Waters Network Systems MS1008-2G-4POE User manual

12
OPERATING MANUAL
MS1008-2G-4POE/PSX1008-2G-4PoE Switch
Managed Switch with Eight 10/100/1000Base-TX Ports
Plus One Mini GBIC slot for 1000Base-SX or LX fiber
or one 10/100/1000Base-TX port
Four PoE Ports
CORPORATE HEADQUATERS MANUFACTURING/CUSTOMER SERVICE
5001 American Blvd. W., Suite 605 945 37th Avenue, NW
Bloomington, MN 55437 Rochester, MN 55901
Phone: [phone] Phone: [phone]
Phone: [phone] Phone: [phone]
Fax: [phone] Fax: [phone]
Web site: http://www.watersnet.com

Waters Network Systems MS1008-2G-4POE/PSX1008-2G-4PoE User’s Manual Page 2
Table of Contents
1.0 Specifications......................................................................................................5
2.0 Package Contents ...............................................................................................8
3.0 Introduction..........................................................................................................8
3.1 Switch Features...................................................................................................10
3.2 Software Features...............................................................................................12
3.3 Management Methods.........................................................................................14
3.3.1 Console and Telnet Management....................................................................15
3.3.2 Web-based Management.................................................................................15
3.3.3 SNMP Network Management...........................................................................15
3.4 Hardware Description..........................................................................................15
3.5 LED Indicators.....................................................................................................17
3.6 Desktop Installation.............................................................................................17
3.6.1 Attaching Rubber Feet.....................................................................................18
3.6.2 Power On.........................................................................................................18
4.0 Network Applications........................................................................................18
4.1 Network Configuration.........................................................................................20
5.0 Web Based Management ..................................................................................23
5.1 Workstation Settings for Web Management ........................................................23
5.2 Login via the Web................................................................................................23
5.3 System Information..............................................................................................24
5.4 IP Configuration...................................................................................................25
5.5 DHCP Server.......................................................................................................26
5.5.1 DHCP Server Configuration.............................................................................26
5.6 Port and IP Bindings............................................................................................28
5.7 TFTP Transaction................................................................................................28
5.8 Restore Configuration..........................................................................................29
5.9 Backup Configuration..........................................................................................29

Waters Network Systems MS1008-2G-4POE/PSX1008-2G-4PoE User’s Manual Page 3
5.10 System Event Log Menu .....................................................................................30
5.11 SMTP Configuration.........................................................................................31
5.12 Event Configuration.............................................................................................32
5.13 SNTP Configuration.............................................................................................34
5.14 IP Security .........................................................................................................37
5.15 User Authentication.............................................................................................38
5.16 Port Menu............................................................................................................38
5.17 Port Control Menu ...............................................................................................39
5.18 Port Trunking.......................................................................................................41
5.19 State Activity........................................................................................................43
5.20 Port Mirroring.......................................................................................................43
5.21 Rate Limiting........................................................................................................45
5.22 Protocol Menu Options......................................................................................46
5.22.1 VLANs..............................................................................................................46
5.22.2 Port Based VLAN Configuration.....................................................................46
5.22.3 802.1q VLAN..................................................................................................48
5.23 RSTP (Rapid Spanning Tree Protocol) Menu......................................................51
5.23.1 RSTP Configuration.......................................................................................51
5.23.2 Port Configuration ........................................................................................53
5.24 SNMP Configuration..........................................................................................54
5.24.1 System Configuration Menu...........................................................................54
5.24.2 Trap Configuration .........................................................................................55
5.24.3 SNMPV3 Configuration..................................................................................56
5.25 QoS Configuration...............................................................................................59
5.26 IGMP Configuration...........................................................................................61
5.27 X-ring...................................................................................................................62
5.28 Security Menu....................................................................................................64
5.29 MAC Address Table.............................................................................................67
5.30 Power over Ethernet (PoE)..................................................................................70

Waters Network Systems MS1008-2G-4POE/PSX1008-2G-4PoE User’s Manual Page 4
5.31 Factory Default Settings......................................................................................71
5.32 Save Configuration..............................................................................................72
5.33 Reboot the System..............................................................................................72
6.0 CLI Commands..................................................................................................73
7.0 Troubleshooting................................................................................................95
7.1 Before Calling for Assistance...............................................................................95
7.2 Return Material Authorization (RMA) Procedure .................................................96
7.3 Shipping and Packaging Information...................................................................97
8.0 Warranty.............................................................................................................98

