Waring BB155 SERIES User manual

BB155/BB155S SERIES
INSTRUCTION MANUAL
MANUAL DE INSTRUCCIONES
DE LAS LICUADORAS
DE LA SERIE BB155/BB155S
DIRECTIVES D’UTILISATION
DES MÉLANGEURS
DE LA SÉRIE BB155/BB155S
For your safety and continued enjoyment of this product,
always read the instruction book carefully before using.
Para su seguridad y para disfrutar plenamente de este producto,
siempre lea las instrucciones cuidadosamente antes de usarlo.
An que votre appareil vous procure en toute sécurité beaucoup de
satisfaction, lire attentivement le mode d’emploi avant de l’utiliser.

2
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions
should always be followed, including the following:
1. READ ALL INSTRUCTIONS.
2. Unplug from outlet when not in use, before putting
on or taking off parts, and before cleaning.
3. To protect against electrical hazards, do not immerse
the blender base in water or other liquids.
4. This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
5. Children should be supervised to ensure that they
do not play with the appliance.
6. Avoid contact with moving parts.
7. Do not operate any appliance with a damaged cord or
plug or after the appliance malfunctions or is dropped
or damaged in any manner. Return appliance to the
nearest authorized service facility for examination,
repair or electrical or mechanical adjustment.
8. The use of attachments, including canning jars, not
recommended by the appliance manufacturer may
cause hazards.
9. Do not use outdoors.
10. Do not let cord hang over edge of table or counter,
where it can inadvertently be pulled on or tripped over,
or touch hot surfaces, which could damage the cord.
11. Keep hands and utensils out of container while
blending, to prevent the possibility of severe personal
injury and/or damage to the blender. A rubber scraper
may be used, but must be used only when the blender
is not running.

3
12. Blades are SHARP. Handle carefully.
13. Never place cutting assembly or cutting blades on base
without container properly attached.
14. Always operate blender with cover in place.
15. Always operate blender with jar pad in place.
16. CAUTION:This blender is not intended for use with hot
liquids or ingredients.
17. Do not ll above MAX FILL line for blending.
18. Not for waterjet cleaning.
19. Ensure the jar coupler and motor coupler are aligned
and engaged before operating. If unable to engage,
remove jar and shake contents, then try again.
20. The jar coupler and motor coupler may be hot after
running; do not touch.
21. Always use HIGH speed for crushing ice.
22. If the jar overows during blending, there is too much
liquid/ingredients in the jar. Stop blending, remove
enough liquid/ingredients to below MAX FILL line, and
continue blending. Do not operate if overowing.
23. DO NOT use carbonated liquids in the blender jar or
any blending container. Using carbonated liquids in
the blender jar or any blending container may result in
injury.
24. DO NOT blend oil or oil-based products such as peanut
butter for greater than 5 minutes.
25. Never remove blender jar from base unit until the blade
and coupling have completely stopped.
SAVE THESE INSTRUCTIONS

4
GROUNDING INSTRUCTIONS
• For your protection, Waring®Commercial Blenders are
equipped with a 3-conductor cord set.
• 120 volt units are supplied with a molded 3-prong
grounding-type plug and should be used in combination
with a properly connected grounding-type outlet, as
shown in Figure 1.
If a grounding-type outlet is not available, an adapter, shown
in Figure 2, may be obtained to enable a 2-slot wall outlet to
be used with a 3-prong plug.
Referring to Figure 3, the adapter must be grounded by
attaching its grounding lug under the screw of the outlet
cover plate.
CAUTION: Before using an adapter, it must be determined
that the outlet cover plate screw is properly grounded. If in
doubt, consult a licensed electrician.
Never use an adapter unless you are sure it is properly
grounded.
NOTE: Use of an adapter is not permitted in Canada.

5
BLENDER JAR ASSEMBLY INSTRUCTIONS
1. When assembling blade
assembly to jar, beware of the
blades as they are very sharp.
2. Position rubber seal over blade
assembly so that it sits in
between the ats of the blade
assembly and the jar.
3. Insert blade assembly with
rubber seal into the bottom hole
of the jar.
NOTE: To avoid leaking while
blending, be sure the rubber
seal is positioned in between the
blade assembly and the jar. HINT:
Assembling the jar is easier when
the bottom of the jar is facing up.
4. Screw the collar clockwise onto
the jar until it tightly secures the
blade assembly and seal to the jar.
BB155 OPERATION
1. Before starting, make sure
that the blender is unplugged.
2. Always be sure container is properly assembled before
adding ingredients.
3. Put ingredients into container and cover it. Do not ll
above MAX FILL line.
4. With the switch in the OFF position,
place container on blender base. Be
sure container is fully seated and that
drive coupling is properly engaged.
Plug blender cord into outlet.
5. This blender has 2 speed settings:
HI and LO. Press toggle switch to desired position. To
crush ice, always use HI speed setting.

6
6. When nished blending, set toggle switch to OFF
position.
7. Allow motor to come to a complete stop before
removing container from blender base. Never place
the container on the motor base or remove it from
the motor base while motor is running.
8. Always hold container with one hand when starting and
while blending. Never operate without jar lid.
9. Wash and dry container after each use. See Cleaning
and Sanitizing Instructions.
10. Unplug to turn off all power to blender.
CLEANING AND SANITIZING INSTRUCTIONS
THE CONTAINER MUST BE CLEANED AND DRIED AFTER
EACH USE OF THE BLENDER ACCORDING TO THE
FOLLOWING INSTRUCTIONS.
FAILURE TO DO SO MAY ALLOW RESIDUE OF
PROCESSED MATERIAL TO COLLECT ON THE INTERNAL
SEALS OF THE BLADE ASSEMBLY, RENDERING THEM
INEFFECTIVE.
• Wash, rinse, sanitize and dry container prior to initial use
and whenever it will not be used again within a period of
1 hour.
• Wash and rinse container and blade assembly after
each use.
• Clean and sanitize motor base prior to initial use and after
each use.
• Washing solutions based on non-sudsing detergents and
chlorine-based sanitizing solutions having a minimum
chlorine concentration of 100 PPM are recommended.

