Water Right Impression Owner's manual

Master Programming Manual
for Impression, Impression Plus,
and Impression Twin Models
Effective January 2018

2
Button appearance and position may be different than actual valve
Cycle times, sequences, and settings in this guide are only examples of how your system may be programmed.
Actual settings are determined by the manufacturer. Please contact them if more information is needed.
Important button sequences to note:
1. UNLOCK VALVE SETTINGS: Push buttons in the following order: –, NEXT, +, CLOCK. This will allow user to change
manufacturer’s settings. When finished, lock settings by pushing the same sequence.
2. CLEAR ERROR ON SCREEN: Push and hold NEXT and REGEN for three seconds.
3. CLEAR SERVICE ALARM: If service alarm is triggered, push and hold +and –simultaneously for three seconds to reset to
original set points. This will reset both gallon and year alarms.
General Operation Screens
Set Time Screens Typical Regen Screens
Pressing NEXT will toggle between one of five displays. Press REGEN to set a regeneration to occur tonight.
Accessed by pressing CLOCK. Only visible when unit is in regeneration.
DAYS TO A REGEN
GPM
3
8
CAPACITY REMAINING
GPM GAL
1600
8
FLOW RATE
GPM
8.0
TIME OF DAY MON
GPM
2:408
PM
“GPM” and flow rate
flash while turbine is
rotating
Return to general display
Return to general display
“REGEN TODAY”
will alternate with the
current screen header
if a regen is expected
tonight
Displays current time.
Unit defaults to this screen
after a reset.
Displays a unit’s remaining capacity.
This screen will not display if the unit’s gallons of
capacity is set to OFF. The unit may run into negative
capacities and will regenerate two nights in a row if
it overruns its capacity by the selected percentage.
Displays days remaining until a regen.
This screen will not display if the unit’s day
override is set to off.
Set hours with + or — buttons.
AM/PM toggles after 12 AM. Displays time remaining in
current regeneration cycle
“2” flashes for a second backwash if
two backwashes are programmed.
Displays time remaining in
current cycle
If an ozone generator is connected and set to ON,
the duration of the ozone generation is displayed.
Set minutes with + or — buttons.
AM/PM toggles after 12 AM.
Set current day with + or — buttons.
The default setting is WED.
Displays scrolling dealer name
and phone number.
To change dealer name and phone
number, see page 3 or 4.
Displays current flow rate.
“Current Flow Rate” is the amount of
water currently flowing through, and
being treated by, the unit.
555 5555555
DEALER NA
Any one of these chosen
displays will flash alternately
with dealer name screen if set.
CURRENT DAY
SET
WED
TIME MINUTES
SET
TIME HOUR
SET
2:00
2:35
AM
AM MIN
BACKWASH REMAINING
2
3:30
GENERATOR ON
53:45

3
REGEN TIME MINUTES
SET
2:00
AM
REGEN TIME HOUR
SET
2:00
AM
WATER HARDNESS
SET
20
WATER HARDNESS
SET
20
GR
GR
555-555-5555
555-555-5555
LIGHT NORMALLY
SET
ON
DEALER NA
1
3
DAYS BETWEEN REGEN
SET
6
2
4
5
Softener Installer/User Screens
Accessed by pressing and holding NEXT and +simultaneously for three seconds.
Returns to general display after five minutes of inactivity.
Set water hardness with + or — buttons.
Adjustable from 1-150 grains, within limits determined by capacity settings
as to not override gallons capacity setting. Default setting is 20 grains.
NOTE: This screen will not display if the unit is set to “FILTERING” mode (see OEM FILTERING SECTION).
Set days between a regeneration with + or — buttons.
Adjustable from 1-28 days, or OFF.
Default setting is 6.
Set hour of regen time with + or — buttons.
If IMMEDIATE REGEN is set (see Service OEM page), regen will be
immediate once total capacity is exhausted and ON ZERO will be
displayed.
Default setting is 2:00 AM.
Set minutes of regen time with + or — buttons.
If IMMEDIATE REGEN is set (see Service OEM page), regen will be
immediate once total capacity is exhausted and ON ZERO will be
displayed.
Default setting is 2:00 AM.
Set backlight operation with + or — buttons.
Default setting is ON.
OFF will turn display backlight off after 5 minutes of keypad inactivity.
Scrolling contact phone number screen.
Set phone number by using the + or — buttons. Pushing the NEXT
button will advance the cursor one position to the right. Continuing
to press the NEXT button will advance to the Contact Name Display.
Scrolling contact name screen.
Set contact name by using the + or — buttons. Pushing the NEXT
button will advance the cursor one position to the right.
(55 Characters Max)
Access Dealer Name and Phone Number Feature
From the Water Hardness display, the dealer name and phone number feature can be
accessed by pressing the CLOCK and + buttons at the same time.
Return to general display
Only appears on
units that support a
backlit display
Return to general display
To continue programming Installer
Settings, press NEXT and + again
after returning to general display
To Turn Off Dealer
Name/Number Screen
1. Clear the current phone number by pressing
the + or – buttons to toggle to the “blank”
character followed by the NEXT button.
2. Input two “blank” characters. The phone
number should clear and advance to the
dealer name setting.
3. Clear the current dealer name by pressing
the + or – buttons to toggle to the “blank”
character. Input two blank characters. Press
the NEXT button repeatedly until the general
display appears.