Waters Network Systems MS1008-2G-4POE/PSX1008-2G-4PoE User’s Manual Page 5
1.0 Specifications
OPERATIONAL CHARACTERISTICS:
MAC Address Table: 8k
Switching Mode: Store-and-forward
Bandwidth: Up to 18Gbps
System Throughput: Up to 26.7Mbps (64bytes packet length)
Memory Buffer Size: 1Mb
Performance: Non-blocking wire speed
MANAGEMENT FEATURES:
Web-based, Telnet and console
SNMP
SNMP IP security (supports 4 IP accounts)
RMON
Port setting for duplex and speed
Port trunking (3 groups)
Port based and tagged VLANs (up to 256)
QoS
IGMP (Supports 256 IGMP groups and IGMP query)
GVRP (256 groups)
Port security
Port mirroring
Broadcast storm
Spanning Tree
SMTP
System Log
DHCP
SNTP
NETWORK STANDARDS:
IEEE 802.3
IEEE 802.3u
IEEE 802.3z
IEEE 802.3x
IEEE 802.3ab
IEEE 802.3ad
IEEE 802.1d
IEEE 802.1s

Waters Network Systems MS1008-2G-4POE/PSX1008-2G-4PoE User’s Manual Page 6
IEEE 802.1w
IEEE 802.1d
IEEE 802.1p
IEEE 802.1q
IEEE 802.1x
EMI/SAFETY COMPLIANCE:
FCC Class A, CE, UL cUL, CE/EN60950
NETWORK CABLE CONNECTORS
RJ45 shielded female ports
10/100Mbps: CAT5 UTP or better
Multimode: LC
Singlemode: LC
POWER SUPPLY:
Input Voltage
90 to 240 VAC, 50 to 60Hz
Power Consumption
10 watts maximum
OPERATING ENVIRONMENT:
Ambient Temperature:
32° to 140°F (0° to 60°C)
Storage:
14° to 158°F (-10°to 70°C)
Ambient relative humidity:
5% to 90% (non-condensing)
MECHANICAL:
Enclosure:
Rugged high-strength sheet metal suitable for stand-alone, wall or tabletop
mounting
Cooling Method: Internal fan
PHYSICAL CHARACTERISTICS:

Waters Network Systems MS1008-2G-4POE/PSX1008-2G-4PoE User’s Manual Page 7
GSM2109:
Dimensions:
8.5 x 5.5 x 1.75 in (216 x 140 x 45mm)
Weight:
2 lbs (.91kg)
GSM1009-1SFP:
Dimensions:
11 x 10.5 x 2 in (279 x 267 x 51mm)
Weight:
3.7lbs (1.68kg)
Warranty:
Limited Lifetime

Waters Network Systems MS1008-2G-4POE/PSX1008-2G-4PoE User’s Manual Page 8
2.0 Package Contents
Examine the shipping container for obvious damage prior to installing this product.
Notify the carrier of any damage that you believe occurred during shipment. Ensure
that the items listed below are included. If an item is missing, please contact your
supplier. Both the MS1008-2G-4PoE and PSX1008-2G-4PoE switch package
contains the following:
Switch
Power Cord
Four Rubber Feet
RS-232 cable
User’s Guide
3.0 Introduction
In our modern society, communication and sharing information is essential to our lives.
Computer networks have proven to be one of the fastest methods of communication.
The switch is a compact desktop size switch that is an ideal solution for any network user.
The switch provides high-performance managed switching functions with low-cost
connectivity. The switch features store-and-forward switching and will auto-learn and
store source addresses with an 8K-entry MAC address table.
Figure 3.1 - PSX1008-2G-4PoE switch
The switch provides eight switched auto-sensing 10/100Base-TX RJ45 ports plus one
mini GBIC and one 10/100/1000Base-TX port. The switch provides nine usable ports.

