Waring Mx series User manual

XTREME®HI-POWER BLENDER
LICUADORA DE ALTA POTENCIA XTREME®
MÉLANGEUR HAUTE PUISSANCE XTREME®
MX SERIES
SERIE MX
SÉRIE MX
For your safety and continued enjoyment of this product, always read
the instruction book carefully before using.
Para su seguridad y para disfrutar plenamente de este producto, siempre lea
cuidadosamente las instrucciones antes de usarlo.
An que votre appareil vous procure en toute sécurité beaucoup de satisfaction,
lire attentivement le mode d’emploi avant de l’utiliser.

2
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
taken, including the following:
1. READ ALL INSTRUCTIONS.
2. Always unplug from outlet when not in use, prior to handling, before
putting on or taking off parts, and before cleaning.
3. To protect against electrical hazards, do not immerse the blender base
in water or other liquids.
4. This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge. Children should be supervised to ensure
they do not play with the appliance.
5. Avoid contact with moving parts.
6. Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions or is dropped or damaged in any manner.
Return appliance to the nearest authorized service facility for
examination, repair, or electrical or mechanical adjustment.
7. The use of attachments, including canning jars, not recommended by the
appliance manufacturer, may cause hazards.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter, or touch hot surfaces.
10. Keep hands and utensils out of container while blending to prevent the
possibility of severe personal injury and/or damage to the blender.
A rubber scraper may be used, but must be used only when the blender
is not running.
11. Blades are sharp. Handle carefully.
12. Always operate blender with cover in place.
13. When blending hot liquids, remove the center piece of the two-piece
cover. See Hot Blending Instructions.
14. The use of ear protection is recommended during extended
operating periods.
15. Before First Use: Clean blender and jar per cleaning and sanitizing
instructions, pages 11–12.
16. The appliance must be positioned so that the plug is accessible.
17. DO NOT use carbonated liquids in the blender jar or any blending
container. Using carbonated liquids in the blender jar or any blending
container may result in injury.
18. DO NOT blend oil or oil-based products such as peanut butter for
longer than 5 minutes.
19. Never remove blender jar from base unit until the blade and coupling
have completely stopped.
SAVE THESE INSTRUCTIONS

3
MX MECHANICAL SWITCHES
1. Before starting, make sure that the blender is
unplugged and container is not positioned on
the blender.
2. Put ingredients into container and cover it. Do not
fill above MAX fill line.
3. With the unit in STANDBY position, place
container on blender base. Be sure container is
fully seated and that drive coupling is properly
engaged. Plug blender cord into outlet.
4. This blender has 2 speed settings: HI and LO . Press paddle switch
to desired position. To crush ice quickly, use HI speed setting.
5. When finished blending, set paddle switch to STANDBY position.
6. This blender is equipped with a PULSE option. Hold paddle switch
down to engage PULSE function. Unit will run on HI speed until the
paddle switch is released.
7. Allow motor to come to a complete stop before removing container from
blender base. Never place the container on the motor base or remove it
from the motor base while motor is running.
8. Always hold container with one hand when starting and while blending.
Never operate without jar lid.
9. Wash and dry container after each use. See Cleaning and Sanitizing
Instructions.
MX ELECTRONIC TOUCHPAD SWITCHES
WITHOUT SOUND ENCLOSURE
1. Before starting, make sure that the blender is
unplugged and container is not positioned on
the blender.
2. Put ingredients into container and cover it. Do not
fill above MAX fill line.
3. Place container on blender base. Be sure container
is fully seated and that drive coupling is properly
engaged. Plug blender cord into outlet.
4. This blender is equipped with an electronic membrane keypad. The
keypad has a main power STANDBY button, plus HI , LO , STOP
and PULSE buttons.
5. Press the STANDBY button to turn on the blender. Green LED will
illuminate. For continuous operation, press either LO or HI button.
When finished blending, press STOP . For momentary operation,
press the PULSE button; motor will run on HI speed until the
button is released.
NOTE: Your MX Electronic Blender uses a Slow Start™feature. When
pressing HI , the unit will start in the LO speed for 2 seconds and
then switch to HI speed. This allows for a more even blending of
ingredients in container.

