WAGO 758-919 User manual

Manual
758-919
Wireless Access Point
Version 1.0.0

2
758-919 Wireless Access Point
Manual
Version 1.0.0
© 2020 WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]
Web: www.wago.com
Technical Support
Phone: [phone] – 4 45 55
Fax: [phone] – 84 45 55
E-Mail: [email protected]
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [email protected]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.

Table of Contents 3
758-919 Wireless Access Point
Manual
Version 1.0.0
Table of Contents
1Notes about this Documentation .............................................................5
1.1 Copyright................................................................................................5
1.2 Symbols .................................................................................................6
1.3 Number Notation ....................................................................................8
1.4 Font Conventions ...................................................................................8
2Important Notes ........................................................................................9
2.1 Legal Bases............................................................................................9
2.1.1 Subject to Changes............................................................................9
2.1.2 Personnel Qualification ......................................................................9
2.1.3 Intended Use .....................................................................................9
2.1.4 Technical Condition of Specified Devices...........................................9
2.2 Special Use Conditions for ETHERNET Devices ..................................11
2.3 Storage, Assembly and Transport ........................................................12
2.4 Safety Advice (Precautions) .................................................................13
3Device Description..................................................................................16
3.1 General Description..............................................................................16
3.2 View .....................................................................................................18
3.3 Labeling................................................................................................19
3.4 Connectors ...........................................................................................20
3.5 RJ45 LED Indicators ............................................................................21
3.6 RESET Button ......................................................................................22
3.7 Technical Data .....................................................................................23
3.7.1 Hardware Specifications ..................................................................23
3.7.2 Communication................................................................................23
3.8 Approvals .............................................................................................25
3.8.1 Radio Regulatory Compliance..........................................................26
3.9 Selecting the Installation Location ........................................................27
4Installation...............................................................................................29
4.1 General Information..............................................................................29
4.2 Limitations ............................................................................................29
4.3 Mechanical Installation .........................................................................30
5Configuration ..........................................................................................31
5.1 General ................................................................................................31
5.2 Web Interface .......................................................................................32
5.2.1 System Overview .............................................................................32
5.2.2 Easy Config .....................................................................................33
5.2.3 Network Settings..............................................................................35
5.2.4 WLAN Settings – Client ...................................................................36
5.2.5 WLAN Settings – Access Point ........................................................39
5.2.6 Bluetooth Settings – General ...........................................................41
5.2.7 Bluetooth Settings – PANU Mode....................................................42
5.2.8 Bluetooth Settings – NAP Mode.......................................................43
5.2.9 Bluetooth LE Settings ......................................................................44
5.2.10 Firmware Update .............................................................................45

4 Table of Contents
758-919 Wireless Access Point
Manual
Version 1.0.0
5.2.11 Configurations via AT Commands....................................................46
5.2.12 System Settings...............................................................................47
5.3 Factory Restore....................................................................................48
6Appendix .................................................................................................49
6.1 Configuration Examples........................................................................49
6.1.1 Ethernet Bridge via WLAN or Bluetooth® (Easy Config) ..................49
6.1.2 PROFINET networking via Bluetooth®..............................................50
6.1.3 EtherNet/IP™ Networking via Bluetooth®........................................51
6.1.4 Ethernet network to existing WLAN .................................................52
6.1.5 Adding single Ethernet node to WLAN.............................................53
6.1.6 Accessing PLC via WLAN from Handheld Device............................54
6.2 Wireless Technology Basics.................................................................56
6.3 Radio Antenna Patterns .......................................................................57
6.3.1 Azimuth (Horizontal) View................................................................57
6.3.1.1 Front View – Vertical 0° ...............................................................59
6.3.1.2 Side View – Vertical 90° ..............................................................60
6.3.2 Vertical Views ..................................................................................60
6.3.3 Throughput Diagram ........................................................................61
6.4 Data Security for Radio Transmission...................................................61
List of Figures ..................................................................................................62
List of Tables....................................................................................................63

Notes about this Documentation 5
758-919 Wireless Access Point
Manual
Version 1.0.0
1 Notes about this Documentation
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation
is included, if necessary.
This documentation applies to the Wireless Access Point 758-919
1.1 Copyright
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.

6 Notes about this Documentation
758-919 Wireless Access Point
Manual
Version 1.0.0
1.2 Symbols
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.

Notes about this Documentation 7
758-919 Wireless Access Point
Manual
Version 1.0.0
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).

8 Notes about this Documentation
758-919 Wireless Access Point
Manual
Version 1.0.0
1.3 Number Notation
Table 1: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated
with dots (.)
1.4 Font Conventions
Table 2: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.: Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under
Start of measurement range
.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.: [F5]

Important Notes 9
758-919 Wireless Access Point
Manual
Version 1.0.0
2 Important Notes
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
2.1 Legal Bases
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all
rights arising from the granting of patents or from the legal protection of utility
patents. Third-party products are always mentioned without any reference to
patent rights. Thus, the existence of such rights cannot be excluded.
2.1.2 Personnel Qualification
All sequences implemented on the device may only be carried out by electrical
specialists with sufficient knowledge in installation and handling of electrical
equipment. The electrical specialists must also be familiar with the current
standards and guidelines valid for the device.
2.1.3 Intended Use
The intended use of this equipment is as a communication interface and
gateway. The equipment receives and transmits data on various physical levels
and connection types.
If this equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment may be impaired.
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. These
modules contain no parts that can be serviced or repaired by the user. The
following actions will result in the exclusion of liability on the part of WAGO
Kontakttechnik GmbH & Co. KG:
• Repairs,
• Changes to the hardware or software that are not described in the
operating instructions,
• Improper use of the components.

10 Important Notes
758-919 Wireless Access Point
Manual
Version 1.0.0
Further details are given in the contractual agreements. Please send your
request for modified and new hardware or software configurations directly to
WAGO Kontakttechnik GmbH & Co. KG.