Waters Network Systems MS1008-2G-4POE/PSX1008-2G-4PoE User’s Manual Page 9
The ninth port can be used for 1000Base-SX fiber connectivity or for
10/100/1000Base-TX connectivity.
Four of the 10/100Base-TX ports provide Power over Ethernet (PoE) connectivity. The
PoE ports eliminates the need to run 110/220 VAC power to other devices on the LAN.
The same CAT5 Ethernet cable that carries data to each device can also deliver power
over the same cable. This allows greater flexibility in the location of network devices
and can help reduce installation costs.
There are two system components for PoE: the power sourcing equipment (PSE) which
initiates the connection to the second component--the powered device (PD). The current
is transmitted over two of the four twisted pairs of wires in a CAT5 cable.
The PoE ports follow the IEEE 802.3af standard and are completely compatible with
existing Ethernet switches and networked devices. Because the PSE tests whether a
networked device is PoE-capable, power is never transmitted unless a PD is located at
other end of the cable. It also continues to monitor the channel. If the PD does not draw a
minimum current because it has been unplugged or physically turned off, the PSE shuts
down the power to that port. Optionally, the standard permits PDs to send a signal to
the PSEs for their power requirement.
The switch will automatically detect the speed of connected devices to accommodate 10,
100, 1000Mbps on the RJ45 ports. All RJ45 ports support the Auto MDI/MDIX function.
With the built-in Web-based management functionality, managing and configuring the
switch is easy. From cabinet management to port-level control and monitoring, you can
visually configure and manage your network via your Web Browser. The switch can be
managed via a web browser, Telnet, CLI (command line interface) commands or SNMP
Management.
Ethernet switching technology dramatically boosted the total bandwidth of a network,

Waters Network Systems MS1008-2G-4POE/PSX1008-2G-4PoE User’s Manual Page 10
eliminating congestion problems inherent with the carrier sense multiple access with the
collision detection (CSMA/CD) protocol and greatly reduced unnecessary transmissions.
This revolutionized networking. First, by allowing two-way, simultaneous transmissions
over the same port (full-duplex), bandwidth was essentially doubled. Second, by
reducing the collision domain to a single switch-port, the need for carrier sensing was
eliminated. Third, by using the store-and-forward technology’s approach of inspecting
each packet to intercept corrupt or redundant data, switching eliminated unnecessary
transmissions that slow down network traffic.
Auto-negotiation regulates the speed and duplex of each port, based on the capability of
both devices. Flow-control allows transmission from a 100Mbps node to a 10Mbps node
without loss of data. Auto-negotiation and flow-control may have to be disabled for some
networking operations that involve legacy equipment. Disabling the auto-negotiation is
accomplished by hard setting the speed or duplex mode of a port.
3.1 Switch Features
8-port 10/100Base-TX RJ45 ports
One mini GBIC slot for SFP module for 1000Base-SX or LX fiber connectivity
or one 10/100/1000Base-TX port
Embedded 4-port PoE inject function
Conforms to IEEE 802.3, 802.3u, 802.3x, 802.3z, and 802.3ab Ethernet
Standards
Auto-sensing 10/100/1000Base-TX RJ45 port ports
Automatic MDI/MDIX crossover for each 10/100Base-TX port
Console port on front side for system configuration
Half-duplex mode for backpressure
Full-duplex for flow control
Store-and-forward switching architecture
Automatic address learning, address migration
8K-entry MAC address table

Waters Network Systems MS1008-2G-4POE/PSX1008-2G-4PoE User’s Manual Page 11
5.6Gbps switch bandwidth
IGMP snooping
GVRP function
802.1x user authentication
802.1p CoS per port 4 queues
Port based VLAN 802.1q VLAN
802.3ad port trunk with LACP
STP/RSTP
QoS
•Port based / tag based
•IPv4 Tos/Ipv4, Ipv6 DiffServe
Port mirror and bandwidth control
802.1x user authentication
GVRP and MVR function
Broadcast storm filter
DHCP client, relay, server
SNTP and SMTP
Management IP address security
MAC address security
System log
SNMP trap support
TFTP firmware update
Web/SNMP/Telnet/CLI//MenuDrivenRMON
Performs non-blocking full wire speed
Configuration upload and download
Supports X-ring function

