WaterGroup WG185ACF75 User manual

185DFBackwashingFilters
Carbon—TasteandOdor(ACF)
Multimedia(MMF)
NextSand(ULTRAMF)
Neutralizer(NNF)

Owners Manual
REVISION # 0
REVISION DATE Feb 28,2015
54825
FOLLOWTHE INSTALLATION INSTRUCTIONS CAREFULLY. FAILURE TO
INSTALL THE UNIT PROPERLY VOIDS THE WARRANTY. BEFORE YOU
BEGIN INSTALLATION, READ THIS ENTIRE MANUAL. THEN, OBTAIN ALL
THE MATERIALS AND TOOLS
1. Avoid pinched o-rings during installation by applying (provided with install kit) NSF
certified lubricant to all seals.
2. This system is not intended for treating water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the system.

Safety Guide
 Check and comply with your provincial /
state and local codes. You must follow
these guidelines.
 Use care when handling the filter tank. Do
not turn upside down, drop, drag or set on
sharp protrusions.
 The system works on 12 volt-60 Hz electri-
cal power only. Be sure to use only the
included transformer.
 Transformer must be plugged into an in-
door 120 volt, grounded outlet only.
 WARNING: This system is not in-
tended for treating water that is microbio-
logically unsafe or of unknown quality
without adequate disinfection before or
after the system.
For your safety, the information in this manual must be followed to minimize the risk of
electric shock, property damage or personal injury.
Be sure to check the entire unit for any shipping damage or parts loss. Also note damage to
the shipping cartons. Contact the transportation company for all damage and loss claims.
The manufacturer is not responsible for damages in transit.
Small parts, needed to install the softener, are in a parts bag. To avoid loss of the small
parts, keep them in the parts bag until you are ready to use them.
Unpacking / Inspection
PAGE
Unpacking / Inspection 2
Safety Guide 2
Proper Installation 3
Specification 4
Before Starting Installation 5
Sizing Requirements 7
Installation Instructions 8
System Start Up 10
About The System 12
Maintenance 14
Main Repair Parts 16
Trouble Shooting 23
Warranty 24
Table of Contents
2

Proper Installation
This water filter system must be properly installed and located in accordance with the
Installation Instructions before it is used.
 Do not install or store where it will not be
exposed to temperatures below freezing or
exposed to any type of weather. Water
freezing in the system will break it. Do not
attempt to treat water over 100°F.
 Do not install in direct sunlight. Excessive
sun or heat may cause distortion or other
damage to non-metallic parts.
 Properly ground to conform with all gov-
erning codes and ordinances.
 Use only lead-free solder and flux for all
sweat-solder connections, as required by
state and federal codes.
 Maximum allowable inlet water pressure is
125 psi. If daytime pressure is over 80
psi, night time pressure may exceed the
maximum. Use a pressure reducing valve
to reduce the flow if necessary.
 WARNING: Discard all unused parts and
packaging material after installation. Small
parts remaining after the installation could
be a choke hazard.
3

Specifications
 Continuous operation at flow rates greater than the service flow
rate may affect capacity and efficiency performance.
 The manufacturer reserves the right to make product improve-
ments which may deviate from the specifications and descriptions
stated herein, without obligation to change previously manufac-
tured products or to note the change.
 Peak flow rates are intended for intermittent use only and are for
residential application only
 At the stated service flow rates, the pressure drop through these
devices will not exceed 15 psig
SpecificationsWG185ACF75WG185ACF10WG185ACF15WG185ACF20WG185ACF30
21502151215221532220
NormalServiceFlowRate4.0gpm5.0gpm7.0gpm10gpm12.0gpm
PeakServiceFlowRate5.0gpm7.0gpm10.0gpm12.0gpm15.0gpm
BackwashFlowRate3.5gpm4.0gpm5.0gpm7.0gpm10.0gpm
FilterMediaVolume‐CubicFeet0.75ft31.0ft31.5ft32.0ft33.0ft3
FilterTankSize8x449x4810x5412x5214x65
TankJacket/MediaLoadedYesYesYesNoNo
ShippingWeight50lbs60lbs78lbs95lbs138lbs
     
    
    
 

 



 

 







