water saver PaperSaver Slimline Programming manual

OVERVIEW
PaperSaver Slimline Bidet ts most standard Two Piece toilets (with separate tank and bowl) and is VERY EASY TO OPERATE.
Sleek and thin design minimally protrudes from the toilet and blends well with most bathroom decors. Connects easily to the
exisng toilet water line with the included t-valve and stainless braided hose. Uses NO ELECTRICITY or BATTERIES, so is TOTALLY
SAFE in any bathroom environment. Single horizontal water control knob is large with bold print and works the same when
turned in either direcon . . . rst to clean the nozzle and then further around to spray. The nozzle spray angle adjusts with a
convenient lever tab near the control knob and is also designed with a unique twist out mount for easy cleaning or replacement.
PREPARATION
QUICK START PaperSaver Slimline Bidet Instrucons
Thank You for choosing Water Saver Products ! ! !
◊◊◊ PSBD-1SC1 Rev A © WSP 2020 ◊◊◊
INSTALLATION (over)
This general instrucon sheet covers the basic installaon procedure for this kit. Depending on your specic bathroom
conguraon, further installaon steps and/or tools may be required. For addional informaon please visit our
website at hps://www.water-saver.org or email your quesons to [e-mail].
BRASS T-VALVE
(Items not to relative scale for clarity)
“Home of the FlushSaver DIY Kits”
STANDARD
TWO PIECE TOILET
(SEPARATE TANK AND BOWL)
BIDET
BATHROOM CONFIGURATIONS VARY WIDELY
ACCESSORIES
(Items not to relative scale for clarity)
COMPONENTS
Before aempng installaon, please read these Quick Start Instrucons in full, familiarize yourself with your specic bathroom
conguraon and gather any required tools and hardware. This kit and these instrucons apply to a typical toilet and water supply
conguraon, but since every bathroom is dierent, some installaons may require addional steps or assistance from a professional
plumber. Ensure that the bidet will t the bowl width and shape of the toilet by posioning it over the toilet seat bolts and adjusng
its rotang mounts accordingly. For most installaons, the only tool required is a standard adjustable wrench, but since toilet
plumbing hardware can vary widely, addional tools, ngs or adapters may be required beyond what is supplied with this kit.
TOILET
WATER LINE
INSTALLATION EXAMPLE
(7/8" M/F + G1/2" M)
WASHER
BRAIDED HOSE
Anyone with basic DIY home plumbing experience can install this simple bidet kit . . . MINIMUM COMMON TOOLS REQUIRED.
STAINLESS STEEL
T-VALVE
BRAIDED HOSE
SPRAY NOZZLES
(2 SETS - REMOVABLE)
T-VALVE NUT
15/16" (23mm)
BIDET NUT
5/8" (16mm)
TOP NUT
1 1/16" (27mm)
30” LENGTH {76cm)

CLEAN & SPRAY VOLUME
INSTALLATION
1
3
NOTE: Turn o the t-valve when not in use for
extended periods as a precauon against leaks ! ! !
OPERATION
Certain water condions with high mineral
content may cause the nozzle orices to
clog over me. Soak in vinegar or descaler
then use a so brush to remove deposits.
The spray nozzle will self clean each me the control
knob is rotated into the CLEAN posion. If a more
thorough cleaning is required, remove the nozzle by
rotang it to the le to unlock it from the mount.
MAINTENANCE
BET
Check nozzle for
proper assembly
of o-ring and lock
collar as shown.
With the nozzle and
nozzle mount arrows
poinng toward each
other, align the nozzle
tabs to the mount, insert
and twist to the right
unl it locks into place.
COLLAR
O-RING
NOZZLE
NOTE SPARE NOZZLE INCLUDED
MOUNT
NOZZLE
2
DO NOT OVERTIGHTEN MOUNT BOLTS
BOLTS
NUT
Remove the toilet seat
bolts and slide the bidet
underneath the seat
mounts while posioning
the bidet mounts to align
with the same bolt holes. SEAT
FLUSH & HOLD
SPIGOT
TOWEL
WATER
Note how the bidet mounts
can be rotated as required to
achieve the proper t. Once
in posion, reinstall the seat
bolts and snug down.
Place a towel under
the toilet tank water
line to catch any water
that drips down during
removal. Turn o the
water spigot, then
ush the toilet and
hold the handle down
to drain out as much
water as possible.
4
T-VALVE
WATER LINE
FILLER VALVE INLET
HAND SNUG ONLY - DO NOT WRENCH TIGHTEN YET
WASHER
Connect the included
braided hose from the
t-valve outlet port to
the bidet inlet port.
Orient the posion of
the t-valve as desired.
5
Carefully ghten
all ngs, but do
not over ghten.
Usually 1/8 to 1/4
turn past hand
snug is enough.
BRAIDED
BIDET
INLET
HOSE
Turn the water spigot and t-valve on SLOWLY to check
for leaks. Then place your right hand in front of the
spray nozzle to catch the spray and rotate the control
knob either way with your le hand. Note how the clean
and spray volume relates to the posion of the knob.
NOZZLE ANGLE
(TURN EITHER DIRECTION)
T-VALVE
OUTLET
Disconnect the toilet water
line at the tank ller valve
inlet. Be prepared for a small
amount of water to run out
from the tank ller valve
upon removal. Connect the
included t-valve and washer
to the ller valve inlet and
reaach the water line to it.