4
6. Allow motor to come to a complete stop before removing container from
blender base. Never place the container on the motor base or remove it
from the motor base while motor is running.
7. Always hold container with one hand when starting and while blending.
Never operate without jar lid.
8. Wash and dry container after each use. See Cleaning and Sanitizing
Instructions.
9. To turn unit off, press STANDBY button. Green LED light will go off.
MX ELECTRONIC TOUCHPAD SWITCHES WITH TIMER
1. Before starting, make sure that the blender is
unplugged and container is not positioned on
the blender.
2. Put ingredients into container and cover it.
Do not fill above MAX fill line.
3. Place container on blender base. Be sure container
is fully seated and that drive coupling is properly
engaged. Plug blender cord into outlet.
4. This blender is equipped with an electronic membrane keypad. The
keypad has a main power STANDBY button, plus HI , LO , STOP
and PULSE buttons and a 30-second countdown timer with up
and down arrows to set time.
5. Press the STANDBY button to turn on the blender. Green LED will
illuminate. The electronic timer will indicate 10 seconds (default). Press
the up or down arrow to set the desired time. The electronic
timer will indicate run time in 5-second intervals up to a maximum of
30 seconds. After the desired time is set, press HI or LO to start the
blender. The timer will count down to 0 in 1-second intervals and blender
will shut off. Pressing the PULSE button, the STOP button or the
STANDBY button will override the timer and the blender will stop
regardless of time left on timer.
NOTE: If you want to increase or decrease time while timer is counting
down, press up or down arrows. Time will increase or decrease
in 5-second intervals.
6. If the blender is not used for 5 seconds, the timer function will turn off
and return to manual mode. To reactivate timer, press up or down
arrows. When using the electronic timer again, the initial time will be the
last time set. Note: If unit has been turned off or unplugged, the timer
will default back to 10 seconds.
7. For continuous operation, press either LO or HI button. When
finished blending, press STOP . For momentary operation, press
the PULSE button. Motor will run on HI speed until the button
is released.
NOTE: Your MX Electronic Blender uses a Slow Start™feature. When
pressing HI , the unit will start in the LO speed for 2 seconds and
then switch to HI speed. This allows for a more even blending of
ingredients in container.

5
8. Allow motor to come to a complete stop before removing container from
blender base. Never place the container on the motor base or remove it
from the motor base while motor is running.
9. Wash and dry container after each use. See Cleaning and Sanitizing
Instructions.
10. To turn the unit off, press STANDBY button. Green LED light will
go off. MX VARIABLE SPEED OPERATION
Warning – This is a Class A product. In a domestic environment this
product may cause radio interference, in which case the user may be
required to take adequate measures.
1. Before starting, make sure that the blender is
unplugged and container is not positioned on the
blender.
2. Put ingredients into container and cover it. Do not
fill above MAX fill line.
3. With the unit in STANDBY position, place
container on blender base. Be sure container is fully seated and that
drive coupling is properly engaged. Plug blender cord into outlet.
4. This blender has variable speed controls. Set blender to desired speed
between 1 and 10.
5. The left paddle switch defaults to the VARIABLE setting in order to use
the speed adjustment option. Press right paddle switch up to the ON
position.
6. When finished blending, set paddle switch to STANDBY position.
7. This blender is equipped with a PULSE option. Holding left paddle
switch in down position will activate VARIABLE PULSE function (Pulse
speed controlled by knob). If ON/STANDBY switch is set to the ON
position and PULSE switch is activated, then PULSE will operate
at maximum speed of 30,000 RPM. Once PULSE paddle switch is
released, speed will continue to run at variable speed setting.
8. Allow motor to come to a complete stop before removing container
from blender base. Never place the container on the motor base or
remove it from the motor base while motor is running.
9. Always hold container with one hand when starting and while blending.
Never operate without jar lid.
10. Wash and dry container after each use. See Cleaning and Sanitizing
Instructions.
MX REPROGRAMMABLE CONTROL SETTINGS
1. Before starting, make sure that the blender is unplugged and container
is not positioned on the blender.
2. Put ingredients into container and cover it. Do not fill above MAX Fill
line.
3. Place container on blender base. Be sure container is fully seated and
that drive coupling is properly engaged. Plug blender cord into outlet.

6
4. The motor speed can be adjusted by pressing
the or Speed buttons. Speed ranges from
5% to 100%.
100% 20,000 RPM
50% 10,000 RPM
5% 1,000 RPM
The Speed Up button will increase the motor speed display in 1%
increments and the Speed Down button will decrease the motor
speed display in 1% increments. Holding down either button will quickly
scroll through speeds.
Using the Speed Up and Speed Dow buttons, set desired motor
speed. If no speed is selected, motor will default to 100%.
NOTE: The motor does not run at the newly set speed until the START/
STOP button is pressed. If START/STOP button is not pressed
within 5 seconds, the new speed setting will be stored for next use and
the blender will return to STANDBY mode; the display will once again
read “PRESS ANY BUTTON TO BLEND.”
5. Press START/STOP button to run the blender. Blender will run
continuously at the set speed. The LCD will display the motor speed in
percentage. Default speed (percentage) is at 100%. Motor speed can be
changed while blender is running by simply pressing Speed Up or
Speed Down button.
6. To stop continuous blending operation, press START/STOP button or
press any of the program buttons.
PULSE FEATURES
Your unit comes equipped with two PULSE options: Normal Pulse and
Maximum Pulse . Note: The Pulse buttons are momentary switches —
once released, the unit will shut off.
1. To use Max Pulse option, press the button. This will run the motor
at 150% speed. The LCD will read “MAX PULSE SPEED: 150%.”
2. To use Normal Pulse option, press the button. This will run the motor
at 100% speed. The LCD will read “NORM PULSE SPEED: 100%.”
3. The blender allows you to set the pulse to your desired speed. While
blending at Normal Pulse speed, the motor can be adjusted. To do this,
hold the Normal Pulse button and press Speed Up or Speed
Down button to adjust the blending speed. The LCD will show the
setting speed and motor speed will change.
NOTE: The speed can be set from 5% to 100%. Once the Pulse
button is released, the motor will shut off and the blender will return to
STANDBY mode. The changed pulse speed will be stored in memory to
replace the default speed off 100%.