     
SpecificationsWG185MMF75WG185MMF10WG185MMF15WG185MMF20WG185MMF30
21662167216821692225
NormalServiceFlowRate4.0gpm5.0gpm7.0gpm10.0gpm12.0gpm
PeakServiceFlowRate5.0gpm7.0gpm10.0gpm12.0gpm15.0gpm
MicronRating15‐20micron15‐20micron15‐20micron15‐20micron15‐20micron
BackwashFlowRate4.0gpm5.0gpm7.0gpm10.0gpm14.0gpm
FilterMediaVolume‐CubicFeet0.75ft31.0ft31.5ft32.0ft33.0ft3
FilterTankSize8x449x4810x5412x5214x65
TankJacket/MediaLoadedYesYesYesNoNo
ShippingWeight79lbs118lbs144lbs198lbs342lbs
     
Specifications
WG185UL‐
TRAMF75
WG185UL‐
TRAMF10
WG185UL‐
TRAMF15
WG185UL‐
TRAMF20
2170217121722173
NormalServiceFlowRate4.0gpm5.0gpm8.0gpm10.0gpm
PeakServiceFlowRate7.0gpm8.0gpm10.0gpm12gpm
MicronRating3‐5micron3‐5micron3‐5micron3‐5micron
BackwashFlowRate5.0gpm7.0gpm10.0gpm14.0gpm
FilterMediaVolume‐CubicFeet0.75ft31.0ft31.5ft32.0ft3
FilterTankSize8x449x4810x5412x52
TankJacketYesYesYesNo
ShippingWeight90lbs135lbs205lbs255lbs
Specifications WG185NNF
75 WG185NNF 10 WG185NNF 15 WG185NNF 20 WG185NNF 30 WG185NNF1 0CALC WG185NNF1 5CALC
2174 2175 2176 2177 2226 2227 2228
Normal Service Flow Rate 2.0 gpm 3.0 gpm 5.0 gpm 6.0 gpm 7.0 gpm 3.0 gpm 5.0 gpm
Peak Service Flow Rate 3.5 gpm 5.0 gpm 8.0 gpm 10.0 gpm 12.0 gpm 5.0 gpm 8.0 gpm
Backwash Flow Rate 3.5 gpm 4.0 gpm 5.0 gpm 7.0 gpm 10.0 gpm 4.0 gpm 5.0 gpm
Filter Media Volume - Cubic
Feet 0.75 ft3 1.0 ft3 1.5 ft3 2.0 ft3 3.0 ft3 1.0 ft3 1.5 ft3
Filter Tank Size 8x44 9x48 10x54 12x52 14x65 9x48 10x54
Tank Jacket / Media Loaded Yes Yes Yes No No Yes Yes
Shipping Weight 93 lbs 120 lbs 164 lbs 207 lbs 330 lbs 120 lbs 164 lbs
For low pH applications
4

Before Starting Installation
Tools, Pipe, and Fittings, Other Materials
 Pliers
 Screwdriver
 Teflon tape
 Razor knife
 Two adjustable wrenches
 Additional tools may be required if modifi-
cation to home plumbing is required.
 Plastic inlet and outlet fittings are included
with the filter. To maintain full valve flow,
3/4” or 1” pipes to and from the filter fit-
tings are recommended. You should main-
tain the same, or larger, pipe size as the
water supply pipe, up to the softener inlet
and outlet.
 Use copper, brass, or PEX pipe and fittings.
 Some codes may also allow PVC plastic
pipe.
 ALWAYS install the included bypass valve,
or 3 shut-off valves. Bypass valves let you
turn off water to the filter for repairs if
needed, but still have water in the house
pipes.
 5/8” OD drain line is needed for the valve
drain. A 10’ length of hose is included.
with some models.
Taste & Odor Filter (Activated Carbon)
Unpleasant tastes and doors caused by chlorine or organic substances, such as decayed
vegetation and run off, are absorbed by top quality activated carbon. The filter will auto-
matically backwash to a predetermined schedule. This frees the bed of accumulated impuri-
ties and readies it for operation again.
Multimedia Filter
Suspended particulate matter, such as clay and silt, which gives water a cloudy appearance,
s trapped in the filter bed to produce clean, clear water. A variety of gravels and sand facili-
tates more thorough backwashing and prevents channeling
Nextsand (Ultramicro Filter)
This filter uses nextsand media for fine filtration of silt, sediment and turbidity. It provides
higher solid loading, longer running times and superior performance. Please refer to special
startup requirement of this media filter.
Neutralizing Filter
The Neutralizing contains special media which raises the pH of acidic water and neutralizes
its acidic characteristics. On some applications, this filter also facilitates the removal of iron
and manganese by raising the pH to enable an iron filter to be used. Occasional backwash-
ing cleans the bed. Over a period of time, additional media may be required. The fill port
options on the tanks make it easier for additional media refilling.
5

