Waters Network Systems ProSwitch-Secure 1007 User manual

WATERS NETWORK SYSTEMS™
OPERATING MANUAL
ProSwitch-Secure1007 Unmanaged Models
8-Port Enclosed Classroom and Workgroup Switches
CORPORATE HEADQUATERS MANUFACTURING/CUSTOMER SERVICE
5001 American Blvd. W., Suite 605 945 37th Avenue, NW
Bloomington, MN 55437 Rochester, MN 55901
Phone: [phone] Phone: [phone]
Phone: [phone] Phone: [phone]
Fax: [phone] Fax: [phone]
Web site: http://www.watersnet.com

2ProSwitch 1007 – Unmanaged User’s Manual Page 2
TABLE OF CONTENTS
1.0 SPECIFICATIONS ............................................................................................................................. 3
2.0 PACKAGE CONTENTS - PROSWITCH-SECURE-1007 - UNMANAGED.................................... 4
2.1 PRODUCT DESCRIPTION................................................................................................................ 4
2.3 LOCATION OF THE PROSWITCH -SECURE-1007 ........................................................................ 4
3.0 CONNECTING THE PROSWITCH -SECURE 1007 TO YOUR NETWORK .................................... 4
4.0 MOUNTING THE PROSWITCH -SECURE 1007 .............................................................................. 5
5.0 POWERING THE PROSWITCH -SECURE 1007 ............................................................................. 5
6.0 STATUS OF LEDS ............................................................................................................................ 6
7.0 TROUBLESHOOTING....................................................................................................................... 6
7.1 BEFORE CALLING FOR ASSISTANCE .......................................................................................... 6
7.2 RETURN MATERIAL AUTHORIZATION (RMA) PROCEDURE...................................................... 7
7.3 SHIPPING AND PACKAGING INFORMATION ............................................................................... 7
8.0 WARRANTY ...................................................................................................................................... 8

2ProSwitch 1007 – Unmanaged User’s Manual Page 3
1.0 SPECIFICATIONS
OPERATIONAL CHARACTERISTICS:
MAC Address Table:
4K MAC
Switching Mode:
Store and forward
Performance:
Non-blocking switching architectures
Forwarding Rate:
10Mbps: 14,880 pps
100Mbps: 148,800 pps
Memory Buffer Size:
2MB
Auto-negotiation on TX ports
Broadcast storm filter function
NETWORK STANDARDS:
IEEE 802.3u: 100BASE-TX, 100BASE-FX Fast Ethernet
IEEE 802.3: 10BASE-T Ethernet
IEEE 802.3x Flow Control
EMI/SAFETY COMPLIANCE:
CE & FCC
FCC Class A, UL 1950, CSA C22.2 No. 950, EN60950, CE: EN55022 Class A, EN55024
FIBER PORT CHARACTERISTICS:
Multimode with SC, ST or MTRJ connectors
Speed: 100Base-FX
Wavelength: 1300nm
Maximum distance: 2km
Fiber size: 62.5/125, 50/125
Singlemode with SC connector
Speed: 100Base-FX
Wavelength: 1300nm
Maximum distance: 15/40/75km
Fiber size: 8/125, 9/125
NETWORK CABLE CONNECTORS:
10Base-T: CAT3, 4 or 5; up to 100M (328 feet)
100Base-TX: CAT5 or better; up to 100M (328 feet)
POWER SUPPLY:
Power Input Voltage: 100 to 240V; Internal
Power Input Frequency: 50 to 60Hz
Power Consumption: 2A, 15W max
OPERATING ENVIRONMENT:
Ambient: 32° to 104°F (0° to 40°C)
Storage: -13° to 158°F (-25° to 70°C)
Ambient relative humidity: 10% to 90% (non-condensing)
MECHANICAL:
Enclosure: Rugged high-strength sheet metal suitable for stand-alone, wall or tabletop mounting
Cooling Method: Convection cooled
PHYSICAL CHARACTERISTICS:
Dimensions: 16 x 11 x 2 (40.6 x 27.9 x 5.1cm)
Weight: 6.5LBS (2.95kg)