7
The following washing, rinsing, and sanitizing solutions, or
their equivalents, may be used.
SOLUTION PRODUCT DILUTION IN WATER TEMPERATURE
Washing Diversey®Wyandotte 4 Tablespoons Hot 115˚F (46˚C)
Diversol®BX/A or CX/A /Gallon
Rinsing Plain Water Warm 95˚F (35˚C)
Sanitizing Clorox®1 Tablespoon/Gallon Cold 50˚F–70˚F
Institutional Bleach (10˚C–21˚C)
• In repetitive batch-processing applications, frequent
cleaning of the container will prolong the life of the blade
assembly. In no case should actual running time between
cleanings exceed one-half hour.
• Do not use container to store processed foods or
beverages.
TO WASH AND RINSE CONTAINER
1. REMOVE CONTAINER FROM MOTOR BASE.
Remove lid. Rinse container interior and lid under
running water. Add washing solution to container.
Scrub and ush out the container interior and lid to
dislodge and remove as much food residue as
possible. Empty container.
2. Wipe down exterior of container with a soft cloth or
sponge dampened with washing solution. Wash lid
and lid insert in fresh washing solution. Fill container
one-quarter full with fresh washing solution, cover
(with lid only), place on motor base and run on HIGH
speed for two (2) minutes. Empty container.
3. Repeat step (2) using clean rinse water in place of
washing solution.

8
IMPORTANT
NOTE: IN ORDER TO MINIMIZE POSSIBILITY OF
SCALDING, TEMPERATURE OF WASHING SOLUTION
AND RINSE WATER MUST NOT EXCEED 115˚F (46˚C), AND
QUANTITY USED MUST NOT EXCEED ONE-QUARTER
CONTAINER FULL.
TO SANITIZE AND DRY CONTAINER
1. Wipe down exterior of container with a soft cloth
or sponge dampened with sanitizing solution.
2. Fill container with sanitizing solution, cover, place on
motor base, and run on HIGH speed for one (1) minute.
Empty container. Dislodge any residual moisture from
blade assembly by placing empty container on motor
base and running on HIGH speed for two (2) seconds.
3. Sanitize lid and lid insert by immersing in sanitizing
solution for two (2) minutes.
4. Do not rinse container, lid, or lid insert after sanitizing
is completed. Allow parts to air-dry.
TO CLEAN AND SANITIZE MOTOR BASE
1. UNPLUG POWER CORD. Wipe down exterior surfaces
of motor base with soft cloths or sponges dampened
with washing solution, rinse water, and sanitizing
solution. Prevent liquid from running into motor base
by wringing all excess moisture from cloths or sponges
before using them.
DO NOT IMMERSE MOTOR BASE IN WASHING SOLUTION,
RINSE WATER OR SANITIZING SOLUTION.
2. Allow motor base to air-dry before using.

9
SERVICE
Refer to the list of Authorized Service Centers enclosed
with your Waring®Commercial Blender for the name of the
nearest Service Center, or write to:
Waring Factory Service Center
P.O. Box 3201
314 Ella T. Grasso Avenue
Torrington, CT 06790
1-800-492-7464
Ship blenders for repair to the above address or to an
Authorized Service Center. Do not ship to a Waring Sales
Ofce.
NOTE: If your application involves the processing of
biologically active material, we request that any items
returned for service be sterilized before being shipped.
Such items must be clearly identied as having been
sterilized, both by a tag on the item itself and by a statement
in the accompanying correspondence. Waring will not
accept delivery of any return unless it is so identied.
Replacement parts for your out-of-warranty repairs are
obtainable at the address below.
LIMITED TWO YEAR WARRANTY
Waring warrants every new Waring®Commercial Blender
to be free from defects in material and workmanship for a
period of two years from the date of purchase when used
with foodstuffs, nonabrasive liquids (other than detergents)
and nonabrasive semi-liquids, providing it has not been
subject to loads in excess of the indicated rating. In addition,
the motor in this appliance has a full three year warranty.
Under this warranty, Waring will repair or replace any part
that, upon our examination, is defective in materials or
workmanship, provided the product is delivered prepaid
to the Waring Service Center at: 314 Ella T. Grasso Ave.,
Torrington, CT 06790, or any Authorized Service Center.

10
This warranty does not: a) apply to any product that has
become worn, defective, damaged or broken due to misuse
or due to repairs or servicing by other than the Waring
Service Center or an Authorized Service Center, or due
to abuse, misuse, overloading or tampering; or b) cover
incidental or consequential damages of any kind.
The one year warranty is applicable only to appliances
used in the United States or Canada; this supersedes all
other express product warranties or warranty statements.
For Waring products sold outside of the U.S. and Canada,
the warranty is the responsibility of the local importer
or distributor. This warranty may vary according to local
regulations.
Warning: This warranty is void if appliance is used on
Direct Current (DC).
Waring Commercial
314 Ella T. Grasso Avenue
Torrington, CT 06790
1-800-4-WARING
www.waringcommercialproducts.com