 Place the filter tank as close as possible to
the pressure tank (well system) or water
meter (city water).
 Place the filter tank as close as possible to
a floor drain, or other acceptable drain
point (laundry tub, sump, standpipe, etc.).
 Connect the filter to the main water supply
pipe BEFORE the water heater. DO NOT
RUN HOT WATER THROUGH THE FIL-
TER. Temperature of water passing
through the filter must be less than 100
deg. F.
 Do not install the filter in a place where it
could freeze. Damage caused by freez-
ing is not covered by the warranty.
 Put the filter in a place water damage is
least likely to occur if a leak develops. The
manufacturer will not repair or pay for wa-
ter damage.
 A 120 volt electric outlet, to plug the in-
cluded transformer into, is needed within 6
feet of the filter. The transformer has an
attached 6 foot power cable. Be sure the
electric outlet and transformer are in
an inside location, to protect from
wet weather.
 If installing in an outside location, you
must take the steps necessary to assure
the filter, installation plumbing, wiring,
etc., are as well protected from the ele-
ments, contamination, vandalism, etc., as
when installed indoors.
 Keep the filter out of direct sunlight.
The sun’s heat may soften and distort
plastic parts.
Where To Install The Filter
6

Sizing Requirements
Water Pressure
The water system must have a pump big enough to deliver the recommended backwash
rate with a minimum pressure at the inlet of the filter of 30 psi. If the existing system can-
not do this, it must be upgraded to do so. Whenever possible, the water system should be
adjusted to deliver at least 30 psi for even more satisfactory results.
Backwash Flow Rates
The most important criteria in sizing a filter is the capacity of the pump. The water must
pass through the filter media at the proper service flow rate. The filter must also be back-
washed at a flow rate sufficient to dislodge and remove the captured particles. Failure to
provide sufficient water will cause a build-up of particles in the filter media, impairing its
ability. In order for your filter to backwash and rinse properly, your pump must be capable
of providing the backwash flow rates indicated on page 4.
Check Your Pumping Rate
Two water system conditions must be checked carefully to avoid unsatisfactory operation or
equipment damage:
1. Minimum water pressure required at the filter tank inlet is 20 psi.
2. Measuring the pumping rate of your pump:
With the pressure tank full, draw water into a container of known volume, and measure the
number of gallons drawn until the pump starts again. This is draw-down. Divide this figure
by cycle time and multiply the result by 60 to arrive at the pumping rate in gallons per min-
ute (gpm). To aid in your calculation, insert the date in the following formula:
DRAW-DOWN ______ ÷ CYCLE TIME _______ x 60 = PUMPING RATE ________ (gals)
(secs.) (Gpm)
EXAMPLE: CYCLE TIME is 53 seconds. DRAW-DOWN is 6 gallons; then, PUMPING
RATE equals:
6 gallons ÷ 53 seconds x 60 = 6.8 gpm
See chart on page 4 for minimum flow rates.
NOTE: If your pumping rate is inadequate for the model, do not install your filter until
the problem has been corrected.
7

