Watchguard Transfer Station II User manual

Important Notices
Copyright © 2020 WatchGuard, Inc. All rights reserved. This document and supporting data are the
exclusive property of WatchGuard, Inc. and may not be copied and/or reproduced without
permission.
Firmware updates
WatchGuard is committed to the continual testing and improvement of our firmware. As new
revisions become available, these updates will be made available to your agency; fees may apply
depending on your licensing agreement.
Manufacturer contact information
WatchGuard, Inc.
415 E. Exchange, Allen, TX 75002-2616
Customer Service: 1-800-605-6734
Customer Service web portal: https://support.watchguardvideo.com/
Send us your suggestions
We want to hear from you. Tell us about your experience and how you are using the V300. We will
do our best to accommodate any suggestions you may have in future revisions. International
customers, please contact your local distributor.
Trademark notices
Bluetooth® is a registered trademark of Bluetooth SIG, Inc.
Wi-Fi® is a trademark of the non-profit Wi-Fi Alliance
All other marks, names, and logos mentioned herein are the property of their respective owners.
ii Transfer Station II Quick Start Guide WGD00172
Rev B

Transfer Station II Quick Start
Guide WGD00172 Rev B
iii
Contents
Getting Started 5
Setting up Transfer Station II hardware 6
Transfer Station II Configuration Settings 8
Admin Transfer Station II Settings 8
Transfer Station II Configuration 8
V300 Settings 10
DHCP IP Config 10
Upgrade Transfer Station II 11
Administrative functions 11
Change Username and Password 11
Disable Transfer Station II 12
Restart Transfer Station II 12
Get Transfer Station II Logs 12
Transfer Station II LCD Workflow 13
Power LED indicators 13
Activity LED indicators 13
Transfer Station II front LED indicators 13

iv Transfer Station II Quick Start Guide WGD00172
Rev B
This page intentionally left blank.

Getting Started
Getting Started
The Motorola Solutions Transfer Station II is a pass-through USB to Ethernet solution. The Ethernet
throughput rate is 1-10 Gbps. The Transfer Station II supports simultaneous upload from eight V300
Cameras to the cloud. While uploading events, the Transfer Station II can charge up to eight cameras.
When you set up the Transfer Station II, you connect it to power and to the Evidence Library network.
Important! To use the V300 Transfer Station to upload events, your Evidence Library
software must be EvidenceLibrary.com (EL) or Evidence Library on-premise (EL).
When the transfer station is on, the power LED is on.
To use the Transfer Station II:
1. Set up the Transfer Station II hardware.
2. Configure the Transfer Station II so the V300 Cameras docked in it will upload to EL.
Transfer Station II Quick Start Guide WGD00172
Rev B
5

Getting Started
Setting up Transfer Station II hardware
Motorola Solutions provides you a:
lPower cable
lEthernet cable
lStation ID and Slot # stickers
Motorola Solutions offers rack options for mounting multiple transfer stations in the same location.
For information, contact your sales representative.
To set up the Transfer Station II hardware:
1. Use the provided Station ID/Slot # stickers to label the Transfer Station II slots.
Tip: The labels assume an alphabetic Station ID, for example, A, then slot numbers 1
through 8.
Important! Enter the Station ID and Location that you entered when you
configured the Transfer Station II for use with your Evidence Library software. The
Station ID combined with the Location indicates a specific V300 Camera to Evidence
Library.
2. Connect the Ethernet cable to the Ethernet connector on the back of the Transfer Station II.
3. Connect the power cable to the power connector on the bottom of the Transfer Station II and plug
the power cable into an electrical outlet
4. Power the transfer station ON using the switch on the back. The serial number is on the bottom.
5. Connect the other end of the Ethernet cable to a computer that you have set up to access the
Transfer Station II factory default configuration web page.
Tip: Use the Transfer Station II factory default IP address to access the default
6Transfer Station II
Quick Start Guide WGD00172 Rev B

Setting up Transfer Station II hardware
configuration web page: https://192.168.2.20. The computer you use must
have access to this network.
To continue setting up the Transfer Station II, follow the instructions (page 8) to configure the
Transfer Station II to work with your Evidence Library software.
Transfer Station II Quick Start Guide WGD00172
Rev B
7

Getting Started
Transfer Station II Configuration Settings
Configure each Transfer Station II individually using a web page specific to the Transfer Station II.
You configure:
lTransfer Station II Settings
lV300 Camera Settings (page 8)
Important! To use the V300 Transfer Station to upload events, your Evidence Library
software must be EvidenceLibrary.com (EL) or Evidence Library on-premise (EL).
Admin Transfer Station II Settings
1. Connect the Ethernet cable from the Transfer Station II to the computer.
2. Open your web browser and enter https://192.168.2.20, the Transfer Station II default IP address.
3. Log in to your Transfer Station II web page on the Secure Sign In screen.
4. Enter the Username and Password (Admin,V1$T@xfr).
5. Click login.
Transfer Station II Configuration
The Current Transfer Station II Configuration web page opens with the Transfer Station II
default settings.
8Transfer Station II
Quick Start Guide WGD00172 Rev B

Transfer Station II Configuration
1. Assign a Static IP Address or let your DHCP server assign its IP addres
Note: Use a static IP address for easy access to the UI for troubleshooting.
2. Enter the Location of the Transfer Station II.
3. Enter a unique IP address for each Transfer Station II.
4. Enter the Station ID that identifies the current Transfer Station II. Station ID fields each have a 32-
character limit.
In the example, Transfer Station II uses Building 415 as the location and B as the Station ID.
EL uses these names to identify the individual V300 Cameras and location of the cameras.
Note: Motorola Solutions provides labels that assume an alphabetic Station ID
combined with slot numbers 1 through 8.
5. Enter your IP Config type, either Static or DHCP server assigned. For DHCP setup, see (page 10).
The first screen shows a Static configuration.
Note: Motorola Solutions recommends that you set up a pool of static IP addresses
that you assign to your Transfer Station II.
6. Complete the remainder of the settings.
7. Click Save Settings.
Because the Transfer Station II IP address changed, the default configuration web page is no longer
valid and the system logs you out.
Transfer Station II Quick Start Guide WGD00172
Rev B
9

Getting Started
V300 Settings
1. Complete the V300 Settings.
2. Enter your Static IP addresses for each slot.
This window does not appear if you choose DHCP server assigned address.
3. Click Save V300 Settings.
DHCP IP Config
If you choose to go with DHCP for your IP Config, complete the two screens shown here.
1. Enter the Tenant ID. (Optional. Call Customer Support to get the ID.)
Note 1: You can get the Tenant ID when doing the initial setup of your system with technical
support.
10 Transfer Station II
Quick Start Guide WGD00172 Rev B