Waring CB15 SERIES User manual

1 GALLON BLENDERS WITH SPIGOT
LICUADORAS DE 4 L CON GRIFO
MÉLANGEURS DE 4 L AVEC ROBINET
120V
For your safety and continued enjoyment of this product,
always read the instruction book carefully before using.
Para su seguridad y para disfrutar plenamente de este producto,
siempre lea las instrucciones cuidadosamente antes de usarlo.
Afin que votre appareil vous procure en toute sécurité beaucoup de satisfaction,
lire attentivement le mode d’emploi avant de l’utiliser.
CB15 SERIES
SERIE CB15
SÉRIE CB15

2
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions
should always be taken, including the following:
1. READ ALL INSTRUCTIONS.
2. Unplug from outlet when not in use, before putting
on or taking off parts, and before cleaning.
3. To protect against electrical hazards, do not immerse
the blender base in water or other liquids.
4. Avoid contact with moving parts.
5. Do not operate any appliance with a damaged cord or
plug, or after the appliance malfunctions or is dropped
or damaged in any manner. Return appliance to the
nearest authorized service facility for examination, repair
or electrical or mechanical adjustment.
6. The use of attachments, including canning jars, not
recommended by the appliance manufacturer may
cause hazards.
7. Do not use outdoors.
8. Do not let cord hang over edge of table or counter, or
touch hot surfaces.
9. Keep hands and utensils out of container while blending
to prevent the possibility of severe personal injury and/or
damage to the blender. A rubber scraper may be used
but must be used only when the blender is not running.
10. Blades are sharp. Handle carefully.
11. Always operate blender with cover in place.
12. When blending hot liquids, completely remove the
stopper in the cover before turning on the blender.
See Hot Blending Instructions, page 12.
13. This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge.

3
14. Children should be supervised to ensure that they do not
play with the appliance.
15. DO NOT use carbonated liquids in the blender jar or
any blending container. Using carbonated liquids in the
included blender jar or any other compatible blender jar
may result in injury.
16. DO NOT blend oil or oil-based products such as peanut
butter for greater than 5 minutes.
17. Never remove blender jar from base unit until the blade
and coupling have completely stopped.
18. Spigot assembly must be handwashed only. Do not run
the spigot through the dishwasher.
19. The contents of the blender cannot reach beyond 140˚F
when operating with a spigot. Note that when blending
the temperature of the contents will increase due to the
friction of the blade.
SAVE THESE INSTRUCTIONS
SPECIFICATIONS
• Capacity: 4 Litre Working Capacity
• Rating: 120 Volts–60HZ–Single Phase AC –15.0 Amps.
(U.S. models only)
• Base: Die-cast – grey coating
• Container: Stainless steel with stainless steel blades –
rubber clamp-on lid
• Bearing: High-performance ball bearing
• Cord: 7 foot (2.44 m) – 3-conductor ground cord with
strain relief in base
• Overall Height: 26 inches (66 cm)
• Weight: 38 pounds (17.2 kg) net
Shipping Weight 41 pounds (18.6 kg)
• cETLus, NSF, Listed
• Operating Cycle: 3 min ON/1 min OFF

4
120V GROUNDING INSTRUCTIONS
For your protection, this appliance is equipped with a
3-conductor cordset.
120-volt units are supplied with a molded 3-prong
grounding-type plug (NEMA 5-15P) and should be used
in combination with a properly connected grounding type
outlet as shown in Figure 1.
If a grounding type outlet is not available, an adapter, shown
in Figure 2, may be utilized to enable a 2-slot wall outlet to
be used with a 3-prong plug. (Note: Use of an adapter is
not permitted in Canada and Europe.)
Referring to Figure 3, the adapter must be grounded by
attaching its grounding lug under the screw of the outlet
cover plate.
Caution: Before using an adapter, it must be determined
that the outlet cover plate screw is properly grounded. If in
doubt, consult a licensed electrician. Never use an adapter
unless you are sure it is properly grounded.
Green/Yellow: Earth Ground • Blue: Neutral • Brown: Live
Note: User-installed cordset plugs are not permitted
in Europe.

5
SPIGOT ASSEMBLY (FOR SF MODELS ONLY)
Your spigot assembly includes the main spigot housing,
O-ring and rubber insert.
1. Plastic Feed Cap
2. Vinyl Lid
3. Metal Clamps
4. Spigot Adapter
5. O-ring
6. Spigot housing
7. Lever
8. Rubber Insert
1
2
3
4
8
7
6
5

