Wali MF003 User manual

MF003
WARNING
！
！
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
Triple Monitor Desk Mount
75x75\100x100
INSTALLATION MANUAL
1-844-SATTLER (18447288537)
[email protected]
www.walielectric.com
(10kg/22lbs)x3
RATED
MAX 27”
TIPOVER WARNING
● NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
● USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
Supplied Parts List
VESA Plate
d (x3)
Nut
h (x3)
M5x14 Bolt
e (x3)
Support Plate
j (x1)
Spring Washer
l (x1)
M10 Washer
k (x1)
M10 Bolt
i (x1)
Grommet Base Plate
m (x1)
Wire Clip
n1 (x2)
Wire Clip
n2 (x4) M4 Spacer
s (x12)
M4x30 Bolt
r (x12)
Wrench
p (x1)
M4x12 Bolt
q (x12)
Monitor Arm
c2 (x1)
Lower Pole
a (x1)
Allen Key
o (x1)
Weighted Base
b (x1)
e
a1
o
Install the Pole a to the weighted Base b using 3pcs M5x14 Bolts e , and tighten with the Allen key 3mm o .
1
This step is depending on your personal preference
To provide stability for a heavier monitor, we may recommend install the mount to the hole in your desk.
i
k
j
p
l
a1 b
b
o
e
0.4‘’-3’’
b: Self-drilled Hole Installation
Option A: Free Standing Installation (Using V-vase)
a: Existing Grommet Hole Installation
i
k
j
p
l
ø 10m
0.4‘’-3”
m
(ø ")3/8
OR
√
Swivel Arm
c1 (x1)

4
c1
s
o
a1
m
e
0.4‘’-3’’
a: Existing Grommet Hole Installation
Place Pole a onto Grommet Base Plate m .
Connect them from the bottom using M5x14
Bolt e and tighten with Allen Key 3mm .
oe
a1 m
j
a1
j
k
l
p
i
b:Self-drilled Grommet Hole Installation
ø 10mm
(ø ")3/8
Option B: Grommet Base Installation (For saving more space)
0.4‘’-3’’
j
j
k
l
i
a1
OR
Notice: Please make sure the security nut is installed before you rotate the monitor.
5If one monitor is lower, remove the Nut h and turn the bolt counter-clockwise using
Allen key 3mm o to raise the monitor. Tighten the VESA Plate e with Nut h for stability
after the adjustment.
4Put the assembled TV/Monitor onto the Arms & and tighten the VESA Plate e with
Nut h for stability.
Select bolts and spacers (if needed) according to your TV/Monitor. Attach the VESA Plate to the Monitor and tighten with a screwdriver. (Screwdriver not included)
7For safety, please do not extend the arms too far forward or backward. This may cause
instability and tip over.
6Guide the cable through the Wire Clips ( n1, n2 ) and store the Allen Keys o in the Wire Clip n1 .
Adjust the tilt angle using Allen Key 5mm n .
n1 n1 on2
Step 3.1
Select Monitor Screws
90°
90°
90°
90°
15°
15°
Step 3.3a
Flat Back Monitor
Step 3.3b
Curved or Recessed Back Monitor
h
h
d
o
o
h
d
c1
d
d
r
s
q
c1 c2 d
d
c2
M4x12 M4x30
Ignore this step if monitors are level.
n2
o
d
h
3
Only one screw size fits your Monitor
Step 3.2
Select Spacers ( if needed )
Hand thread screws into the
threaded inserts on the back
of your Monitor to determine
which screw (M4x12 or M4x30)
to use.
h
h
d
o
n1 o
h
Note: Please make sure two arms are aligned and balanced.
2Put the Wire Clip n1 and Arms & through the Poles , adjust the preferred height
and tighten using Allen Key 6mm o . Attach the Wire Clips n1 to the Swivel Arm d .
c1
c1 c2
n2
n1 a
o
o
c2
n2
n1
c1