4
REGEN TIME MINUTES
SET
12:00
AM
REGEN TIME HOUR
SET
12:00
AM
DAYS BETWEEN REGEN
SET
3
DAYS BETWEEN REGEN
SET
3
555-555-5555
555-555-5555
LIGHT NORMALLY
SET
ON
DEALER NA
1
2
3
4
Filter Installer/User Screens
Accessed by pressing and holding NEXT and +simultaneously for three seconds.
Returns to general display after five minutes of inactivity.
Set hour of regen time with + or — buttons.
If IMMEDIATE REGEN is set (see Service OEM page), regen will be
immediate once total capacity is exhausted and ON ZERO will be
displayed.
Default setting is 12:00 AM.
Set minutes of regen time with + or — buttons.
If IMMEDIATE REGEN is set (see Service OEM page), regen will be
immediate once total capacity is exhausted and ON ZERO will be
displayed.
Default setting is 12:00 AM.
Set backlight operation with + or — buttons.
Default setting is ON.
OFF will turn display backlight off after 5 minutes of keypad inactivity.
Contact phone number screen.
Set phone number by using the + or — buttons. Pushing the NEXT
button will advance the cursor one position to the right. Continuing
to press the NEXT button will advance to the Contact Name Display.
Contact name screen.
Set contact name by using the + or — buttons. Pushing the NEXT
button will advance the cursor one position to the right.
(55 Characters Max)
Access Dealer Name and Phone Number Feature
From the Days Between Regen display, the dealer name and phone number feature can
be accessed by pressing the CLOCK and + buttons at the same time.
Return to general display
Only appears on
units that support a
backlit display
Set days between a regeneration with + or — buttons.
Adjustable from 1-28 days, or OFF.
Default setting is 3.
Return to general display
To continue programming Installer
Settings, press NEXT and + again
after returning to general display To Turn Off Dealer
Name/Number Screen
1. Clear the current phone number by pressing
the + or – buttons to toggle to the “blank”
character followed by the NEXT button.
2. Input two “blank” characters. The phone
number should clear and advance to the
dealer name setting.
3. Clear the current dealer name by pressing
the + or – buttons to toggle to the “blank”
character. Input two blank characters. Press
the NEXT button repeatedly until the general
display appears.

5
FILL
SET
CYCLE 1
DBL REGEN
SET
10 %
>
GALLON CAPACITY
SET
AUTO
SOFTENING
SET
CYCLE 2
CYCLE 3
SOFTENING TIME
SET
240:00
MIN
12:00
MIN
BACKWASH
SET
BACKWASH TIME
SET
FILL
SET
15.0 LBS
X1K
GRAINS OF CAPACITY
SET
32.0
SOFTENING
SET
TYPE
1
2
3
4
5
6
7
8
9
10
Service/OEM SOFTENING Screens
Accessed by pressing and holding NEXT and —simultaneously for three seconds.
Returns to general display after five minutes of inactivity.
Select SOFTENING or FILTERING with + or — buttons.
If you have selected FILTERING, please refer to
“Service/OEM FILTERING screens”, page 7-8.
Set system’s grains of capacity with + or — buttons.
X1K = 1,000 grains.
The default setting is 32.0
Set gallon capacity with + or — buttons.
• AUTO automatically calculates gallon capacity.
• OFF will regen by days override setting only.
• GALS BETWEEN REGEN will regen by specific gallon setting.
• Default setting is AUTO.
Set double regen point with + or — buttons.
If unit’s capacity is overrun by this percentage, the unit will regen
two nights in a row. Default setting is 10%.
Set softening time with + or — buttons.
This is the time between brine tank fill and start of backwash. This
time window allows the salt to dissolve and achieve proper brine
strength. This process will start prior to regen time setting.
Default setting is 240:00 minutes.
Set salt pounds per regen with + or — buttons.
Default setting is 15.0 pounds.
Set backwash time with + or — buttons.
Default setting is 12:00 minutes.
Set second cycle position with + or — buttons.
Set third cycle position with + or — buttons.
Set first cycle position with + or — buttons.
continue to next page
During FILL and
SOFTENING positions,
unit will deliver
soft water.

