Wali TVDVD-5 User manual
INSTALLATION MANUAL
TVDVD-5
Table Top TV Stand
40kg
88lbs
RATED
30”-70”
MAX
Min: 150x100mm
Max: 600x400mm
2
Supplied Parts List
3
Base
①
(×1)
Support Pillar
②
(×1)
Bolt M6×30mm
A (×3)
Foot Pad
I (×4)
Washer
B (×1)
Safety Lock
G (×2)
Wire Clip
H (×2)
M8×45mm
M-D (×4)
M8×15mm
M-C (×4)
M8×65mm
M-E (×4)
M6×30mm
M-B (×4)
M6×15mm
M-A (×4)
M6 Nut
C (×4)
D6 Washer
D2 (×4)
Bolt M6×50mm
D1 (×4)
D5mm/D8mm
M-F (×4)
H10mm
M-H (×8)
H5mm
M-G (×8)
Plastic Cover
F (×1)
Bolt M6×10mm
E (×4)
Allen Key 4mm
J1 (×1)
Wrench
J2 (×1)
Connecting Plate
⑥
(×1)
Angle Adjuster
⑦
(×1)
TV Plate
⑤
(×2)
Support Pillar
③
(×1)
TV Bracket
④
(×2)
NOTE : SOME HARDWARE INCLUDED MAY NOT BE USED
4
Step 1
Step 2
③
②
E
②
③
J1
Connect two Support Pillar ②& ③ . Then insert 4pcs Screws E through the holes of Support
Pillar ②& ③ , and tighten using Allen Key 4mm J1.
E
②③
②③
J1
Note:
Support Pillar should be assembled
with clip holes in the same side.
①
I
Tear off the protective paper to attach Foot Pads I near the bottom four corners of the
Base ①as image shown.
①
I
5
Step 3
Step 4
A
B
①
F
③
J1
Put Base ① on the table; put Washer B and M6×30mm Bolts A on the base; put Plastic
Cover F and Support Pillar ③under the base. Then tighten the bolts A using Allen Key
4mm J1 .
A
A
B
①
F
③
J1
Table
Note:
Support Pillar should be placed
with clip holes facing backwards.
1. Connect TV Plate ⑤ and Angle Adjuster ⑦ by using Connecting Plate ⑥and M6 Nuts C .
Tighten the nuts using the Wrench J2 .
C
C
⑦
⑦
⑥
⑥
⑤
⑤
⑤
J2
J2
2. Connect TV Plate Unit to Support Pillar ②at your desired position (three options) using Bolts D1
and Washers D2 . Tighten them using Allen Key 4mm J1 .
6
Step 4
②
②
J1
J1
D1
D1
D2
D2
55mm
55mm
55mm
Note:
Three choices for
height adjustment.
Note:
TV Plate should be
installed with the ARROW
mark pointing UPWARDS.
Step 5
7
Attach the TV Brackets ④ to the back of TV using TV screws, washers and spacers.
TOP OF TV
M-F
M-G M-H
M-C
M-A M-B
M-E
M-D
④
④
Hand thread screws
into the threaded
inserts on the back of
your TV to determine
which screw diameter
(M6 or M8) to use.
Step 5.1 Step 5.2
Select Spacers ( if needed )
Select TV Screws
Step 5.3 Attach the TV Brackets
Only one screw size fits your TV
M8M6
8
Step 6
Choose the appropriate position (three options) for your TV. Hang your TV with
brackets onto the TV plate. Put the Safety Lock G in place and tighten the fixing
screw to the TV plate securely.
Hang on top
of TV plate
To the bottom
Lock to the bottom
of the TV Plate
G
G
Note:
Three choices for
height adjustment.
45mm
45mm
9
Step 7
Attach Wire Clips H into the holes of Support Pillar ② & ③ .
Guide the cable through the Wire Clips H .
H
H
H
③
③
②
②
10
Swivel Adjustment
Adjustments
(If necessary)
-20° +20°
Refer to the below illustrations to adjust swivel angle.
Wall
Note: When the TV Stand is
placed against the wall, the actual
swivel angle is determined by the
screen size.
Loosen 4 tilting bolts by MAXIMUM 1 turn using
Wrench J2 .
Hold the TV with your hands, then adjust TV
to your desired angle.
Tighten 4 tilting bolts using Wrench J2 .
J2
J2
J2
Tilting
Nuts
Tighten
Loosen
Loosen
Tighten
0°
+5°
Clockwise, Tighten
Counterclockwise, Loosen
Tilt Adjustment
+
-
11
Product Dimensions
110mm
/4.33"
MAX:
400mm/16"
MIN:
100mm/4"
MAX:600mm/24"
MIN:150mm/6"
16mm
/0.63"
MAX:
781mm
/30.75"
MIN:
581mm
/22.87"
+20°/-20°
633mm/24.92"
571mm
/22.48"
280mm
/11.02"
420mm/16.54"
40mm
/1.57" 70mm
/2.76"
130mm
/5.12"
+5°
0°
45mm/1.77"
45mm/1.77"
139mm
/5.47"
434mm
/17.09"
If you have any questions,please contact us.
We support the technology that brings your home to life.
We offer high quality products, professional customer service,
and extensive technical support.
www.walielectric.com
Table of contents
Other Wali Rack & Stand manuals
