Wali TVF001XL User manual

WARNING
！
！
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
100x100\100x200\200x100
200x200\300x200\300x300
400x200\400x300\400x400
1-844-SATTLER (18447288537)
[email protected]
www.walielectric.com
40kg/88lbs
RATED
MAX 55”
TIPOVER WARNING
INSTALLATION MANUAL
TABLETOP TV STAND
TVF001XL
Supplied Parts List
Base
A (x1)
Washer
M (x3)
Nut
L (x4)
Step Washer
N (x3)
Wrench
O (x1)
M5x14 Bolt
M-A (x4)
M6x14 Bolt
M-B (x4)
M6x30 Bolt
M-C (x4)
M8x30 Bolt
M-D (x4)
M8x50 Bolt
M-E (x4)
D5 Washer
M-F (x4)
D8 Washer
M-G (x4)
Spacer
M-H (x8)
Spacer
M-I (x8)
Pole
B (x1)
VESA Plate
C (x1)
Adapter
D (x4)
Pole Cover
F (x1)
Plate
E (x1)
Wire Clip
G (x2)
Anti-Skid Pad
H (x4)
M6x25 Bolt
J (x3)
M6x12 Bolt
I (x4)
M6x50 Bolt
K (x1)
Tear off the protective paper to attach Anti-Skid Pad to the bottom designated position of Base as image shown.
1Connect Pole , Plate and Base from the bottom using M6x25 Bolt , Washer and Step Washer , tighten with a screwdriver.
(Screwdriver not included)
2
A
B
E
N
MJ
H
A
HB E A
A
N
M
J

M-A
M-H
M-I
M-H
M-I
M-G
M-E
I
C
M-A
M-F
M-B
M-G M-G
M-H
M-I
M-H
M-I
M-G
M-E
C
D
OR
G
F
OR OR
Too S hort
Too l ong
Hand thread screws
into the threaded
inserts on the back of
your TV to determine
which screw diameter
(M5, M6 or M8) to use.
M5 M6 M8
Only one screw size fits your TV
Select bolts and spacers (if needed) according to your TV/Monitor. Attach the VESA Plate to the TV and tighten with a screwdriver. (Screwdriver not included)
3
Press Pole Cover into the top of Pole . Select the preferred height and attach the VESA plate to the hole on the Pole .
Tighten the VESA plate using the M6X50 bolt with a screwdriver. (Screwdriver not included)
4Fix the Wire Clip onto the back of Pole and guide the cable through the Wire Clips . 5
Manually adjust swivel angle. (Swivel -35°/+35°)
6
± 35°
F
G
G
G B
F
C
C
B
B B
K
K
B
C
M-A M-B
M-I M-I
M-H
M-H
M-I M-I
M-H
M-H
M-D
M-F
M-A
M-F
M-C
M-G
M-D
M-C
M-G
M-G
M-B
M-G
M-G
M-E
M-G
M-E
D
C
I
O
L
Step 3.1 Step 3.2 Step 3.3
15.5”
13.6”
11.6”
VESA:300x300/400x400 VESA:300x200/400x200VESA:400x300