6
cont’d
CYCLE 4
REGENERANT DRAW DN
SET
90:00
MIN
DRAW TIME
SET
CYCLE 5
RINSE
SET
4:00
MIN
RINSE TIME
SET
CYCLE 6
END
SET
11
12
13
14
15
Service/OEM SOFTENING Screens
Accessed by pressing and holding NEXT and —simultaneously for three seconds.
Returns to general display after five minutes of inactivity.
Set fourth cycle position with + or — buttons.
Set draw time with + or — buttons.
Default setting is 90:00 minutes.
Set fifth cycle position with + or — buttons.
Set final rapid rinse time with + or — buttons.
Default setting is 4:00 minutes
Set end cycle with + or — buttons.
Up to fourteen cycle positions may be programmed into
a regeneration. An END position triggers the end of a
regeneration and a return to service.
continued from previous page
Return to general display

7
DBL REGEN
SET
>10%
CYCLE 1
20
SEC
BACKWASH-AIR
SET
BACKWASH-AIR TIME
SET
GAL
GALLONS CAPACITY
SET
1000
FILTERING
SET
TYPE
CYCLE 2
BACKWASH
SET
CYCLE 3
REGENERANT DRAW DN
SET
10:00
MIN
BACKWASH TIME
SET
1
2
3
4
5
6
7
8
Service/OEM FILTERING Screens
Accessed by pressing and holding NEXT and —simultaneously for three seconds.
Returns to general display after five minutes of inactivity.
NOTE: Numbers and cycles used as examples on this page are typical of AIR FILTER systems.
Select SOFTENING or FILTERING with + or — buttons.
If you have selected SOFTENING, please refer to
“Service/OEM SOFTENING screens”, page 5-6.
Set gallons of capacity with + or — buttons.
To turn off, set below 0. OFF does not use metered water to
determine a regen and will not be an option of days override
is not set. Default setting is 1000 gallons.
Set double regen point with + or — buttons.
If unit’s capacity is overrun by this percentage, the unit will
regen two nights in a row. Default setting is OFF.
Set first cycle position with + or — buttons.
Set backwash-air position time with + or — buttons.
Default setting is 20 seconds.
Set backwash time with + or — buttons.
Default setting is 10:00 minutes.
Set second cycle position with + or — buttons.
Set third cycle position with + or — buttons.
continue to next page

8
cont’d
ON
OZONE GENERATOR
30:00
MIN
GENERATE OZONE
SET
SET
OFF
GENERATOR ALARM
SET
CYCLE 4
END
SET
60:00
MIN
DRAW TIME
SET
60:00
MIN
DRAW TIME
SET
9
10
Set draw time with + or — buttons.
Default setting is 60:00 minutes.
Select option with + or — buttons.
ON: Ozone generator option installed.
OFF: No options installed (default setting).
Set the ozone generator’s operation time with
+ or — buttons.
Default setting is 30:00 minutes.
Select option with + or — buttons.
ON: Will display SERVICE OZONE on user screen when
failure is detected.
Off: No alarm will display.
Set end cycle with + or — buttons.
Up to fourteen cycle positions can be programmed into a regeneration.
An END position triggers the end of a regeneration and a return to service
Press and hold CLOCK and + buttons simultaneously for
three seconds to access OZONE GENERATOR settings.
Service/OEM FILTERING Screens
Accessed by pressing and holding NEXT and —simultaneously for three seconds.
Returns to general display after five minutes of inactivity.
NOTE: Numbers and cycles used as examples on this page are typical of AIR FILTER systems.
continued from previous page
Return to general display
To set OZONE GENERATOR
NOTE: Ozone Generator options are only available if an ozone generator is connected to the
board. Ozone generators are not compatible with all boards and programming. Consult the Ozone
Generator Kit Instructions (OZ1-A-WR) for more information.

