Waterpik Sonic-Fusion SF-01 User manual

Waterpik®Sonic-Fusion®
Models SF-01 | SF-02
•
8
•
6
•
4
•
2
•
Brush
Floss
•
8
•
6
•
4
•
2
•
Brush
Floss
www.waterpik.co.uk

2
IMPORTANT SAFEGUARDS
IMPORTANT
SAFEGUARDS
READ ALL INSTRUCTIONS
BEFORE USING.
• This product is for household use.
When using electrical products, especially
when children are present, basic safety
precautions should always be followed,
including the following:
DANGER:
To reduce the risk of
electrocution:
• Do not handle plug with
wet hands.
• Do not place in or drop
into water or other liquid.
• Do not use while bathing.
• Do not place or store product where it can fall
or be pulled into a tub or sink.
• Do not reach for a product that has fallen
into water. Unplug immediately.
• Check the power supply cord for damage
before the rst use and during the life of
the product.
• The supply cord cannot be replaced. If the
cord is damaged the appliance should be
scrapped.
WARNING:
To reduce the risk of burns,
electrocution, ire, or injury to
persons:
• Do not plug this device into a voltage system
that is dierent from the voltage system
specied on the device.
• If product is opened/disassembled for ANY
reason, warranty is VOID.
• Do not use this product if it has a damaged
cord or plug, if it is not working properly,
if it has been dropped or damaged, or
dropped into any liquid. Contact Water Pik,
International, Inc. UK Service
Centre at [phone].
• Do not direct water under the tongue,
into the ear, nose or other delicate areas.
This product is capable of producing
pressures that may cause serious damage
in these areas.
• Use this product only as indicated in these
instructions or as recommended by your
dental professional.
• Only use ossing brush heads and accessories
recommended by Water Pik, Inc.
• Do not drop or insert any foreign object into
any opening or hose.
• The power handle should only be used with
the charging base provided.
Brush
Floss

ENGLISH
3
• Keep electrical cord away from
heated surfaces.
• Do not use outdoors or operate where aerosol
(spray) products are being used or where
oxygen is being administered.
• Fill reservoir with water or other dental
professional recommended solutions only.
• Remove any oral jewelry prior to use.
• Do not use if you have an open wound on your
tongue or in your mouth.
• If your physician or cardiologist has advised
you to receive antibiotic premedication
before dental procedures, you should consult
your dentist and/or medical professional
before using this product or any other oral
hygiene aid.
• Do not use iodine or water insoluble
concentrated essential oils in this product.
Use of these can reduce product performance
and will shorten the life of the product.
Use of these products may void warranty.
• Close supervision is necessary when
this product is used by, on or near children
or invalids.
• Magnetic eld: Pacemakers and similar
implanted medical devices may be aected
by magnet.
• Do not use the toothbrush motor for more
than 5 minutes in each 10 minute period.
• Using toothpastes containing peroxide may
damage the plastic housing of this product.
• Using abrasive or chemical cleaners may
damage the plastic housing of this product.
• Closely instruct and supervise
children 8 years and above
and individuals with special
needs in the proper use of
this product.
• Children should be supervised
to ensure that they do not
play with the appliance.
• This product does not contain
any user serviceable parts. Do
not attempt to open except
for battery disposal. See
“Battery Removal” section.
• Fill Water Flosser reservoir
with warm water or
other dental professional
recommended solutions only.
• IMPORTANT This device uses
wireless communication to control the
ON/OFF function of the water osser pump
motor from the toothbrush power handle.
This device was designed for Home or Oce
use. To avoid electromagnetic interference,
do not operate this device in restricted
locations such as aircras or specially
marked areas in hospitals.
SAVE THESE
INSTRUCTIONS

4
TABLE OF CONTENTS
Product Description 5
Preparing The Unit/Brushing and Flossing 6
Care and Maintenance 8
Limited Three-Year Warranty 10

ENGLISH
5
PRODUCT DESCRIPTION
1. Brush head
2. Water flosser nozzle
3. Hinged Lid
4. Reservoir
5. Water hose
6. Water flosser pressure
control dial
7. Water hose release button
8. Toothbrush ON/OFF button
9. Motion activated ring lights*
10.Water flosser ON/OFF button
11. Power handle
12. Toothbrush charge
indicator lights
13. Power cord
14. Charging base
15.Indicator Light
•
8
•
6
•
4
•
2
•
Brush
Floss
1
2
8
9
10
14
15
11
12
13
6
7
5
4
3
Recommendation:
replace brush
head every 3
months
*select models only