2ProSwitch 1007 – Unmanaged User’s Manual Page 4
2.0 Package Contents - ProSwitch-Secure-1007 - Unmanaged
Examine the shipping container for obvious damage prior to installing this product. Notify the carrier of any damage
that you believe occurred during shipment. Ensure that the items listed below are included.
The ProSwitch -Secure-1007 package contains the following:
8 port switch
AC power cord
2.1 Product Description
A switch can be used to overcome the hub-to-hub connectivity limitations as well as improve overall network
performance. Switches make intelligent decisions about where to send network traffic based on the destination
address of the packet. As a result, the switch can significantly reduce unnecessary traffic. The ProSwitch-Secure
1007 - unmanaged models provide 10/100Base-TX ports with an optional 100Base-FX port in a cost effective pocket
size package. The 10/100Base-TX ports auto negotiate speed and half/full duplex modes.
2.3 Location of the ProSwitch -Secure-1007
The ProSwitch 1007 can be installed quickly and easily. However, for an installation with minimum impact on the
existing network, please read the following information carefully. Installing the ProSwitch 1007 unmanaged switch
involves three steps:
1. Choosing a location
2. Supplying power
3. Connecting the switch
Consider the following criteria when selecting a location for the switch:
Avoid dusty locations
Avoid electromagnetic noisy areas, such as locations close to power transformers or radio transmitters
Avoid temperatures below 32° to 104°F (0° to 40°C)
Allow sufficient space for proper ventilation
Allow a clear view of the front panel LED indicators
Allow easy access to the front panel ports and the rear panel switches
The power outlet should be within six feet (1.8m) of the switch
3.0 Connecting the ProSwitch -Secure 1007 to Your Network
The1007 has been designed to support all standard Ethernet media types within a single switch unit. The various
media types supported along with the corresponding IEEE 802.3 and 802.3u standards and connector types are as
follows:

2ProSwitch 1007 – Unmanaged User’s Manual Page 5
Fiber:
Speed Media Type Max. Distance Connector Type Port Speed
Half/Full Duplex
100Base-FX Multimode fiber 2km SC, ST or MTRJ 100/200Mbps
100Base-FX Singlemode fiber 15, 40 or 75KM SC 100/200Mbps
Copper:
10Base-T CAT3, 4 or 5 100m (328ft) RJ45 10/20Mbps
100Base-TX CAT5 or 5E 100m (328ft) RJ45 100/200Mbps
NOTE: Since all switch ports are auto-sensing for both 10 and 100Mbps, it is recommended that high quality CAT5
cables or above (which work for both 10Mbps and 100Mbps) be used whenever possible in order to provide flexibility
in a mixed-speed network. Because the switch supports auto MDI/MDI-X detection, normal straight through cables
for both workstation connection and hub or switch connection can be used. All ports are auto MDI/MDI-X, so you can
use any of the ports to connect a port on another hub or switch with straight through or crossover cables.
4.0 Mounting the ProSwitch -Secure 1007
Table-Top or Shelf Mounting
The ProSwitch 1007 can be easily mounted on a table-top or any suitable horizontal surface. There are four rubber
feet provided for stability so finished surfaces won’t be scratched.
5.0 Powering the ProSwitch -Secure 1007
The ProSwitch 1007 switch is equipped with a universal power adapter that accepts AC input voltages from 100 to
240VAC and 50 to 60 Hz.
To supply power to your switch:
1. Plug the connector of the power cord into the power port on the rear panel of your switch.
2. Plug the power adapter into an AC wall outlet.
3. Set the power switch to ON and verify that the Power LED is lit. If it is not, check the following:
The power switch is in the ON position
The power cord is properly connected to the wall outlet and to the power connection on the switch.
The wall outlet is functional.
Note: Network cable segments can be connected or disconnected from the switch while the power is on, without
interrupting the operation of the switch.

2ProSwitch 1007 – Unmanaged User’s Manual Page 6
6.0 Status of LEDs
LED STATUS CONDITION
Power ON Switch is receiving power.
ON Port has established a valid link.
Link / Act
Flashing Data packets are being received or sent.
7.0 Troubleshooting
All Waters’ switching products are designed to provide reliability and consistently high performance in all network
environments. The installation of Waters’ ProSwitch -Secure 1007 switch is a straightforward procedure (See
Sections 3-5). Should problems develop during installation or operation, this section is intended to help locate,
identify and correct these types of problems. Please follow the suggestions listed below prior to contacting your
supplier. However, if you are unsure of the procedures described in this section or if the Waters’ ProSwitch -Secure
1007 switch is not performing as expected, do not attempt to repair the unit; instead contact your supplier for
assistance or contact Waters Network Systems’ Customer Support Center at 800.328.2275 or email
[e-mail].
7.1 Before Calling for Assistance
1. If difficulty is encountered when installing or operating the unit, refer back to the Installation Section of the
chapter of this manual. Also check to make sure that the various components of the network are inter-operable.
2. Check the cables and connectors to ensure that they have been properly connected and the cables/wires have
not been crimped or in some way impaired during installation. (About 90% of network downtime can be attributed
to wiring and connector problems.)
3. Make sure that an AC power cord is properly attached to the ProSwitch -Secure 1007.
4. Be certain that each AC power cord is plugged into a functioning electrical outlet. Use the PWR LEDs to verify
each unit is receiving power.
5. If the problem is isolated to a network device other than the Waters’ ProSwitch -Secure 1007 switch, it is
recommended that the problem device be replaced with a known good device. Verify whether or not the problem
is corrected. If not, go to next step. If the problem is corrected, the Waters’ ProSwitch -Secure 1007 switch and
its associated cables are functioning properly.
6. If the problem continues, contact Waters Network Systems Customer Service at 800.328.2275 or email
[e-mail] for assistance.
When Calling for Assistance
Please be prepared to provide the following information.
1. A complete description of the problem, including the following points:
a. The nature and duration of the problem