9
MAV DRIVE 1
SET
IN
DELAYED
SET
REGEN
OFF
VALVE TYPE
SET
1.0
AUXILIARY INPUT
SET
OFF
1
MIN
Pre-Service Rinse
SET
OFF
2
3
4
Configuration Screens
Accessed by pressing and holding NEXT and —simultaneously for three seconds.
Once screen changes, press and hold NEXT and — simultaneously again for three seconds.
Select meter size with + or — buttons.
Set to 1”, 1.25”, 1.5”, 2” or 1.0T (for twin units). Upflow brining will not be an option if set to anything other than 1” or 1.0T.
With 1.0T set:
• Meter calibration will be fixed.
• MAV 1 setting will not be viewed, but forced to be set to Alternator Mode w/ Immediate Regen and Post Fill Brining.
• The Backwash-Air regeneration step will not be available.
• Default setting is 1”
Set auxilliary input with + or — buttons.
• IMMED indicates unit will regen immediately.
• DELAY indicates that after a 2 minute signal from external contact, unit will regen at delayed regen time.
• HOLD indicates that unit will not regen while external contacts are closed.
• ALARM indicates that control valve’s internal alarm will sound upon external contact closure.
• Default setting is OFF.
WARNING: External contact is needed to operate any of the above settings properly. If no external contact is
connected, no setting is needed.
Set regen time control with + or — buttons.
• DELAYED sets regen to specified regen time.
• DELAY + IMMEDIATE sets regen to occur after 10 minutes of no water usage.
• IMMEDIATE sets an immediate regen upon zero gallons of remaining capacity.
• Default setting is DELAYED.
Set pre-service rinse time with + or — buttons.
This option is only available if the valve type is set to 1.0T (twin).
Range is 0-20 minutes. Default setting is OFF.
Set first MAV drive control with + or — buttons.
• ALT A and ALT B are only used in twin configurations (see MAV manual for more details).
• SYSTEM CONTROLLER configures board to operate with the Clack System Controller.
• SEPARATE SOURCE changes state at the start and end of regen cycle.
• NO HARD BYPASS configures MAV as a no hard water bypass.
• TIME changes state at a set time referenced to the start of regen, for a preset duration of time independent
of actual regen status. Inactive during alternate regeneration cycle.
• Default setting is OFF.
WARNING: Leaving valve in ALT A, ALT B or ENABLED without proper hardware will result in errors.
continue to next page
Only appears
on units set to
1.0T Mode

10
cont’d
RELAY 1 TRIGGER
SET
OFF
RELAY 1 TRIGGER
SET
TIME
RELAY 1 SETPOINT
SET
15
MIN
RELAY 1 DURATION
SET
90:00
MIN
RELAY 1 TRIGGER
SET
GALLONS
RELAY 1 SETPOINT
SET
25
GAL
RELAY 1 DURATION
SET
0:30
MIN
5
Configuration Screens
Accessed by pressing and holding NEXT and —simultaneously for three seconds.
Once screen changes, press and hold NEXT and — simultaneously again for three seconds.
Set first relay trigger with + button. Press + to reach desired triggering event.
If not using a relay, make sure OFF is selected and press NEXT.
OFF indicates that no external devices are being used.
Default is OFF.
continued from previous page
Return to
General Display
Return to
General Display
Return to
General
Display
Set relay trigger with + or — buttons.
TIME indicates that relay will be energized for a specified
period of time during regen only. To set by this, press NEXT.
Set relay setpoint with + or — buttons.
This is the delay time period after regen starts that relay
will initially energize. 0 indicates an immediate start.
Set relay setpoint with + or — buttons.
This is the gallons that will be expended before relay will
initially energize.
Set relay trigger with + or — buttons.
GALLONS indicates that relay will be energized after a specified number of
gallons are expended in service position only. To set by this, press NEXT.
Set relay duration with + or — buttons.
This is the duration of time, after relay setpoint, that relay
will remain energized.
NOTE: Can be all or any part of total regen time, but will
turn off at end of regen.
Set relay duration with + or — buttons.
This is the duration of time, after relay setpoint,
that relay will remain energized. Adjustable from
1 sec to 500 min.
NOTE: Will shut off if a regen is initiated
If using Relay:
1. Push + to engage
one of the following
Relay Triggers:
• Time
• Gallons
• Regen
• Error
• Flow
• Pulse
2. Press NEXT to
program Setpoints
and Durations
continue to next page