6
Preparing the Unit
Powering the Unit
Plug the cord into an electrical outlet. If the outlet is controlled by a wall switch, be
sure it is turned on.
Attaching the Brush Head to the Power Handle
Position the brush head on the power handle as shown. Press rmly until it clicks into
place. To remove, rmly pull the brush head to separate it from the power handle.
Attaching the Power Handle to the Hose
Position the power handle onto hose in the base. Press the power handle rmly onto
the hose attachment until it clicks into place. To remove, simply press the round
button on the back side of the power handle.
Charging the Sonic-Fusion®
Charge for at least 20 minutes before rst use by placing the handle on the charging
base. For a full charge, leave the handle on the charging base for at least 4 hours. A
full charge should last 14 uses with a duration of 2 minutes each. If the toothbrush
is to be stored for an extended period of time (six months or more), be sure to fully
charge it (at least 4 hours) prior to storage.
Charge Lights
Toothbrush charge indicator lights will indicate level of battery charge for
approximately 10 seconds aer removal from the charging base and aer use, and
will then turn o. If only the bottom light is lit, then recharging is recommended to
ensure uninterrupted use.
Indicator Light
The blue light blinks when:
• The unit is rst plugged in
• The handle is placed in charger
• The handle is removed from the charger
• A wireless command is received
Preparing the Reservoir
Remove reservoir and open hinged lid. Fill the reservoir with warm water. Close the
lid and replace the reservoir on the base and press rmly.
Prime Unit (First Time Use Only)
Point the brush head tip into the sink. Press the Floss button and repeatedly rotate
the pressure control dial between low and high until water ows.
Aer water ows from the nozzle, press the FLOSS button to turn water OFF.
PREPARING THE UNIT / BRUSHING AND FLOSSING
Brush
Floss
Brush
Floss
Brush
Floss
•
8
•
6
•
4
•
2
•
Brush
Floss
•
8
•
6
•
4
•
2
•
Brush
Floss
Click
Click
Charge
Blue
Light
Fill
Brush
Floss
Floss
•
8
•
6
•
4
•
2
•
High
Low

7
ENGLISH
Brushing
Place the brush head in your mouth before pressing the BRUSH button.
Recommended Technique
For best results, position brush along gumline at a 45-degree angle. Press the BRUSH
button to turn the brush ON. Use light pressure and move the toothbrush slowly
allowing for the sonic action to clean each tooth individually. Brush can be easily
disconnected from the hose if desired (See diagram on product description page).
Quad Timer
The Sonic-Fusion® will create a short pause every 30 seconds to remind you to move
to the next section of your mouth. You will brush the outside of the teeth for 30
seconds and then the inside for 30 seconds. This will be repeated on the other arch
for a total of 2 minutes to clean all teeth.
2-Minute Timer
The brush will automatically shut o aer 2 minutes of run time.
Water Flossing
Always place the brush head in your mouth prior to pressing the FLOSS button. Lean
over the sink and slightly close lips enough to prevent splashing while still allowing
water to ow from mouth into sink.
Adjusting the Pressure Setting
Turn the water osser pressure control dial on the base of the unit to the lowest
setting (pressure setting No. 1) for rst-time use. Gradually increase pressure over
time to the setting you prefer – or as instructed by your dental professional.
Recommended Technique
For best results, start with the back teeth and work toward the front teeth.
Direct the brush head so that the water osser nozzle is angled slightly toward the
gumline. Move the brush head along the gumline pausing briey between each tooth
to allow water to clean between teeth. Continue until you have cleaned the inside
and outside of both the upper and lower teeth. When nished, empty any liquid le
in the reservoir.
NOTE: If you used mouthwash or any other solution besides water, see “Using
Mouthwash and Other Solutions” section.
Brush + Floss
To Brush + Floss at the same time, place brush head in mouth. Press brush button,
then press oss button.
30 sec.
30 sec.
30 sec.
30 sec.
•
8
•
6
•
4
•
2
•
Adjust
Brush
Brush
Floss
Brush +
Floss