7
REPROGRAMMABLE STATIONS
1. There are 4 Program buttons for four reprogrammable beverage stations
for easy operation and consistent results. The factory-set stations are
programmed as listed below:
Liquid drinks
Frozen drinks
Ice cream drinks
Smoothies
2. To run any of the above preset programs, blender must be in
STANDBY mode.
3. Press desired Program button to start the blender. The motor will run at
the preset speed within the preset blending time. The LCD will show time
remaining. Once the blender counts down to 0, the motor will stop
running and the blender will return to STANDBY mode and prompt
“PRESS ANY BUTTON TO BLEND,” to begin another function.
NOTE: To terminate a blending program, simply press START/STOP
button or any of the Program buttons. After doing this, the blender will
return to STANDBY mode and LCD will prompt “PRESS ANY BUTTON
TO BLEND.”
REPROGRAMMING BEVERAGE STATIONS
Users can add 4 new programs to meet their needs. A program can
consist of several sections, each with a different speed and running time.
For example, can be replaced with a new program that has 3 sections,
as shown below:
Section 1: speed = 75%; time = 30 seconds
Section 2: speed = 100%; time = 20 seconds
Section 3: speed = 50%; time = 20 seconds
The program has the following limitations:
Speed: 5% to 100%
Time: 5 to 90 seconds
Total running time in a program cannot exceed 90 seconds, i.e., sum
of the sections cannot be longer than 90 seconds.
NOTE: The button will act as the enter key to proceed to the next step
during the reprogramming process.
1. To enter new program, press both Speed Up and Speed Down
buttons simultaneously while unit is in STANDBY mode. The blender will
enter new programming mode and the LCD will prompt “ADD NEW
PROGRAM.”
2. Next, you will need to set values. Press the Program button you want
to replace (e.g., 1–4). The LCD will prompt “USE UP/DOWN TO SET
SPEED: 25%.”

8
NOTE: 25% is the default speed setting in the reprogramming mode.
3. Press Speed Up or Speed Down button to set the speed value.
The increment is 1% (150 RPM). Press and hold the button to quickly
scroll through speeds. The speed can be set between 5% and 100%.
4. Once required speed is reached, press button or wait 5 seconds
to confirm setting. The LCD will now prompt “USE UP/DOWN TO SET
TIME.” NOTE: Five seconds is the default time setting in the
reprogramming mode.
5. Use Speed Up or Speed Down button to set the time value (up to
90 seconds). Once 90 seconds are reached, pressing Speed Up will
not increase the value and the LCD will prompt “MEMORY LIMIT” for
2 seconds.
6. Press button or wait 5 seconds to confirm the setting. When the
blending time is confirmed, the LCD will prompt SELECT ANOTHER
SPEED. Repeat steps 3–5 if additional processing is needed.
NOTE: When pressing Speed Up or Speed Down buttons to set
speed for next section, the LCD will prompt “USE UP & DOWN TO SET
SPEED: 25%.”
7. To save the new program settings, press both Speed Up and Speed
Down buttons simultaneously. The LCD will prompt NEW PROGRAM
(PROG #) SAVED for 5 seconds. The blender will return to STANDBY
mode and the LCD will prompt “PRESS ANY BUTTON TO BLEND.”
NOTE: If no button is pressed for 60 seconds when prompted to “ADD
NEW PROGRAM,” the blender will exit NEW PROGRAM mode and will
return to STANDBY mode. The new program will not be stored.
8. To run new programs, simply press the desired Program button and the
blender will run the program set by the user. The LCD will display NEW
PROGRAM # and will count down the set time.
RESTORING FACTORY-SET BEVERAGE STATIONS
1. To restore factory-set default beverage stations, press both
Speed Up and Speed Down buttons. LCD will prompt “ADD NEW
PROGRAM.”
2. Press button. LCD will prompt “RESTORE DEFAULT PROGRAMS.”
3. Press button to confirm and save. The LCD will display the logo for
3 seconds.
4. The unit will return to STANDBY mode and the LCD will prompt “PRESS
ANY BUTTON TO BLEND.”
NOTE: The STOP key will abort this process at any point before
restoring default programs is confirmed.