1. If your hot water tank is electric, turn off the power to it to avoid damage to the element
in the tank.
2. If you have a private well, turn the power off to the pump and then shut off the main wa-
ter shut off valve. If you have municipal water, simply shut off the main valve. Go to the
faucet, (preferably on the lowest floor of the house) turn on the cold water until all pres-
sure is relieved and the flow of water stops.
3. Locate the filter tank close to a drain where the system will be installed. The surface
should be clean and level.
4. Connect the inlet and outlet of the filter using appropriate fittings. Perform all plumbing
according to local plumbing codes.
 Use a ½” minimum pipe or tubing size for the drain line
 ON COPPER PLUMBING SYSTEMS BE SURE TO INSTALL A GROUNDING
WIRE BETWEEN THE INLET AND OUTLET PIPING TO MAINTAIN GROUND-
ING.
Any solder joints near the valve must be done before connecting any piping to the valve.
Always leave at least 6" (152 mm) between the valve and joints when soldering pipes that
are connected to the valve. Failure to do this could cause damage to the valve.
5. Connect the drain hose (10 ft included) to the valve and secure it with a hose clamp (also
included). Run the drain hose to the nearest laundry tub or drain pipe. This can be ran
up overhead or down along the floor. If running the drain line more than 20 ft overhead,
it is recommended to increase the hose size to 3/4”. NEVER MAKE A DIRECT CONNEC-
TION INTO A WASTE DRAIN. A PHYSICAL AIR GAP OF AT LEAST 1.5” SHOULD BE USED
TO AVOID BACTERIA AND WASTEWATER TRAVELLING BACK THROUGH THE DRAIN
LINE INTO THE FILTER.
6. Using the Allen Key (included), place the unit in the bypass position. Slowly turn on the
main water supply. At the nearest cold treated water tap nearby remove the faucet
screen, open the faucet and let water run a few minutes or until the system is free of any
air or foreign material resulting from the plumbing work.
7. Make sure there are no leaks in the plumbing system before proceeding. Close the water
tap when water runs clean.
8. Proceed to start up instructions.
Note: The unit is not ready for service until you complete the start-up instruc-
tions.
Installation Instructions
8

Filter Installation
9

System Start-Up
1. Plug the valve into an approved power source.
2. When power is supplied to the control, the screen will display “INITIALIZING WAIT
PLEASE” while it finds the service position.
3. Start an Immediate Manual Regeneration. The valve will immediately start moving to the
BACKWASH position.
4. Open the inlet on the bypass valve slightly and very slowly allow water to en-
ter the unit. (If the water enters too quickly it will push the carbon up into the
control valve and get plugged).
5. Once the unit has filled sufficiently that water is at least equal to the height of
the top of the media shut down the water for 15 – 20 minutes for the carbon
to soak. Unplug the power cable. After the carbon has soaked for the recom-
mended time continue by plugging the power cable back in.
6. Press any button to advance to the RINSE position. Check the drain line flow. Allow the
water to run for 3-4 minutes or until the water is clear.
7. The valve will automatically advance to the SERVICE position after the RINSE cycle is
complete. Open the outlet valve on the bypass, then open the nearest treated water fau-
cet and allow the water to run until clear, close the tap and replace the faucet screen.
8. Program time, date, and number of days between regenerations into controller using
Programming Instructions
Start-up Instructions
Key Pad Configuration
SETTINGSThisfunctionistoenterthebasicsetupinfor‐
mationrequiredatthetimeofinstallation.
MANUAL
REGEN
Thisfunctionistoinitiateanimmediateor
delayedmanualregeneration.
DOWN/
UP
Increaseordecreasethevalueofthesettings
whileintheprogrammingmode.
DELAYED REGENERATION
Press and release the MANUAL REGEN. But-
ton to set a delayed regeneration that will
occur at the regeneration time. The main
display page will show DELAYED REGEN ON.
To cancel press and release the MANUAL RE-
GEN. Button. The main display page will
show DELAYED REGEN OFF.
IMMEDIATE REGENERATION
To start an immediate regeneration (or step
valve through each position), press and hold
the MANUAL REGEN. Button for 3 seconds
(until beeps). The valve will start an immedi-
ate regeneration. Press any key to skip to
the next cycle.
Manual Regeneration (Step / Cycle Valve)
SETTINGS MANUAL
REGEN UP DOWN
10