6
SPIGOT ASSEMBLY (FOR SF MODELS ONLY)
Your spigot assembly includes the main spigot housing,
O-ring and rubber insert.
The O-ring comes assembled
in the jar spigot adapter but
can be removed for cleaning.
Always make sure the O-ring
is positioned securely in the
adapter on the jar before
inserting and operating the
spigot function. Figure 1.
The rubber insert has two loops
on the inside to t the lever
(refer to gure 2). The lever only
needs to be positioned into the
bottom loop. In the event that
one loop breaks, you can ip
the insert upside down and use
the other loop.
To assemble the rubber insert
pinch both sides as seen in
gure 3 and position the insert
inside the housing so that the
lever slides inside the rubber
insert and the bottom loop (for
the lever) is near the spigot
hole. Be sure that the bottom
of the rubber insert is ush
with the bottom of the spigot
housing.
Push the bottom of the lever
through the bottom loop of the
rubber insert.
g. 1
g. 2
g. 3
g. 4

7
Once assembled, insert the
spigot into the adapter on the
jar and rotate clockwise until
the spigot completely stops
as shown in gure 5.
CB15/CB15SF OPERATION
1. Before starting, make sure that the blender cord is
unplugged.
2. Position container assembly on
motor base so that it is rmly
seated and not tilting to one side.
Plug blender cord into outlet.
3. Put ingredients into container.
Always add liquid ingredients rst, unless otherwise
specied in recipe. Do not ll above MAX line.
Place cover securely on container and fasten the
cover clamps.
4. Press the STANDBY button to turn on the blender.
Green LED will illuminate. For continuous operation,
press either the LOW, MED, or HIGH button. When
nished blending, press STOP. For momentary
operation, press the PULSE button; motor will run
on HIGH speed until the button is released.
Note: Your CB15 utilizes a Slow Start™ feature.
When pressing MED or HIGH, the unit will start in the
LOW position for 1 second and then switch to the
setting selected. This allows for a more even blending
of ingredients in container.
5. Always hold container with one hand when starting
and while blending. Never operate without jar lid
properly clamped in place.
g. 5

8
6. Allow motor to come to a complete stop before
removing container. Never place the container on the
motor base or remove it from the motor base while
the motor is running.
7. Press the STANDBY button again to turn off the
blender.
8. Remove the container from the motor base and
empty the contents.
9. Wash and dry container after each use, according to
Cleaning and Sanitizing Instructions, page 13.
10. Not for waterjet cleaning.
11. The use of ear protection is recommended during
extended operating periods.
Spigot Instructions
When pouring jar contents through the spigot, simply
push the lever toward the blender jar. If contents are
too thick, it can be difcult to pour through the spigot.
Running the blender on LOW while pouring can help
the ow. Make sure to always have the lid positioned on
the blender with the clamps locked when running the
blender.
CB15T/CB15SF OPERATION
1. Before starting, make sure that the blender cord is
unplugged.
2. Position container assembly
on motor base so that it is
rmly seated and not tilting
to one side. Plug blender cord
into outlet.

9
3. Put ingredients into container. Always add liquid
ingredients rst, unless otherwise specied in recipe.
Do not ll above MAX line. Place cover securely on
container and fasten the cover clamps.
4. Press the STANDBY button to turn on the blender.
Press the UP arrow or DOWN arrow. The initial time
will be 10 seconds.
5. Push the UP arrow to set the time required. The timer
will advance only in 10-second intervals. Timer can be
set to the maximum of 3 minutes.
6. Select and press a speed button; the blender will
start and run for that selected time. It will count
down in 1-second intervals and stop at 0. NOTE: If
you want to increase or decrease time while timer is
counting down, press UP or DOWN arrows. Timer will
increase or decrease in 10-second intervals. After
5 seconds the timer will turn off and return to manual
mode.
7. When using the timer again, the initial time will be the
last time set. NOTE: If unit has been unplugged, the
timer will default back to 10 seconds.
8. Always hold container with one hand when starting
and while blending. Never operate without container
lid properly clamped in place.
9. Allow motor to come to a complete stop before
removing container. Never place the container on the
motor base or remove it from the motor base while
the motor is running.
7. Press the STANDBY button again to turn off the
blender.
8. Remove the container from the motor base and
empty the contents.

10
9. Wash and dry container after each use, according to
Cleaning and Sanitizing Instructions, page 13.
10. Not for waterjet cleaning.
11. The use of ear protection is recommended during
extended operating periods.
Spigot Instructions
When pouring jar contents through the spigot, simply
push the lever toward the blender jar. If contents are
too thick, it can be difcult to pour through the spigot.
Running the blender on LOW while pouring can help
the ow. Make sure to always have the lid positioned on
the blender with the clamps locked when running the
blender.
CB15V/CB15SF OPERATION
1. Before starting, make sure that the blender cord is
unplugged.
2. Position container assembly
on motor base so that it is
rmly seated and not tilting
to one side. Plug blender cord
into outlet.
3. Put ingredients into container. Always add liquid
ingredients rst, unless otherwise specied in recipe.
Do not ll above MAX line. Place cover securely on
container and fasten the cover clamps.
4. Press the green STANDBY button to turn on the
blender. Green LED will illuminate and remain steady.
Select the desired speed with the variable speed
control knob. Press the red START/STOP button to
begin blending. You may change the speed with the
variable speed control knob anytime during blending.
When nished blending, press START/STOP button.