Wahl MC3 User manual

WAHL
HOME PRODUCTS
®
Section 4:
Top of the head
Section 1:
The neckline
Section 2:
Under the rim
of the head
Section 3:
The rim or side
Quick Start Guide
Use for blending
between different hair
lengths. The taper lever
adds versatility to your
clipper by allowing you
to gradually change the
closeness of your cut.
(Up position = closest cut;
Down position = longest
cut)
(A) Oil blades as noted
on this sheet.
(B) You can reduce the
“clatter sound” by
adjusting the power
screw. The power
screw was adjusted for
Blend it!
Too Noisy?
Helpful Hints
Use brush included to clean out excess hair
on clipper and between blades (don’t clean
with running water)
SAFETY FIRST! Please read instruction book
first before using clipper
If defective contact Wahl via 1-800-767-9245
peak efficiency before leaving the factory.
However, if voltage in your home is too high or
low; the clipper power screw may need
adjustment.
Adjust Power Screw to Reduce Clipper Noise
(excessive clattering)
1. Turn your clipper “ON”
2. Use the end of the cleaning brush or a
Haircutting Tips & Techniques
When you cut your hair, you should visualize the
head as if it were divided into four sections.
Image to the left shows the different sections.
Using proper techniques when moving from one
section to the next will help you blend the sections
together for professional looking results. See
instruction book for more tips.
For best results...
- The first time you cut your hair, cut only a small
section using the largest attachment guard size
until you become better accustomed to the
clipper and guard sizes.
- Hair should be dry before using clipper
- Don't force the clipper through the hair, go
through at a slow, even speed.
- Go through the hair against the direction of your
hair's growth.
©2020
part no: 92365-2901
v. 04.2020
Keep it Running Like New!
You can do it!
closest
cut
longest
cut
Adding Attachment Guards
Removing
Attachment Guards
Goof- Proof!
From underneath
metal attachment
clip, lift up to
release from blade.
Align guard onto blade then press down on
the name plate until you hear a snap.
For best results, place
three drops on front of
the blades and one drop
on each side of blade as
shown. Use only the Wahl
Clipper Oil included in the pack. Do not use
hair oil, grease or any oil mixed with kerosene
or any solvent.
To remove hair between the blades, use
cleaning brush as provided. DO NOT USE
WATER TO CLEAN THE BLADES. For best
results, after brush cleaning the blades, add
Wahl clipper oil to the blades.
The blades of your new
clipper should be oiled
every few haircuts.
screwdriver to turn power screw in a COUNTER
CLOCKWISE direction until clatter goes away.
Max Power!
Adjusting Power Screw for Maximum Power
Setting
1. Turn your clipper “ON”
2. Use the end of the cleaning brush or a
screwdriver to turn power screw in a CLOCK-
WISE direction until you hear a clattering noise.
3. Then turn power screw in opposite direction
(COUNTER CLOCKWISE) until clattering stops.

Home Haircutting
Easy step-by-step instructions
included. For more haircutting
tips and techniques visit
wahlUSA.com.
- Make sure trimmer is turned off "0" position.
- Plug-in cord to trimmer and into outlet with correct voltage.
- Trimmer charge light will illuminate to indicate trimmer is charging. Note: The light will
remain on until unplugged (no indicator when unit is fully charged).
- The trimmer should be plugged-in for at least 10 hours for a full charge. Please charge
before using for the first time.
- The transformer charger is designed to continuously charge without overcharging.
- You may use with or without cord. If trimmer charge is low, you can plug-in and still use.
- For longest battery life, don't recharge after each use
Thank You!
Thank you for purchasing this
Wahl haircutting kit.
We appreciate your support and
we hope you enjoy your new
clipper!
If you have any questions, please
contact one of our USA based
customer service representatives
located next to our factory in
Sterling, IL USA.
1.800.767.9245
(M-F 7:30am - 4:30pm CST)
[e-mail]
wahlUSA.com
Find us on social media:
@WAHLGROOMING
Quick Start Guide
Of domestic and imported parts
Quality products made in the USA
YOUR NEW CLIPPER!
DETAIL TRIMMER - CHARGING SELECT CLIPPER KITS INCLUDE A RECHARGEABLE TRIMMER,
YOUR KIT MAY NOT INCLUDE A TRIMMER
Taper
Lever
Power
Screw
Cord
On/Off
Switch
Models MC3 Model MC2
SC2
Model 5612
Please reference instruction books for full details
Taper
Lever
Blades
Blades
Power
Screw
Cord
On/Off
Switch
(SC2 model doesn't
include a taper lever)