9
DRINK COUNTER
Your reprogrammable blenders are equipped with a drink counter to keep
track of daily drink totals and total drink counts for your machine. To display
the counts, hold program buttons & simultaneously for 3 seconds.
Your display will read:
DAILY COUNT XXXX
TTL COUNT XXXXX
Daily Count will display the number of drinks mixed per day. Total Count
is the accumulation of all drinks made since first use of the blender.
The Daily Count can be reset by holding in Program buttons &
simultaneously for 3 seconds, then pressing ON/OFF button for 3 seconds.
Daily Count will reset to zero and Total Count will remain unchanged.
If Total Count needs to be reset, call your nearest Waring authorized service
facility for information.
NOTE: Use of the PULSE features will not add to the daily or total drink
counts. RESETTING THERMAL PROTECTION
• The blender you have purchased is equipped with an Automatic Reset
Switch to protect the motor from overheating.
• If your blender stops running under heavy use, turn the power switch to the
STANDBY or OFF position and unplug the power cord. Empty the blender
container of all its contents and allow approximately 5 minutes for the
motor to cool down.
• Plug the power cord back into the outlet and continue blending.
IMPORTANT — HOT BLENDING INSTRUCTIONS
To minimize the possibility of being scalded when blending hot materials,
the following precautions and procedure must be observed.
•Hot materials are those that are 100°F (38°C) or hotter.
•Limit the amount of materials processed to 1 pint.
•Completely remove the center portion of the two-piece container lid before
starting motor (this will allow venting of the rapidly heated and expanded
air inside the container when blender is running).
•Always start blending on lowest speed setting, and then progress to
desired speed.
•Never stand directly over blender when it is being started or while it
is running.

10
INSTALLING THE SOUND ENCLOSURE
NOTE: If you are installing a sound enclosure as an optional accessory,
remove the standard jar pad to access the screw holes on the upper
housing. This jar pad will not fit properly with the sound enclosure. To remove
it, peel it back, starting in the corner and working your way over the drive
coupling until it is completely off the base unit, as seen in Figures 1, 2 and 3.
Once you have finished removing the standard jar pad OR if your blender
came packed with a sound enclosure, follow these instructions:
Step 1: Find the 3 screw holes located on the left, back and right sides of
the upper housing as seen in Figures 4, 5 and 6.
Step 2: Place the base of the sound enclosure on the motor housing so the
screw holes on the enclosure line up with the screw holes on the
base. Use a Phillips-head screwdriver and the 3 screws included
with sound enclosure to secure the enclosure to the base unit in the
3 locations as seen in Figures 7, 8 and 9.
Step 3: Once the sound enclosure is secured tightly, select the custom jar
pad (included with sound enclosure). Please note the standard jar
pad will NOT fit properly with the sound enclosure. The correct
custom jar pad has a recessed area around the outer edge. It also
has a curved front with tabs on the sides, as seen in Figures 10, 11,
and 12. This curved area should face the front of the blender.
Step 4: Attach custom jar pad included with sound enclosure onto upper
housing with the curve facing out, as seen in Figure 13. Press tightly
around coupling to secure custom jar pad onto upper housing, as
seen in Figures 14 and 15.
Figure 1 Figure 2 Figure 3 Figure 4 Figure 5
Figure 6 Figure 7 Figure 8 Figure 9
Figure 11 Figure 12 Figure 13 Figure 14 Figure 15
Figure 10

11
REMOVING THE SOUND ENCLOSURE
To remove the sound enclosure, unplug your blender and follow these steps:
1. Open sound enclosure and remove blender container.
2. Remove front portion of sound enclosure by disengaging both sides at
the pivot point.
2. Remove rubber jar pad.
4. Remove 3 screws from blender base and remove sound enclosure.
TURNING OFF YOUR BLENDER
Whether your blender is in STANDBY mode, NEW PROGRAM mode, or
the motor is running, pressing the ON/OFF button will stop the unit
from running and will turn the power off. The LCD display will turn off.
NOTE: All programs and current settings will be restored next time you
turn unit on.
CLEANING AND SANITIZING INSTRUCTIONS
THE CONTAINER MUST BE CLEANED AND DRIED AFTER EACH USE
OF THE BLENDER ACCORDING TO THE FOLLOWING INSTRUCTIONS.
FAILURE TO DO SO MAY ALLOW RESIDUE OF PROCESSED MATERIAL
TO COLLECT ON THE INTERNAL SEALS OF THE BLADE ASSEMBLY,
RENDERING THEM INEFFECTIVE.
•Wash, rinse, sanitize and dry container prior to initial use and whenever
it will not be used again within a period of 1 hour.
•Wash and rinse container after each use.
•Clean and sanitize motor base prior to initial use and after each use.
•Washing solutions based on non-sudsing detergents and chlorine-based
sanitizing solutions having a minimum chlorine concentration of 100 PPM
are recommended.
The following washing, rinsing, and sanitizing solutions, or their equivalents,
may be used.
•In repetitive batch-processing applications, frequent cleaning of the
container will prolong the life of the blade assembly. In no case should
actual running time between cleanings exceed ½ hour.
•Do not use container to store processed foods or beverages.
SOLUTION PRODUCT DILUTION IN WATER TEMPERATURE
Washing International Products
Corporation LF2100 Liquid
Low-Foam Cleaner
1%–2%: 1¼ – 2¾ Ounce/Gallon (lower
dilution of 1% for normal cleaning and
up to 2% for more stubborn soils)
Room
Temperature
Rinsing Plain Water Warm 95˚F (35˚C)
Sanitizing Clorox
®
Regular Bleach
(8.25% Hypochlorite
Concentration)
2 Teaspoons/Gallon (Alternately a bleach
with 5.25% Hypochlorite Concentration
can be used at dilution of 3 Teaspoons/
Gallon)