2ProSwitch 1007 – Unmanaged User’s Manual Page 7
b. Situations when the problem occurs
c. The components involved in the problem
d. Any particular application that, when used, appears to create the problem
2. An accurate list of Waters Network Systems product model(s) involved. Include the date(s) that you purchased
the products from your supplier.
3. It is useful to include other network equipment models and related hardware, including personal computers,
workstations, terminals and printers; plus, the various network media types being used.
4. A record of changes that have been made to your network configuration prior to the occurrence of the problem.
Any changes to system administration procedures should all be noted in this record.
7.2 Return Material Authorization (RMA) Procedure
All returns for repair must be accompanied by a Return Material Authorization (RMA) number. To obtain an RMA
number, call Waters Network Systems Customer Service at 800.328.2275 during business hours of 8:00 am to 5:00
pm (CT) or email [e-mail]. When calling, please have the following information readily available:
Name and phone number of your contact person
Name of your company/institution
Your shipping address
Product name
Packing List Number (or Sales Order Number)
Failure symptoms, including a full description of the problem
Waters Network Systems will carefully test and evaluate all returned products, will repair products that are under
warranty at no charge, and will return the warranty-repaired units to the sender with shipping charges prepaid (see
Warranty Information at the end of this manual for complete details). However, if Waters cannot duplicate the
problem or condition causing the return, the unit will be returned as: No Problem Found.
Waters Network Systems reserves the right to charge for the testing of non-defective units under warranty. Testing
and repair of product that is not under warranty will result in a customer (user) charge.
7.3 Shipping and Packaging Information
Should you need to ship the unit back to Waters Network Systems, please follow these instructions: Package the unit
carefully. It is recommended that you use the original container if available. Units should be wrapped in a "bubble-
wrap" plastic sheet or bag for shipping protection. (You may retain all connectors and this Installation Guide.)
CAUTION: Do not pack the unit in Styrofoam "popcorn" type packing material. This material may cause electro-static
shock damage to the unit.
Clearly mark the Return Material Authorization (RMA) number on the outside of the shipping container. Waters
Network Systems is not responsible for your return shipping charges.
Ship the package to:
Waters Network Systems
Attention: Customer Service
945 37th Avenue, NW
Rochester, MN 55901

2ProSwitch 1007 – Unmanaged User’s Manual Page 8
8.0 Warranty
Waters Network Systems’
Warranty Statement
Waters Network Systems’ products are warranted against defects in materials and workmanship. The warranty
period for each product will be provided upon request at the time of purchase. Unless otherwise stated, the warranty
period is for the useable life of the product.
In the event of a malfunction or other indication of product failure attributable directly to faulty materials and/or
workmanship, Waters Network Systems will, at its option, repair or replace the defective products or components at
no additional charge as set for herein. This limited warranty does not include service to repair damage resulting from
accident, disaster, misuse, neglect, lightning, acts of God, tampering or product modification.
Service under the warranty may be obtained by contacting Waters Network Systems and receiving a Return Material
Authorization (RMA) number from Waters Network Systems. Returned product accompanied with the issued RMA
number and prepaid shipping will be repaired or replaced by Waters Network Systems. Repaired or replaced
products will be returned at no cost to the original Buyer and shipped via the carrier and method of delivery chosen by
Waters Network Systems.
Specific warranty by product family is as follows:
ProSwitch-Secure: Limited Lifetime (see note)
ProSwitch-SecureAir+: Limited Lifetime
ProSwitch-Lite: 3 Years from date of manufacture (see note)
ProSwitch--Secure Xpress: Limited Lifetime
ProSwitch-Xtreme: Limited Lifetime (see note)
ProSwitch-FlexPort: Limited Lifetime
ProSwitch-FixPort: Limited Lifetime
ProSwitch-CS and CSX: 3 Years from date of manufacture (see note)
ProMedia Converters 3 Years from date of manufacture (see note)
Note: Warranty period for any and all external power supplies is one (1) year from date of purchase.
EXCEPT FOR THE EXPRESS WARRANTY SET FORTH ABOVE, WATERS NETWORK SYSTEMS GRANTS NO
OTHER WARRANTIES, EXPRESSED OR IMPLIED, BY STATUTE OR OTHERWISE, REGARDING THE
PRODUCTS, THEIR FITNESS FOR ANY PURPOSE, THEIR QUALITY, THEIR MERCHANTABILITY, OR
OTHERWISE.
WATERS NETWORK SYSTEMS’ LIABILITY UNDER THE WARRANTY SHALL BE LIMITED TO PRODUCT
REPAIR, OR REPLACEMENT OF THE BUYER’S PURCHASE PRICE. IN NO EVENT SHALL WATERS NETWORK
SYSTEMS BE LIABLE FOR THE COST OF PROCUREMENT OF SUBSTITUTE GOODS BY THE CUSTOMER OR
FOR ANY CONSEQENTIAL OR INCIDENTAL DAMAGES FOR BREACH OR WARRANTY.