11
cont’d
0:30
MIN
RELAY 1 TRIGGER
SET
REGEN
RELAY 1 TRIGGER
SET
ERROR
RELAY 1 SETPOINT
SET
25
GAL
RELAY 1 DURATION
SET
RELAY 1 SETPOINT
SET
1.00
PPG
RELAY 1 TRIGGER
SET
PULSE
RELAY 1 TRIGGER
SET
FLOW
Configuration Screens
Accessed by pressing and holding NEXT and —simultaneously for three seconds.
Once screen changes, press and hold NEXT and — simultaneously again for three seconds.
continued from previous page
Set relay trigger with + or — buttons.
REGEN GALLONS indicates that relay will be energized after a specified number of
gallons are expended during service and regen. To set by this, press NEXT.
Set relay trigger with + or — buttons.
ERROR indicates that relay will be energized while unit is in an error mode. To set by
this, press NEXT.
Set relay trigger with + or — buttons.
FLOW indicates that relay will close whenever flow is detected by the control. To set
by this, press NEXT.
Set relay trigger with + or — buttons.
PULSE indicates that relay will generate a dry-contact signal output. To set by this,
press NEXT.
Set relay setpoint with + or — buttons.
This is the gallons that will be expended before relay will
initially energize.
Set relay setpoint with + or — buttons.
Set meter pulses per gallon (PPG). Adjustable
from 0.10, 0.25, 0.50, 0.75, and 1.00 – 10.00
in 1 PPG increments.
Set relay duration with + or — buttons.
This is the duration of time, after relay setpoint, that relay
will remain energized. Adjustable from 1 sec to 500 min.
Return to
General Display
Return to
General Display
Return to
General Display
Return to general display

12
First Level History Screens
Accessed by pressing and holding +and —simultaneously for three seconds.
Returns to general display after five minutes of inactivity.
DAYS SINCE REGEN
5
VOLUME SINCE REGEN
980
RESERVE FOR
MON GAL
GAL
320
GAL
230
USAGE WED R
DAY
15
A→BGAL
0.00
1 3 DAYS 12:35
1
2
3
4
Displays number of days since last regen.
Displays number of gallons since last regen.
Displays reserve capacity.
Use + or — buttons to scroll through each day of the week to
view calculated reserve capacity.
NOTE: Reserve capacity takes 21 days to generate.
Only appears
on units set to
1.0T Mode
Displays tank transfer history.
Use + or — buttons to scroll through last 10 tank transfers. Viewed in 1.0T Mode only.
• “1” indicates most recent tank transfer.
• “A” indicates service flow transferring away from tank.
• “B” indicates service flow transferring to tank.
• “3” indicates days ago of transfer (99 day max)
• “0.00” indicates gallons used at time of transfer.
Displays gallon usage history.
Use + or — buttons to scroll through past 90 days of water usage history.
1.0T Mode: T1 and T2 usage for this day combined in this display
• “R” indicates a regen has occurred that day.
• “S” indicates a step through manual regeneration.
• “M” indicates a manual regeneration.
• “E” indicates a valve error has occurred.
continue to next page

