WA Library Supplies 2609 User manual

2609
Spinner with
lockable castors
Assembly Instrucons
Parts Supplied for Spinner Plate:
Step 1: Line up Spinner Plate (C) with holes on
Spinner mounng panel (B). Screw 4 x 6mm bolts
(D) into the 4 nutserts on mounng panel.
B
C
Step 2: Push 4 x 40mm bolts (E) (from underneath)
through cut outs in spinner plate. Save nuts for a later
step.
B
1 x Spinner
Plate - Top-
Board
500mm x 500mm
1 x Spinner
Plate Mounng
Panel
390mm diam.
1 x Metal
Spinner Plate
195mm x 195mm
4 x 6mm bolt
4 x 40mm bolt 4 x 10mm nuts
A B C D E F
PART 1 - BUILD SPINNER PLATE
8 x Cam Pins
8 x Cam locks
(pre-inserted - not
loose)
G
Step 3: Screw in 8 x cam pins (G) into cam pins
holes on Spinner Base panel (A).
B
A
Step 4: On opposite side of Spinner Base panel (A) line up
spinner plate with holes and push through bolts.
Lock bolts in with 4 nuts (F).

2609
Spinner with
lockable castors
Assembly Instrucons
Parts Supplied for Spinner Base:
Step 5: Screw in 8 x cam pins (G) into cam pins
holes on Spinner Base Board(H).
GG
I
1 x Spinner
Base Board
490mm x 490mm
2 x Metal Rails
410mm x 30mm
2 x Side Panel
Short Side
450mm x 285mm
2 x Side Panel
Long Side
485mm x 285mm
2 x swivel castors
&
2 x locking
castors
4 x 40mm bolt
H I J K L E
PART 2 - BUILD BASE
12 x Cam Pins
12 x Cam locks
(pre-inserted - not
loose)
G
Step 7: Screw in 2 x cam pins into both Long Side
Panels (K). Then push Side Panels (K) & (J) togheth-
er. Lock cam locks by turning unl ght.
J
K
Step 8: push in Base Panel and Spinner Base Panel into
Side Panels. Lock cam locks by turning unl ght.
4 x 10mm nuts
F
Step 6: on opposite side of Base Board (H) line up met-
al rails (I) with holes. Push through 4 x 40mm bolts (E)
through board and rail from underneath, lock with 10mm
nuts (F). Screw in castors (L).
J
K
L
Read through instrucons rst prior to starng assembly
Cam pins can be pre-screwed into panels to save me during assembly.

2609
Spinner with
lockable castors
Assembly Instrucons
Parts Supplied for Upper Secon:
Step 9: Remove
backing paper from all
acrlyic panels.
HINT:
Using a dowel, rod
or cardboard tube,
posion the rod at the
corner of the sheet,
wrapping it around
the rod and slowley
roll o the paper
backing. I
2 x Internal
Acrlyic Panel -
Small
1005mm x 90mm
1 x Internal
Acrlyic Panel -
Large
1005mm x 180mm
4 x External
Acrlyic Panel
1035mm x 130mm
3 x Centre
Divider Panel
260mm x 260mm
2 x Top & Base
Panel
260mm x 260mm
4 x 28mm bolt
MN O P Q R
PART 3 - BUILD UPPER SECTION
40 x 9mm bolt
S
Step 10: Line up
1 x Boom Panel (Q)
and 3 x Centre Divider
Panels (P)
and then screw in 2
ONLY of the External
Acrylic Divider Panels
(O)
using
16 x 9mm bolts (S).
DO NOT OVERTIGHTEN
BOLTS AS ACRYLIC MAY
CRACK
Step 11: Slide down
the
1 x Large Internal
Acrylic Panels (N) and
2 x Small Internal
Acrylic Panels (M)
through centre cut
outs.
Step 12: Screw in
the other 2 x
External Acrylic
Panels (O).
Use bolt (S).
TO WORK OUT TOP OF
UNIT:
Make sure the acrylic
is on the le hand side
with the opening on the
right hand side.
If it is put on upside
down, books will not
display correctly.
Step 13: Aach the remaining
Top/Base Panel (Q) and secure
into place with bolt (S).
Step 14: Aach the top of the
spinner to the Spinner plate.
Use 4 x bolts (R), line up holes
and screw into place.
N
MM
O O
P
P
P
Q
Q
R