12
TO WASH AND RINSE CONTAINER:
1. REMOVE CONTAINER FROM MOTOR BASE. Remove lid. Rinse
container interior and lid under running water. Add washing solution to
container. Scrub and flush out the container interior and lid to dislodge
and remove as much food residue as possible. Empty container.
2. Wipe down exterior of container with a soft cloth or sponge dampened
with washing solution. Wash lid and lid insert in fresh washing solution.
Fill container ¼ full with fresh washing solution, cover (with lid only),
place on motor base and run on the highest speed for two (2) minutes.
Empty container.
3. Repeat step (2) using clean rinse water in place of washing solution.
IMPORTANT
NOTE: IN ORDER TO MINIMIZE POSSIBILITY OF SCALDING, TEMPERATURE
OF WASHING SOLUTION AND RINSE WATER MUST NOT EXCEED 115˚F (46˚C),
AND QUANTITY USED MUST NOT EXCEED ¼ CONTAINER FULL.
TO SANITIZE AND DRY CONTAINER:
1. Wipe down exterior of container with a soft cloth or sponge dampened
with sanitizing solution.
2. Fill container with sanitizing solution, cover, place on motor base, and
run on high speed for two (2) minutes. Empty container. Dislodge any
residual moisture from blade assembly by placing empty container on
motor base and running on the highest speed for two (2) seconds.
3. Sanitize lid and lid insert by immersing in sanitizing solution for two
(2) minutes.
4. Do not rinse container, lid, or lid insert after sanitizing is completed.
Allow parts to air-dry.
TO CLEAN AND SANITIZE MOTOR BASE:
1. UNPLUG POWER CORD. Wipe down exterior surfaces of motor base
with soft cloths or sponges dampened with washing solution, rinse
water, and sanitizing solution. Prevent liquid from running into motor
base by wringing all excess moisture from cloths or sponges before
using them.
DO NOT IMMERSE MOTOR BASE IN WASHING SOLUTION, RINSE
WATER OR SANITIZING SOLUTION.
2. Allow motor base to air-dry before using.
Any other servicing should be performed by an authorized service
representative.

13
MX BLENDER ACCESSORIES GUIDE
MODEL DESCRIPTION
CAC158* Blending Assembly Kit – Includes
Blade and Gasket
CAC186* Removable Drive Coupling for All
Xtreme MX Series Blenders
*Recommended maintenance: To ensure proper performance, replace every 3 to 6 months.
CAC95
The Raptor®64 oz., BPA-Free
Copolyester Container Complete with
Blade and Lid – Xtreme MX Series
CAC93X
The Raptor®48 oz., BPA-Free
Copolyester Container Complete with
Blade and Lid – Xtreme MX Series
CAC116 Blending Assembly Kit and Retainer
Ring Kit for CAC93X & CAC95
CAC119
Retainer Ring Wrench for CAC93X &
CAC95 (to remove blending assembly
from container)
CAC159 Retainer Ring Kit – Includes Retainer
Ring and Gasket
CAC161
Drive Coupling Removal Tool for All
Xtreme MX Series Blenders (to remove
drive coupling from motor base)
CAC162
Drive Coupling & Coupling Removal
Tool for All Xtreme MX Series Blenders
(to remove drive coupling from
motor base)
*Recommended maintenance: To ensure proper performance, replace every 3 to 6 months.