Waters Network Systems MS1008-2G-4POE/PSX1008-2G-4PoE User’s Manual Page 12
3.2 Software Features
RFC Standard RFC2233 MIBII, RFC 1157 SNMP MIB, RFC 1493 Bridge
MIB, RFC 2674 VLAN MIB, RFC 2665 Ethernet like MIB,
RFC1215 Trap MIB, RFC 2819 RMON MIB, Private MIB,
RFC2030 SNTP, RFC 2821 SMTP, RFC 1757 RMON1 MIB,
RFC 1215 Trap
Management SNMP v1, SNMP v2c, SNMP v3, Telnet, Console (CLI), Web
management and menu driven
SNMP Trap Cold start, warm start, link down, link up, authorization fail,
Trap station up to 3.
Port Trunk Supports IEEE802.3ad with LACP function. Up to 3 trunk
groups and maximum group member up to 4 ports.
Class of Service Per port supports 4 queues. Weight round ratio (WRR): High:
Mid-High: Mid-Low: Low (8:4:2:1)
QoS Port based, Tag based, IPv4 Type of service, Ipv6 Different
service.
VLAN Port based VLAN
Double Tag VLAN for management
IEEE802.1Q Tag VLAN.
Static VLAN groups up to 256
Dynamic VLAN groups up to 2048
VLAN ID can be assigned from 1 to 4094.
GVRP function supports 256 groups.
IGMP IGMP v1 and v2 compliance and also supports 256 IGMP
groups and support query mode.

Waters Network Systems MS1008-2G-4POE/PSX1008-2G-4PoE User’s Manual Page 13
Port Security Supports ingress and egress MAC address filter and static
source MAC address lock.
Port Mirror Global system supports 3 mirroring types: “RX, TX and Both
packet”. The maximum of port mirror entries is 8.
Bandwidth
Control
Ingress rate limiting packet type: all of frames, broadcast,
multicast, unknown unicast and broadcast packet.
Egress rate shaping supports all of packet.
Rate limiting levels: 64kbps to 64Mbits or up to 256Mbits for
Gigabit port.
User
Authentication
Support IEEE802.1x User-Authentication and can report to
RADIUS server.
Reject
Accept
Authorize
Disable
DHCP DHCP Client, DHCP relay and DHCP Server.
DHCP server provides global IP pool for DHCP server.
Packet filter Broadcast storm packet filter by 5%, 10%, 15% and 25%.
Port Security Supports ingress and egress MAC address filter and static
source MAC address lock
System log Provide 1000 log entries and supports remote storage
function.
SNMP IP
security
Supports 10 IP address accounts for system management
security for web, SNMP, Telnet to prevent intruders.
SMTP 6 mail accounts.
SNTP Supports RFC2030 simple network time protocol

Waters Network Systems MS1008-2G-4POE/PSX1008-2G-4PoE User’s Manual Page 14
Configuration
upload and
download
Support binary format configuration file for system quick
configuration.
Spanning Tree IEEE802.1d Spanning tree
IEEE802.1w Rapid spanning tree
X-ring
Provides X-ring, dual homing and coupling ring.
Provides redundant backup feature and recovery time below
300ms
PoE
management
PoE Enable/Disable; Power limit by classification: Enable/
Disable PD power classification and output power will be
limited by PD’s classification.
Power limit by management: Enable power feeding priority
Priority: Per port power feeding priority setting. Once current
power output is out of switch’s ability, power will be shut down.
Detect Legacy Signature: The goal of Detect Legacy
Signature is to identify these devices based on their unique
electrical signatures (resistive and capacitive) and power them
up as selectively as possible. Some of CISCO PD devices are
pre-standard and do not follow 802.3af with exactly electrical
signature. If that is the case, this function should be enabled.
Table 3.1 – Software Features
3.3 Management Methods
The switch supports following management methods:
Console and Telnet Management
Web-based Management
SNMP Network Management