The table below can be used to help deter-
mine the frequency of regeneration for Multi-
Media and Taste & Odour filters. Use this ta-
ble as a guide since individual circumstances
will require more or less frequent regenera-
tions. This can be adjusted by the home
owner to suite their individual needs with fre-
quencies available from 1 – 99 days.
To prevent bacterial build up in the media,
activated carbon filters should not exceed 6
days between backwashes.
To set a Neutralizing filter, follow the table
under mild conditions
Sediment Mild Average Extreme
Taste Odor Mild Average Extreme
No. Of Per-
sons Days Between Back Wash (Regenerations)
26666666666444444
36666444444333333
46666444333222222
56644333322221111
66644333222211111
76443322211111111
86443222211111111
94433221111111111
10 4332211111111111
Backwash Frequency
Programming Instructions
TIME OF DAY, YEAR, MONTH, DAY,
Time of day is for normal operation of system and the scheduling of the
regeneration time. The date is used in a diagnostic function to track the
last time the system regenerated.
REGEN DAYS
This value is the number of days between regenerations or back washes to
clean the filters.
GALLONS
Default value is OFF. Adjust the GALLONS to set the capacity. This will
cause the unit to regenerate either when the gallons remaining goes to
zero or the days between regeneration is zero. Which ever occurs first.
REGEN TIME
This setting determines the time of day to perform a scheduled regenera-
tion. The normal regen time for a filter is 12:00 AM.
Settings
PressSETINGSkey(3SECONDS/BEEP)
VALVEMODE
B.W.FILTER
TIMEOFDAY
12:01PM
YEAR
2012
MONTH
AUGUST
DAY
21
REGENDAYS
3DAYS
GALLONS
OFF
REGENTIME
12:00AM
PROGRAMMING
COMPLETE
11

Control Operation During A Power Failure
In the event of a power failure, the valve will keep track of the time and day for 48 hours.
The programmed settings are stored in a non-volatile memory and will not be lost during a
power failure. If power fails while the unit is in regeneration, the valve will finish regenera-
tion from the point it is at once power is restored. If the valve misses a scheduled regen-
eration due to a power failure, it will queue a regeneration at the next regeneration time
once power is restored.
Main Display
About The System
Periodically the filter will require a back wash to clean the trapped particles and unpack the
filter bed to restore the system flow rates. The table below explains the regeneration steps.
Regeneration Process
Step Name Description
#1 BackWash
Freshwaterisintroducedtothebottomofthetankflowingupwardsexpanding
thefiltermediatorinseoutanydirtorsmallparticlestothedrainandtoun‐
compactthebedtorestorefullserviceflowrates.
#2 Rinse Freshwaterisintroducedfromthetopofthetankflowingdownthroughthe
filterbedrinsinganyunfilteredwatertothedrain.
The main display page will pause on the Date and Time page for 5 seconds. Then it will
continually scroll through all of the system diagnostic display pages. Depending on the
Valve Type some pages will not be displayed. To manually scroll through the diagnostics,
press the down or up key. To reset the TOTAL REGENS, TOTAL GALLONS OVER RUN TO-
TAL, or PEAK flow rates, press and hold the MENU until the value changes to zero.
PARAMETER DESCRIPTION
JULY/17/2012
8:30PM
TOTAL1,500GAL
REMAIN1,200GAL
LASTREGEN
9/24/12
TOTALREGENS
1
0
TOTALGALLONS
001590GAL
TOTAL4DAYS
REMAIN3DAYS
OVERRUNTOTAL
0000GAL
CURRENT1.5GPM
PEAK6.5GPM
DELAYEDREGEN
OFF
REGENTIME
12:00AM
VALVEMODE
B.W.FILTER
Thecurrentsettingforregenerationtime.
Thecurrentsettingofthevalvemode.
Thetotalnumberofregenerations.
Thetotalamountofgallonstreatedbythesystem.
Thetotalamountofwaterthathasexceededthesystemcapacityoverthelast4
regenerations.Whenremaininggoestozero,thegallonsusedwillbeaddedtooverruntotal.
Thecurrentflowrateandthepeakflowratesincethelastregeneration.
Adviseswhetheradelayedregenerationhasbeenscheduledmanuallyorautomatically.
Month,Day,Year,Time
Thenumberofdaysremainingbeforeregeneration.Thisoptionisonlyinfiltermode.
Thetotalamountisthesystemcapacitywhenfullyregenerated.Theremainingisthe
capacityleftinthesystem.
Thedateofthelastregeneration.
12