14
AUTHORIZED SERVICE CENTERS
For a zip code search of authorized service centers near you,
visit waringcommercialproducts.com/support.
Or write to:
Waring Factory Service Center
314 Ella T. Grasso Ave.
Torrington, CT 06790
[phone]
Ship blenders for repair to the above address or to an Authorized Service
Center. Do not ship to a Waring Sales Office.
NOTE: If your application involves the processing of biologically active
material, we request that any items returned for service be sterilized
before being shipped. Such items must be clearly identified as having
been sterilized, both by a tag on the item itself and by a statement in the
accompanying correspondence. Waring will not accept delivery of any return
unless it is so identified.
Replacement parts for your out-of-warranty repairs are obtainable at the
address below.
LIMITED THREE-YEAR MOTOR WARRANTY
LIMITED TWO-YEAR WARRANTY
Waring warrants every new Waring®Commercial Blender to be free from
defects in material and workmanship for a period of two years from the
date of purchase when used with foodstuffs, nonabrasive liquids (other than
detergents) and nonabrasive semi-liquids, providing it has not been subject to
loads in excess of the indicated rating. In addition, the motor in this appliance
has a full three-year warranty.
Under this warranty, Waring, during the warranty period, will repair or replace
any part which, upon our examination, is defective in materials or workmanship,
provided the product is delivered prepaid to the Waring Service Center at: 314
Ella T. Grasso Ave. Torrington, CT 06790, or any Factory Approved Service
Center.
Thiswarrantydoesnot:a)applytoanyproductwhichhasbecomeworn,defective,
damaged or broken due to misuse or due to repairs or servicing by other than the
Waring Service Center or a Factory Approved Service Center, or due to abuse,
misuse, overloading or tampering; or b) cover incidental or consequential
damages of any kind.
The two-year warranty is applicable only to appliances used in the United States
or Canada; this supersedes all other express product warranty or warranty
statements. For Waring products sold outside of the U.S. and Canada, the
warranty is the responsibility of the local importer or distributor. This warranty
may vary according to local regulations.
Warning: This warranty is void if appliance is used on Direct Current (D.C.)
WARING COMMERCIAL
314 Ella T. Grasso Ave.
Torrington, CT 06790

15

1616
MEDIDAS DE SEGURIDAD
IMPORTANTES
Al usar aparatos eléctricos, siempre debe tomar precauciones básicas
de seguridad, entre ellas las siguientes:
1. LEA TODAS LAS INSTRUCCIONES.
2. Siempre desenchufe el aparato cuando no esté en uso, antes de
moverlo, antes de instalar/sacar piezas y antes de limpiarlo.
3. Para evitar los riesgos eléctricos, no sumerja el aparato en agua ni en
ningún otro líquido.
4. Los niños o las personas que carezcan de la experiencia o de los
conocimientos necesarios para manipular el aparato, o aquellas cuyas
capacidades físicas, sensoriales o mentales estén limitadas, no deben
usar este aparato. No permita que los niños jueguen con este aparato.
5. Evite el contacto con las piezas móviles.
6. No use este aparato si el cable o el enchufe están dañados, si no
funciona correctamente, si está dañado, o después de que se haya
caído, incluso en el agua;
devuélvalo a un centro de servicio autorizado para su revisión,
reparación o ajuste.
7. El uso de accesorios/aditamentos no recomendados por el fabricante,
incluso frascos para conservas, presenta un peligro.
8. No lo use en exteriores.
9. No permita que el cable cuelgue del borde de la encimera o de la mesa,
ni que tenga contacto con superficies calientes.
10. Para reducir el riesgo de heridas graves o de daño al aparato, mantenga
las manos y los utensilios fuera de la jarra durante el funcionamiento.
Se puede usar una espátula de goma, siempre que el aparato esté
apagado.
11. Las cuchillas son muy afiladas; manipúlelas con cuidado.
12. No encienda el aparato a menos que la tapa esté puesta.
13. Para licuar líquidos calientes, quite el tapón medidor (la parte central de
la tapa). Consulte la sección “LÍQUIDOS CALIENTES”.
14. Se recomienda usar equipo de protección auditiva al usar el aparato por
períodos largos.
15. Antes del primer uso: Limpie la licuadora y la jarra según se describe en
la sección “LIMPIEZA Y DESINFECCIÓN”.
16. Coloque el aparato de tal manera que el enchufe esté accesible.
17. NO procese líquidos carbonatados con este aparato ni con ninguna otra
licuadora; esto puede causar heridas.
18. NO licue aceite o mezclas a base de aceite (p. ej., mantequilla de maní)
por más de 5 minutos.
19. Espere hasta que el motor se haya detenido por completo y que las
cuchillas estén inmóviles antes de retirar la jarra de la base.
GUARDE ESTAS INSTRUCCIONES

