Watchguard SSL 560 User manual

WatchGuard® Technologies, Inc.
WatchGuard® SSL 560
Quick Start Guide

Register with LiveSecurity® Service
• Find the serial number on your device and record it.
• Go to http://www.watchguard.com/activate
• Log in.
NOTE: If you are new to WatchGuard, follow the instructions to create a prole.
• Follow the instructions on the screen.
• It is a good idea to download and extract your WatchGuard SSL
feature key during activation. Extract the feature key on to the computer you will use
to congure your WatchGuard SSL 560.
Connect your WatchGuard SSL 560
• Make sure your computer is congured with a static IP address on the
192.168.111.0/24 network.
NOTE: The default IP address on the WatchGuard SSL 560 is 192.168.111.1.
• Connect the Ethernet interface on your computer to the interface (Eth1) on your
WatchGuard SSL device.
Getting Started
1
2
3
• Power on the WatchGuard SSL 560.
Run the Quick Setup Wizard
• Open a web browser and type: https://192.168.111.1:8443. Follow the directions in the
wizard to set up your WatchGuard SSL device.
NOTE: Because the WatchGuard SSL 560 uses a self-signed certicate, you may see a certicate warning in
your browser. It is safe to ignore the warning (Internet Explorer) or to add a certicate exception (Mozilla
Firefox).
• In the wizard, you must decide on the conguration mode that best suits your
network. These diagrams show the two conguration modes. For more information on
how to deploy the SSL device, see the online help.
Single
Interface
Mode
Dual
Interface
Mode
Firewall
DMZ 1
DMZ 2
Eth 0
Eth 1
switchswitch
Trusted Resources
WatchGuard SSL 560
Firewall
DMZ 1
Eth 0
switch
WatchGuard SSL 560
Trusted Resources
Eth 1

Congratulations! You have nished basic network setup of your WatchGuard SSL 560.
You can now put the WatchGuard SSL 560 in your network and use the WatchGuard SSL
Web UI to continue conguration, management, and monitoring tasks.
Next Steps
If you did not upload your feature key in the wizard, you can get your feature key at
https://www.watchguard.com/archive/getcredentials.asp. From the Web UI, go to Monitor
System > Feature Key to upload it.
Download and Install Latest Software
• Go to www.watchguard.com/archive/softwarecenter.asp
• Find and download the latest version of WG SSL OS.
• From the Web UI, go to Manage System > Device Update.
For more information about how to congure your WatchGuard SSL 560, go to
www.watchguard.com/help/documentation and open the current help system.
If you congured your WatchGuard
SSL in Single Interface mode…
• When you put the WatchGuard SSL
in your network, make sure you
connect to Eth0. Eth1 is available
only during the Quick Setup
Wizard.
• Reset the IP address on your
computer.
• To connect to the WatchGuard
SSL Web UI, open a web browser
and type: https://[Eth0 IP
address]:8443
If you congured your WatchGuard
SSL in Dual Interface mode…
• When you put the WatchGuard SSL
in your network, make sure you
connect both Eth0 and Eth1.
• Reset the IP address on your
computer.
• To connect to the WatchGuard
SSL Web UI, open a web browser
and type: https://[Eth1 IP
address]:8443
English

ADDRESS: 505 Fifth Avenue South, Suite 500, Seattle, WA 98104
WEB: www.watchguard.com • U.S. SALES: 1.800.734.9905 • INTERNATIONAL SALES: +1.206.613.0895
© 2010 WatchGuard Technologies, Inc. All rights reserved. WatchGuard and the WatchGuard Logo are
either trademarks or registered trademarks of WatchGuard Technologies, Inc. in the United States and/
or other countries. All other trademarks and tradenames are the property of their respective owners.
P.N. 352-3643-001 042210
1.877.232.3531 +1.206.613.0456 www.watchguard.com/support
(U.S. and Canada) (all other countries)
WATCHGUARD TECHNICAL SUPPORT