Voxmio Vox622 User manual
VOX622
Bluetooth stereo headset
User’s manual
Contents
Brief introduction…………...…………………………..…....1
Before use……………………………………………………..1
1. Overview…………………………………………………...……1
2. Charging for headset..……………………………………………2
Getting started……..…………………………………………3
1. Turning on/off the headset…………....……………………......3
2. Wearing the headset.......................................................................3
3. Pairing/connecting…….……..............................……………..….4
1) Pairing headset with Bluetooth cell phone via Bluetooth……..….4
2) Pairing headset with Bluetooth cell phone via NFC......................5
3) Pairing headset with multi devices via Bluetooth ….............…....6
4. Making a call with the headset………………………………...….6
5. Playing music………………………………………………..…...9
6. LED indicator………………………………………………....10
7. Factory Reset………………………………………………..….10
Care and maintenance……………………………..………..10
FAQs……………………………………...…………………..11
Specification……………………………...………………..…12
Welcome to use this Bluetooth stereo headset, VOX622. Please read this
user’s manual carefully before use.
Brief introduction
VOX622 is an In-ear Bluetooth stereo headset. Mini and portable design for
easy taking. You can use it to enjoy wireless music and make a call at the
same time. Besides, VOX622 support NFC technology for close pairing and
connecting.
Before use
1. Overview
1
1Cover of charging jack 6NFC area
2Micro USB charging jack 7LED indicator
3+ :volume up/previous song 8Microphone
4: Multi-functions button 9Big/middle/small eartips
5—: volume down/next song 10 Stabilizer
2. Charging for headset
The headset comes with a built-in rechargeable battery, prior to using it, it is
recommended to charge the battery fully for the first time.
When the headset is low power, the headset emits prompt tones every 5
minutes and the red LED flashes. Please recharge the battery of the headset.
The way of charging as following:
Using USB cable
1. Turn on the cover of charging jack, and plug the USB charging cable
2. Plug another side of cable tothe USB port of PC
Red light on: Charging
Red light off: Finish charging
3. It will takes about 2 hours to finish charging
Remarks:
1) The battery is recyclable.
2) Batteries (battery pack or batteries installed) shall not be exposed to
excessive heat place, such as sunshine, fire or the like.
2
Getting started
1. Turning on/off the headset
Functions Operation Prompt tone
Turning on Press and hold about 4
seconds until blue LED flashes
Four raise tone
Turning off Press and hold about 4
seconds until red LED flashes
Four fall tone
Remark: In order to save power, the headset will turn off automatically if
no devices can be connected after 5 minutes.
2. Wearing the headset
a. Put the stabilizer into the headset and rotate to the suitable position as
following shown:
3
b. Choose the suitable size eartips according to your ear and wear as
following shown:
c. Set up the cord management clips to get better wearing as following
shown:
3. Pairing/connecting
1) Pairing headset with Bluetooth cell phone via Bluetooth
Prior to using the headset for the first time, you have to pair it with a
Bluetooth-enabled cell phone. The pairing procedures are subject to
different models of cell phones. Please refer to your cell phone user’s
manual for further information.
The general pairing procedures are as follows:
1) Keep your headset turned off and within 1 meter of phone ;
2) Press and hold about 8 seconds until the red and blue LED flash
alternately, the headset enter into paring mode;
4
3) Activate your cell phone’s Bluetooth function and search for Bluetooth
devices within range, select “Voxmio Freebird Pro” from the list of
devices shown (enter password “0000 ” if the headset prompt);
4) After successful connecting, blue LED of headset flashes twice every 4
seconds
Remarks:
Pairing mode will last 2 minutes, the headset will back to standby mode
if the pairing failure.
If the pairing isnot successful, turn off the headset andrepeat the steps as
above.
Every time the headset is turned on, it will connect to last connected
device automatically. The headset can remember 8 paired devices, when
the number of paired devices exceeds 8, the first one will be replaced.
2) Pairing headset with a Bluetooth cell phone via NFC
VOX622 support NFC technology, it can quickly connect with Bluetooth
cell phone via NFC.
The general pairing procedures are as follows:
1) Please activate the Bluetooth and NFC function of cell phone;
2) Pairing and connecting with cell phone. Please refer to following
pictures:
5
Remarks:
Please keep the NFC area of cell phone and headset within 1 centimeter
until the red and blue LED of headset flash alternately(First pairing time
maybe 3 seconds).
The headset will disconnect when the NFC area of cell phone and headset
touch each other again.
3) Pairing headset with multi devices via Bluetooth
The headset can connect with two Bluetooth cell phones at the same time.
The general pairing procedures are as follows:
1) Pairing the headset with device one
2) Turn on the headset and make it enter pairing mode again, and pairing it
with device two
3) Operate device one to connectwith headset. The headset has already
connected with two devices in this moment
Remarks:
The multi-pair function is off in factory set, please turn on this function as
following:
Turn on: long press and + button under standby mode, and release it
until you hear four raise tone
Turn off: long press and—buttonunder standby mode, and release
it until you hear four fall tone
To improve the stabilization of headset, we suggest you turn off the
multi-pair function when you only connect with one cell phone.
