Wali MATI001-G User manual

INSTALLATION MANUAL
[email protected]
75x75/100x100 32"
MAX 2~9.9kg
( 4.4~22lbs)
RATED
MATI001-G
MATI001-W
Single Monitor Desk Mount

2

Supplied Parts List
3
Arm
A (x1)
Bolt
I (x1)
M6x12 Bolt
J (x3)
Arm
B (x1)
VESA Plate
C (x1)
Spring Washer
K (x1)
Anti-skid Pad
M (x2)
M5x12 Bolt
M-B (x4)
Nut
L (x1)
Base
F (x1)
Bottom Grommet Plate
H (x1)
Plate
G (x1)
Allen Key 4mm
N (x1)
Fit clamp: 0.4”-3.3”
Grommet: 0.4”-3.1“
Allen Key 5mm
O (x1)
Wrench
P (x1)
C-Clamp
D (x1)
C-Clamp Brace
E (x1)
M4x12 Bolt
M-A (x4)
D5 Washer
M-C (x4)
Step 1

4
Step 2
Option A
Clamp Installation
N
N
N
N
D
D
J
E
E
F
M
2. Loosen the Bolts on the C-Clamp Brace Eusing Allen Key 4mm Nto the preferred height according to your desk thickness.
Hang the C-Clamp Don the bolts and tighten using Allen Key 4mm N.
1
Leave 6mm gap
0.4’’-2.2’’
1
2
1.4’’-3.3’’
2
3
or
1. Connect the C-Clamp Brace Eto the Base Fusing 3 pcs M6X12 Bolt Jand tighten with Allen Key 4mm N. Tear off the
protective paper to attach Anti-Skid Pad Mto the bottom designated position of Base as the image shown.

Step 2
5
Option B
Grommet Base Installation
3. Rotate the knob clockwise to fasten for stability.
1. Attach the Plate Gto the Base Ffrom the bottom using 3 pcs M6X12 Bolt Jand tighten with Allen Key 4mm N.
Tear off the protective paper to attach Anti-Skid Pad Mto the bottom designated position of Base as the image shown.
N
D
J
G
M
F

2a. Existing Grommet Hole Installation
If the existing grommet hole comes with a plastic
protector, remove it to ensure a flat surface before
installing the desk mount.
Mark the position of the hole on your mounting surface.
Drill a 3/8"(10mm) diameter hole at the marked position
through the mounting surface.
2b. Self-drilled Grommet Hole Installation
I
F
H
K
L
P
0.4’’-3.1’’
0.4’’-3.1’’
Φ0.4’’-2.4’’
ø 10mm
(ø ")3/8
3. Insert Bolt Ithrough the Base Fand mounting surface. Guide Bottom Grommet Plate H, Spring Washer K,
and Nut Lthrough Bolt Ifrom the bottom . Fasten the Nut Lusing the provided Wrench P.
6

B
F
B
A
7
Step 3
Connect the Arm B to the Base Fand tighten with Allen Key 4mm N.
Connect the Arm Ato the Arm Band tighten with Allen Key 4mm N.
N
N

A
C
Hand thread screws
into the threaded
inserts on the back
of your TV to
determine which
screw diameter
(M4) or (M5) to use.
M5x12M4x12
C
8
Step 4
Step 5
Turn the knob on the VESA Plate Cto the unlock position, slide the assembled TV/Monitor onto the Arm A
and ensure the stability. Turn the knob to the lock position.
Select M4x12 Bolt M-A or M5x12 Bolt M-B according to your TV/Monitor, connect VESA Plate Ctogether with D5
Washer M-C into the mounting holes on the back of TV/Monitor, tighten with screwdriver. (Screwdriver needed but not
included) UnlockLockM-A
M-B
M-C
Step 4.1
Step 4.2

O
9
Step 6
To properly balance the arm with monitors mounted, adjust the spring tension with Allen Key 5mm O.
For heavier monitors, turn the adjustment screw
clockwise until it stays in a horizontal position.
First, position and firmly hold the arm horizontally
as shown. Ask for assistance should you require it.
CAUTION: To avoid damage to monitors or
mount, always keep the arm in a horizontal
position while making adjustments.
Again, ask for assistance if required.
For Lighter Monitors, turn the adjustment
screw counter-clockwise until it stays
in a horizontal position.
CAUTION:
· Do not over tighten the screws.
· To prevent damage to the Tension Indicator,
never allow the Red Indicator Line move
beyond the "-" and "+" found on the Left and
Right Side of the tension indicator.

N
N
10
Step 7
Step 8
±180°
±90°
Tighten the limiting screw
(do not overtighten). Arm can rotate 180°.
Remove or loosen the limiting screw. Arm can rotate without stopping.
Pull the bottom cable slot cover to detach it off the arm. Guide the cable through the cable slot and slide the cover back to arm.
Screw Adjustable to prevent monitor arm from swinging into screens or walls.