17
MODELOS CON CONTROLES MECÁNICOS
1. Compruebe que el aparato está apagado y
desenchufado, y que la jarra no está en la base.
2. Ponga los ingredientes en la jarra y cierra la tapa.
No llene la jarra más allá de la línea de llenado
máximo “MAX”.
3. Coloque la jarra sobre la base, tras haber
comprobado que el interruptor está en la posición
STANDBY/ . Compruebe que la jarra está
completamente asentada en la base y que el sistema de acoplamiento
está correctamente engranado. Enchufe el cable en una toma de
corriente.
4. Este aparato cuenta con dos velocidades: alta (HI/ ) y baja (LO/ ).
Ponga el interruptor en la posición deseada para encender el aparato.
Nota: Use la velocidad alta (HI/ ) para picar hielo.
5. Para apagar el aparato, ponga el interruptor en la posición STANDBY/ .
6. Este modelo cuenta con una función de pulso (PULSE/ ). Para usar
esa función, accione el interruptor PULSE/ hacia abajo. El aparato
funcionará a velocidad alta hasta que suelte el interruptor.
7. Permita que el motor se detenga completamente antes de retirar la
jarra de la base. Nunca instale/retire la jarra mientras el motor está
encendido.
8. Siempre sostenga la jarra con una mano durante el funcionamiento.
Nunca haga funcionar la licuadora sin la tapa puesta.
9. Lave y seque la jarra después de cada uso (véase las instrucciones de
limpieza y desinfección).
MODELOS CON CONTROLES ELECTRÓNICOS
(SIN RECINTO DE INSONORIZACIÓN)
1. Compruebe que el aparato está apagado y
desenchufado, y que la jarra no está en la base.
2. Ponga los ingredientes en la jarra y cierra la tapa.
No llene la jarra más allá de la línea de llenado
máximo “MAX”.
3. Coloque la jarra sobre la base. Compruebe que la jarra está
completamente asentada en la base y de que el sistema de
acoplamiento está correctamente engranado. Enchufe el cable en una
toma de corriente.
4. Este modelo cuenta con un panel de control táctil electrónico que
incluye los botones siguientes: STANDBY/ (alimentación), HI/
(velocidad alta), LO/ (velocidad baja), STOP/ (pausa) y PULSE/
(pulso).
5. Presione el botón STANDBY/ para alimentar el aparato; el indicador
luminoso verde se encenderá. Para encender el motor, presione el botón
de velocidad deseado, LO/ o HI/ . Para apagar el aparato, presione
el botón STOP/ . Para usar la función de pulso, presione el botón

18
PULSE/ ; el motor funcionará a velocidad alta (HI/ ) hasta que
suelte el botón.
NOTA: Este aparato cuenta con una función de arranque lento Slow
Start™. Después de presionar el botón HI/ , la unidad se pondrá en
marcha a velocidad baja por 2 segundos, y luego pasará a la velocidad
alta. Esto permite obtener resultados más homogéneos.
6. Permita que el motor se detenga completamente antes de retirar la
jarra de la base. Nunca instale/saque la jarra mientras el motor está
encendido.
7. Siempre sostenga la jarra con una mano durante el funcionamiento.
Nunca haga funcionar la licuadora sin la tapa puesta.
8. Lave y seque la jarra después de cada uso (véase la sección
“INSTRUCCIONES DE LIMPIEZA Y DESINFECCIÓN”).
9. Para apagar el aparato, presione el botón STANDBY/ ; la luz verde se
apagará.
MODELOS CON CONTROLES ELECTRÓNICOS Y TEMPORIZADOR
1. Compruebe que el aparato está apagado y
desenchufado, y que la jarra no está en la base.
2. Ponga los ingredientes en la jarra y cierra la tapa.
No llene la jarra más allá de la línea de llenado
máximo “MAX”.
3. Coloque la jarra sobre la base. Compruebe que la
jarra está completamente asentada en la base y que
el sistema de acoplamiento está correctamente engranado. Enchufe
el cable en una toma de corriente.
4. Este modelo cuenta con un panel de control táctil electrónico que
incluye los botones siguientes: STANDBY/ (alimentación), HI/
(velocidad alta), LO/ (velocidad baja), STOP/ (pausa) y PULSE/
(pulso), así como un temporizador de cuenta regresiva de 30 segundos
con una flecha y una flecha para fijar el tiempo.
5. Presione el botón STANDBY/ para alimentar el aparato; el indicador
luminoso verde se encenderá. La pantalla digital mostrará 10
segundos (el tiempo por defecto). Para fijar el temporizador, presione
repetidamente el botón de flecha deseado, o ; el temporizador
electrónico indicará el tiempo, en incrementos de 1 segundo, hasta un
máximo de 30 segundos. Después de fijar el temporizador, presione el
botón HI/ o LO/ para encender el aparato El temporizador de
cuenta regresiva se apagará al final del tiempo prefijado. Para apagar
el aparato, incluso antes del tiempo prefijado, presione el botón
PULSE/ , STOP/ o STANDBY/ .
NOTA: Para reducir o incrementar el tiempo durante el funcionamiento,
simplemente presione el botón de flecha deseado, o ; el tiempo
subirá o bajará en incrementos de 5 segundos.
6. Si no enciende el aparato dentro de 5 segundos, el temporizador se
reinicializará. Para reactivar el temporizador, presione el botón de flecha