4. Making a call with the headset
1) Basic operation
Functions Status of
headset
Operation Prompt tone
Cancel a call Calling Short press
once
One short
tone
Answer a call Incoming call
ringing
Short press
once
Two raise
tone
6
Reject a call Incoming call
ringing
Long press
about 2 seconds
and release it
until listen a
tone
Two falltone
End a call During a call Short press
once
One short
tone
Volume up During a call Short press +
button
Volume down During a call Short press —
button
Transfer
conversation
to mobile
phone
During a call Long press
about 2 seconds
One short
tone
Transfer
conversation
to headset
During a call Long press
about 2 seconds
One short
tone
Microphone
mute
During a call Long press “+”
about 2 seconds
Two falltone
Cancel mute During a call
(microphone
mute)
Long press “+”
about 2 seconds
Two raise
tone
Voice dial Standby mode
(connected
device)
Short press
and“+” button
simultaneously
One short
tone
Redial the
last number
Standby mode
(connected
device)
Double click
button
One short
tone
Warning: Excessive pressure from earphones and headphones can
cause hearing loss.
7
Note:
Not all the mobile phones support all the functions listed above. Different
function and prompt tone according to different mobile phone. Please
refer to your mobile phone user’s manual.
When the volume is adjusted to max or min, you will hear one prompt
tone.
When the headset under microphone mute mode, you will hear two tone
continuously every 10 seconds.
When pressing the answer button on some mobile phones, the call will be
transferred to the mobile phone. You can switch the call to the headset by
using the conversation switch button or through operating on the mobile
phone. Please refer to your mobile phone user manual for further
information.
2) Three-wayscalloperation
Functions Status of headsets Operation
Answer new call and
end current call
There are second
incoming call
Short press once
Answer new call and
retain current call
There are second
incoming call
Double click
button
Switch calls Keepconversation Double click
button
End current call and
switch retain call
Keep conversation Short press once
8
3) Connect with two cell phones
Functions Status of headset Operation
End phone call #1
and answer phone
call #2
During phone call #1,
phone 2 has incoming
call
Short press once
Retain phone call #1
and answer phone
call #2
During phone call #1,
phone 2 has incoming
call
Double click
button
Switch call During call, one of
phone call is retained
Double click
button
End current call,
back to retain phone
call
During call, one of
phone call is retained
Short press once
5. Playing music
Functions Status of the
headset
Operation
Volume up Playing music Short press “+”button
Volume
down
Playing music Short press “―”button
Last song Playing music Long press “+”button
Next song Playing music Long press “―”button
Pause Playing music Short press once
play Pausing Short press once
Notes:
When the volume is adjusted to max or min., you will hear one prompt
tone.
If you want to remote control last/next song, pause/play, it needs your
Bluetooth mobile phone or Bluetooth transmitter paired with the headset
to support AVRCP profile, please refer to the user’s manual of your
mobile phone or Bluetooth transmitter for further information.
9
6. LED indicator
LED indicator Status of headset
Red and blue LED flashes
alternately
Pairing mode
Blue LED flashes once every 2
seconds
Not connected to device
Blue LED flashes twice every 4
seconds
Connected to device
Red LED flashes instead of blue
LED
Low battery
7. Factory Reset
In the status of charging, long press “+” button about 4 seconds and release
it until the red and blue LED flashes simultaneously, you will hear 4 prompt
tone.
Remarks:
After factory reset, the paired list of headset will be deleted. After turn it on
again, the headset will enter pairing mode automatically, and you need to
re-pair and connect with Bluetooth devices.
Care and maintenance
Read the following recommendations carefully before using VOX622.
Following these you will be able toenjoy this product for many years.
Keep it dry and don’t put it in the dump place to avoid the product’s
internal circuit being affected.
Keep the product away from direct sunlight or hot places. High
temperatures will shorten the life of electronic devices, destroy the
battery or distort certain plastic parts.
Don’t expose the producttocold areas. It may damage the internal circuit
board.
Don’t try to disassemble the product as it may get damaged if you are not
professional.
Don’t let it fall down onto the floor or other hard surfaces. The internal
circuit might get damaged.
Don’t use intensive chemical products or detergent to clean the product.
10
Don’t scratch the surface with sharp things.
Don’t use this product during strenuous exercise. It may get damaged by
sweat.
In case the product doesn’t function properly, send it to the store you bought
it. The staff will help you to solve the problem
FAQs
1.What does it mean when red LED flashes instead of blue LED?
Battery is low power, need to be recharged.
2.Why is the red LED off when charging?
a) Please make sure the charging device connectwith headset Well;
b) The battery may dry up. Please charge the battery for 30 minutes, and
then the red LED will be ON.
3.Why my mobile phone can not search and find the headset?
Please make sure the headset is under the pairing mode and in the effective
working range, and then the headset can be paired and connected.
4. Why my mobile phone can not pair with headset via NFC?
a) Make sure activate NFC function of your mobile phone
b) Please keep the NFC chip of cell phone and headset within 1centimeter
until the red and blue LED of headset flash alternately (First pairing
time maybe 3 seconds).
5. Why can’t I hear the sound on the headset?
c) Make sure the headset has been switched on;
d) Make sure the volume is not too low or muted;
e) Make sure the headset connects with the mobile phone correctly;
f) Make sure the distance between the headset and the cell phone is in the
available Bluetooth range.
6. Why can’t I hear the sound clearly on the headset?
a) Make sure the mobile phone isinthe strong signal area;
b) Make sure the headset is in the available range of this product.
11
7. Why the pause/play, last/next song not function when playing music?
Make sure your Bluetooth device supports AVRCP (Audio/Video Remote
Control profile)
Specifications
Bluetooth version Bluetooth V4.0
Bluetooth profiles Headset, Hands free, A2DP, AVRCP
Operating distance 10meters
Headset music time About 5 hours
Headset talk time About 5.5 hours
Standby time About 200 hours
Headset charging time About 2 hours
Dimension Headset: 37x16.3x27.7 mm
Cable: about 500mm
Weight About 13 g
Notes:
1. This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
If you have any further questions don't hesitate to contact our customer
12
Table of contents