8
Travel and Hose-Free Brushing
Toothbrush can be disconnected from the Sonic-Fusion® for travel or hose-free
brushing. Place the handle and desired brush head(s) in the provided case for
protection when traveling.
NOTE: To disconnect the toothbrush from the water hose, press the round button
on the back side of the power handle.
Using Mouthwash and Other Solutions
Your Waterpik® Sonic-Fusion® can be used to deliver mouthwash and antibacterial
solutions. Aer using any special solution, rinse unit to prevent clogging by partially
lling reservoir with warm water and running unit with brush head pointed into sink.
Care and Maintenance
Before cleaning, unplug from the electrical outlet.
After Each Use
1. Aer each use, when all functions are turned OFF, remove the brush head
from the handle and rinse brush head and handle under running water.
2. Wipe the handle dry aer each use.
3. Store handle on charger and keep unit plugged in.
The unit will not overcharge.
General Cleaning / Removing Hard Water Deposits
• Clean the product when necessary by using a so cloth and mild
non-abrasive cleanser.
• Hard water deposits may build up in your unit, depending on the mineral content
of your water. If le unattended, it can hinder performance. Cleaning internal
parts: add 2 tablespoons of white vinegar to a full reservoir of warm water.
Point the handle and brush head into sink. Turn Water Flosser ON and run until
reservoir is empty. Rinse by repeating with a full reservoir of clean warm water.
This process should be done every 1 to 3 months to ensure optimal performance.
Toothbrush Low Charge Lock Out
The toothbrush charge indicator lights will ash if the battery charge is too low for
brushing. This may cause the toothbrush to enter Lock Out mode. To clear the Lock
Out, place the power handle on the charging base.
Leakage
If leaking due to a damaged hose, please contact Water Pik, International, Inc. UK
Service Centre at [phone].
CARE AND MAINTENANCE
Brush
Floss
•
8
•
6
•
4
•
2
•
Brush
Floss
Brush
Floss

9
ENGLISH
Multiple Unit Proximity
To avoid wireless communication interference when more than one unit will be
used in proximity, go to (waterpik.com/MUP) for instruction for changing the base
and handle ID.
Battery Removal
This product contains rechargeable Nickle Metal Hydride batteries. The batteries
are not replaceable. Please do not dispose of the unit in the household waste.
Remove the batteries per the instructions below and recycle at your local
recycling center.
Note: This process is not reversible
Remove the battery only at the end of the product’s life for recycling. Doing so
earlier will destroy the product. Deplete the battery charge until the brush no longer
operates. Observe basic safety precautions to protect your eyes, hands, ngers, and
work surface. Remove the batteries as shown and recycle them and the rest of the
product according to local regulations.
1. Run down the battery by operating the brush button until the motor
does not run.
2. Obtain a towel or cloth, hammer, at-head screwdriver, and wire cutters.
3. Remove and discard the brush head.
4. Cover the handle entirely with the towel or cloth.
5. Clamp the top of the handle against your work surface with one hand and
strike the handle housing around the bottom perimeter on all sides to release
the end cap latch. Continue striking and rotating the handle until the end
cap releases.
6. Remove the internal components by turning the handle upside down and while
holding on to the handle housing, press the sha down rmly on a hard surface.
7. The internal components should slide out when the handle is positioned
upside-down. If this does not occur, repeat steps 5 and 6 until the
components release.
8. Remove the end cap from the internal assembly.
9. Slide the battery out of the internal assembly.
10. Cut the battery wires one at a time with the wire cutters.
11. Recycle and dispose of the battery properly.
12. The remaining product pieces should be discarded appropriately.
Brush
Floss
Brush
Floss
Cut
Remove
Battery

10
Service Maintenance
Waterpik® Water Flossers have no consumer-serviceable electrical items and do
not require routine service maintenance. For all your service needs please call the
Waterpik International, Inc. UK Customer Service Centre at [phone].
Some replacement parts and accessories for the Water Flosser are also available
at www.waterpik.co.uk. For questions or problems please call the customer service
centre before returning the product. Please do not send your unit to the Waterpik
International, Inc. address as this can cause lengthy delays. Refer to the serial and
model numbers in all correspondence. These numbers are located on the bottom of
your unit.
Water Pik, Inc. warrants to the original consumer of this product that it is free from
defects in materials and workmanship for 3 years from the date of purchase.
Save your receipt as your proof of purchase date. Water Pik, Inc. reserves
the right to request the product to be returned for analysis to conrm
the claim falls within our warranty policy. Water Pik, Inc. will replace, at its
discretion, the product provided the product has not been abused, misused, altered
or damaged aer purchase, was used according to instructions, and was used
only with accessories or consumable parts approved by Water Pik, Inc. This limited
warranty excludes accessories or consumable parts such as tips and brush heads.
This warranty gives you specic legal rights. You may also have other rights
that vary depending on the law in your place of residence. Contact Water Pik,
International, Inc. UK Service Centre at [phone].
LIMITED THREEYEAR WARRANTY

11
ENGLISH

Form No. 20028047-F AA
©2020 Water Pik, Inc.
Made in China. Designed and tested in the U.S.A.
Water Pik, Inc., a subsidiary
of Church & Dwight Co., Inc.
1730 East Prospect Road
Fort Collins, CO 80553-0001 USA
844-821-4873
www.waterpik.com
SOFIBEL SAS
92686 Levallois-Perret Cedex-France
Church & Dwight UK LTD.,
Folkestone, CT19 6PG
UK: 0800 121 6080