19
deseado, o ; el temporizador se pondrá en marcha otra vez,
desde el principio del tiempo prefijado. Nota: Si desenchufa el aparato,
el temporizador volverá al tiempo por defecto: 10 segundos.
7. Para encender el motor, presione el botón de velocidad deseado, LO/
o HI/ . Para apagar el aparato, presione el botón STOP/ . Para usar la
función de pulso, presione el botón PULSE/ ; el aparato funcionará a
velocidad alta hasta que suelte el botón.
NOTA: Este aparato cuenta con una función de arranque lento Slow
Start™. Después de presionar el botón HI/ , la unidad se pondrá en
marcha a velocidad baja por 2 segundos, y luego pasará a la velocidad
alta. Esto que permite obtener resultados más homogéneos.
8. Permita que el motor se detenga completamente antes de retirar la
jarra de la base. Nunca instale/saque la jarra mientras el motor está
encendido.
9. Lave y seque la jarra después de cada uso (véase las instrucciones
de limpieza y desinfección).
10. Para apagar el aparato, presione el botón STANDBY/ ; la luz verde
se apagará. MODELOS CON VELOCIDAD VARIABLE
Advertencia – Este aparato es un producto de Clase A. En un entorno
doméstico, puede causar interferencias radioeléctricas que obliguen al
usuario a tomar las medidas adecuadas.
1. Cerciórese de que el aparato está apagado y
desenchufado, y que la jarra no está en la base.
2. Ponga los ingredientes en la jarra y cierra la
tapa. No llene la jarra más allá de la línea de
llenado máximo “MAX”.
3. Coloque la jarra sobre la base, tras haber comprobado que el
interruptor está en la posición STANDBY/ . Compruebe que la
jarra está completamente asentada en la base y que el sistema de
acoplamiento está correctamente engranado. Enchufe el cable en una
toma de corriente.
4. Este modelo cuenta con velocidad variable. Elija la velocidad deseada,
desde 1 hasta 10.
5. Deje el interruptor izquierdo en la posición “VARIABLE”. Ponga el
interruptor de encendido/apagado en la posición “ON”.
6. Para apagar el aparato, ponga el interruptor en la posición
STANDBY/ .
7. Este modelo cuenta con una función de pulso (PULSE). Si mantiene el
interruptor izquierdo hacia abajo, se activará la función de PULSO CON
VELOCIDAD VARIABLE (la velocidad de pulso se controla con la perilla).
Si coloca el interruptor ON/STANDBY en la posición “ON” y activa
el interruptor PULSE, la función de pulso funcionará a la velocidad
máxima (30.000 RPM). Si suelta el interruptor PULSE, la velocidad
volverá al modo de velocidad variable.

20
8. Permita que el motor se detenga completamente antes de retirar la
jarra de la base. Nunca instale/retire la jarra mientras el motor está
encendido.
9. Siempre sostenga la jarra con una mano durante el funcionamiento.
Nunca haga funcionar la licuadora sin la tapa puesta.
10. Lave y seque la jarra después de cada uso (véase las instrucciones
de limpieza y desinfección).
MODELOS CON FUNCIONES REPROGRAMABLES
1. Compruebe que el aparato está apagado y desenchufado, de que la
jarra no está en la base.
2. Ponga los ingredientes en la jarra y cierra la tapa. No llene la jarra más
allá de la línea de llenado máximo “MAX”.
3. Coloque la jarra sobre la base. Compruebe que la jarra está
completamente asentada en la base y que el sistema de acoplamiento
está correctamente engranado. Enchufe el cable en una toma
de corriente.
4. Use los botones o para ajustar la
velocidad. La velocidad del motor varía entre
el 5 % y el 100%.
100% 20.000 RPM
50% 10.000 RPM
5% 1000 RPM
El botón aumenta la velocidad en incrementos de 1%. El botón
reduce la velocidad en incrementos de 1%. Para desplazarse
por las opciones de velocidad más rápidamente, mantenga el botón
presionado.
Elija la velocidad deseada, presionando el botón o . Si no elije
ninguna velocidad, la opción por defecto es 100%.
NOTA: El aparato no se pondrá en marcha hasta que presione el botón
START/STOP . Si no presiona el botón START/STOP dentro de 5
segundos, el aparato volverá al modo de espera (STANDBY), después
de guardar en la memoria la velocidad programada. El mensaje “PRESS
ANY BUTTON TO BLEND” (presione cualquier botón para licuar)
aparecerá otra vez en la pantalla.
5. Presione el botón START/STOP para encender el aparato; el
aparato funcionará de manera continua, a la velocidad programada.
La velocidad del motor aparecerá en la pantalla (en porcentaje). 100%
es la velocidad por defecto. Para cambiar la velocidad durante el
funcionamiento, simplemente presione el botón o .
6. Para apagar el aparato, presione el botón START/STOP o una de
las funciones preprogramadas.