VRI MedReady MDS User manual

V1.06302022
MedReady Medication Dispenser System
MeetYourNew MDS
MedReady was created to help manage your medication to
always take the right dose at the right time.
Get to Know Your Unit
Unit Facts & Features:
MedReady holds up to 28 doses Dispenses up to four times a day Locking lid prevents double doses
START
hour
min
am-pm
time set
alarm set
1 2 3 4
9
10
11
1
23
4
5
86
7
MedReady
OPEN
12:00
Medication Door
Allows client to removemedication and shuts off
audiblealarm
1
Lock and Key
Allows locking of the MedReady
2
Alarm Test & Time Set Buttons
Alarm test changes the amount of time the audible
alarm will go off for
Time set will enable the local time to be set on the
clock
3
Clock andIndicator Light
Displays thelocal timeand alarm times
4
Hour, Minute, AM/PM Buttons
Changes the Hour, Minute and AM/PM for local time
and alarm times. AM/PM will also test thedevice
5
Alarm Set Buttons (1,2,3,4)
Set alarm times (1 –4)
6
White T-Bar (Resets Alarm)
Resets alarm –Bar must bepushed up toward time
before placing lid on to work properly
7
Medication Tray
Medication placeholder
8
Power Jack
Connects unit to power outlet
9
BatteryJack
Connects battery pack to unit
10
Battery Pack
Back-up battery to unit
11
For additional questions, call tech support at 1-800-860-4230

V1.06302022
Welcome to your new medication dispenser system. If you
have any questions or in need of assistance, do not hesitate to call
us at 1-800-860-4230.
Quick Install
battery lid
bottom of
not operated by a light switch
battery pack
MedReady
OPEN
12:00
START
hour
min
am-pm
time set
alarm set
1 2 3 4
Turn off alarm by pressing and
holding button until light is off.
white bar
1. Flip MedReady upside down
2. Attach back up battery\replace
3. Attach supplied AC adapter to
MedReady
4. Plug into household power outlet. Make sure
that the outlet is
or power strip
5. For “MedReady Modem” plug supplied phone cord
into bottom of MedReady and wall jack
Connections
alarm
the
reset
1. Set clock to current time by holding the
“Time Set” button while pressing Hour,
Minute, and AM-PM buttons
2. To set alarm times; Press and Hold #1
(1st alarm of the day) then use the Hour,
Minute, and AM-PM buttons
Repeat step for alarms 2-4 as needed
3. When active there will be an “ON” light
above each active alarm time 1-4
4. Slide the white bar to the center near
“X” until it locks in place
5. Press alarm test, after alarm goes off,
white bar back to the “X” location
(This will silence alarm)
Setting Times/Alarms
alarm
1. Fill the medication wheel one dose per
compartment
2. Load in a counter clockwise direction
3. 4 doses a day will hold 7 days of meds
4. Slide the white bar back to the center
near the “X”
5. Close the lid, lock it, and verify the
lights are “ON” for any dispenses you have
programmed
Loading the Dispenser
:
Twist lid counter clockwise to remove
MedReady will automatically set the correct
time after 20 minutes
MedReady Connect should be pre-paired to your
PERS device
Always observe AM-PM on the clock & alarm times
MedReady display will flash “ ” when running on
back up battery
MedReady Install Tips
For additional questions, call tech support at 1-800-860-4230
MedReady Medication Dispenser System