Automatic Raw Water Bypass During Regeneration
The regeneration cycle can last 30 minutes after which filtered water service will be re-
stored. During regeneration, un-filtered water is automatically bypassed for use in the
household. Hot water should be used as little as possible during this time to prevent un-
filtered water from filling the water heater. This is why automatic regeneration is set for
sometime during the night and manual regenerations should be performed when little or no
water will be used in the household.
Normal regeneration time is 12:00 AM.
New Sounds
You may notice new sounds as your filter operates. The regeneration cycle lasts up to 30
minutes. During this time, you may hear water running intermittently to the drain.
Manual Bypass
In the case of emergency you can isolate your water filter from the water supply using the
bypass valve located at the back of the control. In normal operation the bypass is open with
the on/off knobs in line with the inlet and outlet pipes.
To isolate the filter, simply rotate the knobs clockwise (as indicated by the word BYPASS
and arrow) until they lock. You can use your water related fixtures and appliances as the
water supply is bypassing the filter. However, the water you use will be hard. To resume
water service, open bypass valve by rotating the knobs counterclockwise.
System Configuration
TankSize(Diameter) DrainLineFlow
Control(DLFC)
8" #5(3.5GPM)
9" #A(5.0GPM)
10" #A(5.0GPM)
12" #B(7.0GPM)
14" #C(10.0GPM)
16" none
SuggestedFilterValveConfiguration
13

Maintenance
Care of Your System
To retain the attractive appearance of your new water filter, clean occasionally with mild
soap solution. Do not use abrasive cleaners, ammonia or solvents. Never subject your sof-
tener to freezing or to temperatures above 100°F.
Maintenance of your new water filter requires very little time or effort but it is essential.
Regular maintenance will ensure many years of efficient and trouble-free operation.
1. Periodically make sure your pump is performing satisfactorily to ensure sufficient water is
available for backwashing the filter.
2. Periodically test your raw and filtered water to ensure conditions are still the same for
your original settings and that the unit is working they way it is intended to. Water test-
ing is often the best way to determine when the filter media will require replacement.
3. Periodically check that the drain line is clear and free from any obstructions.
NFF- Neutralizing Filter - the media bed in a neutralizing filter is slowly dissolved and has
to be replaced. The frequency of replacement varies, depending on water quality - consult
your dealer to determine the expected life of your media bed.
AC and CLAF- Taste and Odor Filter - under normal operating conditions the effective
life of the filter media is approximately one to three years, depending on the water quality,
after which, taste and odor problems may return. When this happens, contact your dealer
for a replacement media bed.
MM - Sediment and Turbidity Filter - under normal operating conditions, the media
should never need to be replaced. However, if you experience pressure loss and cannot cor-
rect it with a manual regeneration, your media bed may need replacing - contact your
dealer.
Replacing the Media Bed
Check to ensure all media parts are received.
The first step in replacing the media bed is to shut off the water supply to the filter. Then
place the unit into the backwash position to release any pressure in the lines. At this point,
you must disconnect the plumbing from the inlet and outlet. Then unscrew the control
valve from the fibreglass tank. Once this has been done, remove the distributor tube. Then
you can remove the filter media and two types of gravel from the tank. The quickest way to
do this is by simply tipping the tank upside down into a large drum or pail. The tank must
be rinsed out completely and have no media or gravel left in it at all.
Installation & Replacement Filter Media Pak
14

Loading the Media Pak
Place the distributor tube back down the center of the tank. NOTE: the top of this tube
should be plugged with a rag or cork to prevent media from entering. Pour the bag of
coarse gravel into the tank, and then pour the bag of fine gravel into the tank.
It is important that the distributor tube is not moved or pulled out as it is not possible to put
it down to the bottom of the tank once gravel or media are in the tank.
Finally pour the larger bag(s) of media into the tank in the following order:
Multimedia Filters
1. Coarse gravel (1/2 x 1/4) 4. Fine garnet (30 x 40)
2. Fine gravel (1/8 x 1/16) 5. Fine filter sand (.45 x .55)
3. Coarse gravel (8 x 12) 6. Anthrafilt
ACF Carbon Filters Neutralizing Filters
1. Coarse gravel 1. Coarse gravel 4. Mag Oxide
2. Fine gravel 2. Fine gravel
3. Carbon 3. Calcite
UltramicroFilters
1. Coarse gravel (1/2 x 1/4)
2. Fine gravel (1/8 x 1/16)
3. Nextsand media
Once this is done, the rag or cork should be removed from the distributor tube. Clean off
the top of the tank. Finally place the control valve on the tank and on to the distributor
tube. Tighten the control valve on to the tank. Connect or reconnect the inlet and outlet and
drain. The control valve should be in the backwash position. Slowly open the inlet valve wa-
ter supply and slowly fill the filter tank until water appears at the open drain line. Return the
15

Replacing Drain Line Flow Control (DLFC)
1. Remove the red clip that secures the drain line elbow.
2. Remove the BLFC washer from the elbow fitting.
3. Reassemble using the reverse procedure.
16

