1 Powersupply input terminal
23 1
V+V
1. DIN railmounting
Tighten the rail to machinewith accompanied screws.
Push the topside of UT-6408 rail seatinto the fixedrail.
Then push itinto the railslightly again
2. Wall mounting
Tighten themetal fixation stripwith accompanied screwsas
shown in theabove figure.
Then hang themachine with locked metal strip onto wall or
machine cabinet.
UT-6408
10/100M 8 Ports Industrial Grade
Unmanaged Ethernet switch Manual
37mm
1.45in
150mm
5.90in
100mm
3.93in
37mm
1.45in
150mm
5.90in
37mm
1.45in
37mm
1.45in
150mm
5.90in
.Main Features
Standard:
IEEE 802.3 10BaseT
IEEE 802.3u 100BaseT(X) and100Base FX
Interface:
RJ45 port:8 10/100BaseT(X) ports,
auto detection, self-adaptive full/half-duplex MDI/MDI-X
LED indicators:
PWR indicator and RJ-45 indicators for port 1-8
Power Supply:
Input Voltage 12/24/48VDC(10.8~52.8VDC)
Power consumption: 150mA@24Vmax
One pluggable 3-pin wiring terminal
Overload protection: Available
Polarity protection: Available
Mechanical Property:
Enclosure:IP30
Method of installation: Rail-mounted/wall-mounted
Dimension (W H D):150 mm 37mm 100mm
Working Environment:
Working temperature: -10 ~ 60
Storage temperature: -40 ~ 85
Relative humidity: 0% ~ 95% (no condensation)
Industry Standard:
EMI FCC Part 15 Subpart B classA EN55022 class A
EMS
IEC(EN)61000-4-2(ESD)
IEC(EN)61000-4-3(RS)
IEC(EN)61000-4-4(EFT)
IEC(EN)61000-4-5(Surge)
IEC(EN)61000-4-6(CS)
IEC(EN)61000-4-8
IEC 60068-2-27(Shock)
IEC 60068-2-32(Freefall)
IEC 60068-2-6(Vibration)