13
cont’d
TOTAL REGENS
190
TOTAL DAYS
970
MON GPM
12
MAX FLOW HISTORY
TOTAL GALLONS
X1K
0
VVVCYC
TTT
MAV 1 - FIRST
CCC
mA VDC
REGEN 1
OZONE
260 12.0
5
6
7
8
First Level History Screens
Accessed by pressing and holding +and —simultaneously for three seconds.
Returns to general display after five minutes of inactivity.
continued from previous page
Displays peak flow rate history.
Use + or — buttons to scroll through last 7 days to view peak
flow rate for that day.
Displays ozone current history.
Use + or — buttons to review ozone generator performance during the past 50 regenerations.
A regen sequence indicator (A) will alternated being viewed with “mA” if the Alternate Regen
Feature was active for this regen. Regens with multiple regenerate draws will only record the
first one in the sequence. Values displayed are determined immediately after a low output current
is detected, or will be the average values measured during generator period of operation.
AAA = Generator current draw in mA
VV.V = Generator voltage in VDC
Viewed only if SERVICE/OEM is set to OZONE ON.
Displays MAV drive time history for an active MAV 1 output..
Use + or — buttons to select a MAV output. Pushing both + and — buttons
will reset this display.
First = Average of the first three drive times measured for that MAV in that direction.
Last = Last drive time measured for that MAV in that direction.
Ave = Current average drive time calculated for that MAV in that direction.
TTT = Relative MAV drive time measured (First/Last/Ave).
CCC = Total number of cycles in/out for that MAV.
VVV = Relative MAV drive voltage measured (First/Last/Ave).
Displays total days unit has been in service.
Displays total regens since startup.
Displays total gallons used by Meter 1
input since last reset.
Push and hold + and — buttons simultaneously for
three seconds to reset this value back to 0 gallons.
Return to general display
Only appears
when OZONE
GENERATOR
is on.
Only appears on
units equipped
with MAV.

14
SOFTWARE VERSION
XXX
xx
TOTAL GALLONS
0
X1K
TOTAL DAYS
970
TOTAL REGENS
190
1
ERROR LOG
101
1 4
52
3
Second Level History Screens
Accessed by pressing +and —simultaneously for three seconds.
Once screen changes, press +and —simultaneously again for three seconds.
Non-resettable history.
Displays software version.
Displays total gallons used
by Meter 1 since startup.
Displays total days unit has
been in service.
Displays total regens since startup.
Displays last ten valve errors that occurred.
Scroll through with + or — buttons.
Return to general display
Error Code Error Code Description
101 UNABLE TO START: Valve not sensing valve movement with motor energized.
102 MOTOR STALLED: Valve unable to find next cycle position (stalled).
103 MOTOR RAN TOO LONG: Valve unable to find next cycle position.
104 VALVE HOMING: Valve unable to find Home position.
106 MAV 1 RAN TOO LONG: MAV 1 motor ran too long. Unable to find proper park position.
107 MAV 1 STALLED: MAV 1 motor ran too short. Unable to find proper park position (stalled).
109 INVALID MOTOR STATE: Control can no longer operate properly due to detection of an invalid motor state.
116 MAV 2 RAN TOO LONG: MAV 2 motor ran too long. Unable to find proper park position.
117 MAV 2 STALLED: MAV 2 motor ran too short (stalled). Unable to find proper park position.
201 INVALID REGEN STEP: Control can no longer operate properly due to detection of an invalid
regeneration cycle step. Internal software issue.
204 LEAK DETECTED
402 POWER DOWN MEMORY: Check sum error for operational data and status section of EEPROM memory
- specific type of memory error.
403 PROGRAM MEMORY: Check sum error for programming section of EEPROM memory
- specific type of memory error.
404 DIAGNOSTIC MEMORY: Check sum error for diagnostic section of EEPROM memory
- specific type of memory error.
405 HISTORY MEMORY: Check sum error for history section of EEPROM memory
- specific type of memory error.
406 CONTACT MEMORY: Check sum error for contact screen section of EEPROM memory
- specific type of memory error.
407 STATUS RAM MEMORY
FAILURE:
Control can no longer operate properly due to corrupted data detected in the Operational Data and Status
Section of RAM memory. Once generated, the Error Mode is not entered nor an error displayed, instead
previously stored data (<6 hours old) is used to maintain control operation.
408 DIAGNOSTIC RAM
MEMORY FAILURE:
Control can no longer operate properly due to corrupted data detected in the Operational Data and Status
Section of RAM memory. Once generated, the Error Mode is not entered nor an error displayed, instead
previously stored data (<6 hours old) is used to maintain control operation.
410 CONFIG DOWNLOAD: Configuration file downloaded to the control was not originally uploaded from
another control with the identical software revision.
Error Codes and Descriptions
REMINDER: Press and hold NEXT and REGEN for three seconds to perform a soft reset and clear an error on screen.

15
Notes

1900 Prospect Court • Appleton, WI 54914
Phone: [phone] • Fax: [phone]
MAN-IMP MASTER Rev A0118