A A A
B
D
F
E
A
C
Replacement Part Number Part Description DWG # Quantity
60010020 3/4" NPT ELBOW
A2
60010019 1" NPT STRAIGHT A2
60010023 3/4" NPT STRAIGHT
A2
60010079 VALVE COUPLING INLET
B1
60010101 VALVE COUPLING OUTLET (METER SIDE)
C1
60010025 PLASTIC SECURE CLIP D2
60010046 BYPASS SS CLIP E2
60010047 BYPASS SS SCREW F 2
REPLACEMENT PARTS - CONNECTORS
Main Repair Parts - Connectors
17

VALVE REPAIR PARTS LIST
Replacement
Part Number Part Description Replacement Part Number Part Description
60010127INJECTORSET#0000BLACK6001012985HEUPFLOWPISTONASSEMBLY
60010126INJECTTORSET#000GREY6001017185HEDOWNFLOWPISTONASSEMBLY
60010035INJECTORSET#00VIOLET6001013085HESEAL&SPACERKIT
60010034INJECTORSET#0RED6001013185HEDLFC#11.5GPM
60010033INJECTORSET#1WHITE6001013285HEDLFC#22.0GPM
60010032INJECTORSET#2BLUE6001013385HEDLFC#32.4GPM
60010031INJECTORSET#3YELLOW6001013585HEDLFC#53.5GPM
60010128BLFC0.2GPM6001013685HEDLFC#A5.0GPM
60010110BLFC0.3GPM6001013785HEDLFC#B7.0GPM
60010082BLFC0.7GPM6001013885HEDLFC#C10.0GPM
Control Valve Exploded View
18

185HE CONTROL VALVE (DOWNFLOW)
Replacement
Part Number MFG Part Number Part Description DWG # Quantity
5056087 Screw-M5x12(Hexagon) A01 3
5056088 Screw-M5x16(Hexagon With Washer) A02 2
5056047 End Plug Retainer A03 1
5031016 BNT85HE Piston Rod A04 1
5056097 Piston Pin A05 1
5031015 BNT85HE Quad Ring Plug Cover A06 1
5056070 Quad Ring A07 2
5031011 BNT85HE End Plug A08 1
5031014 BNT85HE Piston Retainer A09 1
5057001 BNT85HE Piston(Electrical Downflow) A10 1
5056073 Seal A11 5
5056021 Spacer A12 4
5010082 Drain Fitting-B A13 1
5031005 BNT85HE Spacer A14 1
5056186 DLFC-2# A15 1
5056172 Secure Clip-s A16 2
5031002 BNT85HE Valve Body A17 1
5056508 Screw-M5x12(Hexagon With Washer) A18 5
5030004 BNT85 End Cover A19 1
5030013 O-Ring-¢30×2.65 A20 1
5056063 O-Ring-¢78.74×5.33 A21 1
26010103 O-Ring-¢25×3.55 A22 1
7060007 Valve Bottom Connector A23 1
13000426 Screw-ST2.9X13(Large Washer) A24 2
5031022 O-Ring-¢32×3 A25 1
5031021 O-Ring-¢18×3 A26 1
5031013 Injector Plug Body A27 1
30110007 Plastic Ball ¢6 A28 1
30040089 Injector Throat A29 2
5031012 BNT85HE Injector Fixed Sleeve A30 1
30040090 Injector Nozzle A31 2
5056103 Injector Screen A32 1
5031003 BNT85HE Injector Cover Body A33 1
5031018 O-Ring-¢40×2.65 A34 1
5031004 BNT85HE Injector Cover Cap A35 1
5031027 Screw-M5x25(Hexagon With Washer) A36 4
5056075 Seal Mat A37 1
5056134 O-Ring-¢12×2 A38 3
5056054 Injector Stem A39 1
5056031 Injector Spacer A40 1
5056081 O-Ring-¢12.5×1.8 A41 1
5056030 Injector Cap A42 1
5056093 Injector Screen A43 1
5010049 Special Washer A44 1
5056105 Retaining Ring A45 1
5031010 BNT85HE BLFC Fixed Sleeve A46 2
5056076 BLFC-2# A47 1
5005629 Injector Fitting(3/8".Elbow) A48 1
Control Valve Parts List
19

Power Head Exploded View
20