Walmart WMBR-1 User manual

WiFi Bridge WMBR-1 User Manual
WARNING
• Read, keep and follow these instructions. !
• Heed all warnings. !
• Disconnect from power source before cleaning.!
• Clean only with a dry cloth.!
• Do not install near any heat sources as radiator, heat registers, stoves and other apparatus (including
amplifiers) that produce heat. Yeah !
Always use the product WiFi Bridge (sometimes referred to as the “product”, “device” or “equipment”) in a
manner consistent with the InHome Terms of Use.
Test Internet connection after power has been disconnected or interrupted.!
Disconnect the power adapter or any other connected peripherals if any of the following conditions exist:
• The power cable or connector is damaged or frayed. !
• You want to clean the WiFi Bridge.!
• The WiFi Bridge or attached cables are exposed to rain, water/fluids, or excessive moisture. !
• The WiFi Bridge or its power adapter is damaged or has been dropped and you suspect it needs to
be serviced. !
IMPORTANT CONSUMER INFORMATION: Please read before activating or using the device.
WARNING: This product contains chemicals known to the State of California to cause cancer and
reproductive toxicity. For more information please call 1-833-235-2111.

FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Important Note: FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your
body.
Information for the user
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna. !
• Increase the separation between the equipment and receiver. !
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected. !
!
!
!
!

BASIC OPERATION
Your WiFi Bridge should be professionally installed by one of Walmart InHome’s preferred installers. If
something is wrong with your WiFi Bridge or other Walmart-supplied devices for your InHome system,
please contact customer support at 1-833-235-2111.
The WiFi Bridge should be placed within a central location where wireless internet signal is available. The WiFi
Bridge should also be placed within proper distance of the Garage Door Controller that will be used for the
InHome service. Please use the provided power supply as use of an unauthorized power supply may damage
the unit and void your warranty.
Once the WiFi Bridge has been set up and is operational, the WiFi Bridge's LED front indicator should be lit
solid white during normal operation. If the WiFi Bridge is not setup correctly and the LED is blinking, please
contact customer support.
To update or change the wireless network your WiFi Bridge is connected to, go to the “Settings” page of the
InHome app by tapping the gear icon at the top right corner of the home screen. This will take you to a page
where you can change the network your Wifi Bridge connects to.
Z-WAVE FUNCTIONALITY AND ADVANCED FEATURES
The WiFi Bridge is a Z-Wave certified central static controller. It is a security enabled Z-Wave product.
The WiFi Bridge ignores Basic Command Class Set commands.
This WiFi Bridge can be operated in any Z-Wave network with other Z-Wave certified devices from other
manufacturers. All mains operated nodes within the network will act as repeaters regardless of vendor to
increase reliability of the network.
This WiFi Bridge has one Association Group, commonly referred to as ‘Lifeline’.
If the access device is not included using S2 or included correctly using S2, it will default to S0 security.
EXCLUSION
1. From the home screen, navigate to the Settings page by pressing the (insert gear icon)
2. Select the About page
3. Select ‘Advanced Z-Wave Utilities’
4. Select ‘Exclude garage opener’ to put the bridge in Exclusion Mode. Refer to the manufacturer’s
instruction for exclusion.
5. The app will indicate when device exclusion is successful.
INCLUSION
1. From the home screen, navigate to the Settings page by pressing the (insert gear icon)

2. Select the About page
3. Select ‘Advanced Z-Wave Utilities’
4. Select ‘Add device’
5. Refer to the manufacturer’s instruction for inclusion using the DSK (device specific key). A user may
attempt to use classic inclusion by entering `00000` as the DSK.
6. The app will indicate when device inclusion is successful
LEARN MODE
1. From the home screen, navigate to the Settings page by pressing the (insert gear icon)
2. Select the About page
3. Select ‘Advanced Z-Wave Utilities’
4. Select ‘Learn Mode’, this will put the bridge into learn mode to receive information from another Z-
Wave controller. Transferring network information from another Z-Wave controller to this bridge
can commonly be referred to as replication. Any devices that are not on the supported device list
may not work properly with the Walmart bridge.
The WiFi Bridge’s DSK (device specific key) is located in the WiFi bridge details page and can be accessed by
going to Settings > Garage Door Controller Device > WiFi bridge > Bridge details.
If this controller is the primary controller for your network, resetting it will result in the nodes in your
network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in
the network. If this controller is being used as a secondary controller in the network, use this procedure to
reset this controller only in the event that the network primary controller is missing or otherwise inoperable.
To factory reset the WiFi Bridge, which will also factory reset and delete all Z-Wave network information,
press and hold the button on the back of the bridge for 20 seconds.