Waters Network Systems MS1008-2G-4POE/PSX1008-2G-4PoE User’s Manual Page 15
3.3.1 Console and Telnet Management
Console Management is done through the RS-232 Console Port. Use the RS-232 cable
supplied in your package to connect directly to a workstation from your switch. Use the
default IP 192.168.16.1 to use Telnet or Web Management to login to the switch and
modify the configuration.
3.3.2 Web-based Management
The switch provides an embedded HTML web site residing in flash memory. It offers
advanced management features and allow users to manage the switch from anywhere
on the network through a standard browser such as Microsoft Internet Explorer.
3.3.3 SNMP Network Management
SNMP (Simple Network Management Protocol) provides a means to monitor and control
network devices, manage configurations, collect statistics, performance and security
information.
3.4 Hardware Description
Front Panel
The front panel of the switch consists of eight auto-sensing 10/100Base-TX RJ45 (Ports
5-8 PoE ports) ports, one mini GBIC slot and one 10/100/1000Base-TX port. The ninth
10/100/1000Base-TX port shares the slot with the mini GBIC. So, if the GBIC is used,
the ninth 10/100/1000Bse-TX port is inactive. Therefore, the switch provides nine
usable ports. You have the choice of using the ninth port in copper or fiber. The LED
indicators are also located on the front panel of the switch.
The console connection is also on the front panel of the switch. The console port can
be used to perform management functions. Console connection requires a direct
connection between the switch and a workstation with a RS-232 cable.

Waters Network Systems MS1008-2G-4POE/PSX1008-2G-4PoE User’s Manual Page 16
Figure 3.2 - Front Panel
Rear Panel
A three-pronged AC power plug is located on the rear panel of the switch. The switch
operates in the range 100-240V AC, 50-60Hz.
Figure 3.3 - Rear Panel
Hardware Ports
One slot for mini GBIC
One 10/100/1000Base-TX port
Eight 10/100Base-TX connections. MDI allows you to connect to another
hub or switch and MDIX allows you to connect to a workstation or PC.
Therefore, Auto MDI/MDIX means that you can connect to another switch or
workstation without a crossover cable.

Waters Network Systems MS1008-2G-4POE/PSX1008-2G-4PoE User’s Manual Page 17
3.5 LED Indicators
The following table provides the status and description of the LEDs. The LEDs provide a
real-time indication of systematic operation status.
LED Status Color Description
Power On Green Power On
On Green The port is operating at 1000Mbps.
On Orange The port is operating at 100Mbps
1000M
(Port 9) Off No device attached
On Green
The port is supplying power to the powered
device.
FWD
(Ports
5-8) Off No powered device is attached or power failed.
On Green The port is operating at 100Mbps.100M
(Ports
1-9) Off No device attached.
On Green The port is connecting with the device.
Blinks Green The port is receiving or transmitting data.
LNK/
ACT Off No device attached.
On Orange The port is operating in full-duplex mode.
Blinks Green Packet collisions occurring.
FDX/
COL Off The port is operating in half-duplex mode.
Table 3.2 - LED Description
3.6 Desktop Installation
Choose a surface for your switch that is clean, smooth, level, sturdy and with a power
outlet nearby. Make sure there is enough clearance around the switch to allow
attachment of cables, power cord and air circulation.

Waters Network Systems MS1008-2G-4POE/PSX1008-2G-4PoE User’s Manual Page 18
3.6.1 Attaching Rubber Feet
1. Make sure the mounting surface on the bottom of the switch is free of grease and
dust.
2. Remove adhesive backing from the rubber feet.
3. Apply the rubber feet to each corner on the bottom of the switch.
3.6.2 Power On
Connect the power cord to the AC power socket on the rear panel of the switch. Check
the power indicator on the front panel to see if power is properly supplied.
4.0 Network Applications
This section provides samples of network topology in which the GSM2109/1009 switch
can be used. This model switch is generally used as a desktop, workgroup or edge
segment switch.
Desktop Application
The switch provides an ideal solution for small workgroups. The switch can be used as a
standalone switch to which personal computers, servers, and print servers are directly
connected to form a small workgroup.
Figure 4.1 – Workgroup/Classroom Application

Waters Network Systems MS1008-2G-4POE/PSX1008-2G-4PoE User’s Manual Page 19
Segment Application
For enterprise networks where large data packets are constantly processed, this switch
is suitable for department users to connect to the corporate backbone. The switch
automatically learns node addresses, which are subsequently used to filter and forward
all traffic based on the destination address. You can use any of the copper ports or the
mini GBIC port to connect with another switch to interconnect each of your
small-switched workgroups to form a larger switched network.
Figure 4.2 – Segment Application

Waters Network Systems MS1008-2G-4POE/PSX1008-2G-4PoE User’s Manual Page 20
PoE
The four-port PoE switch provides power to the powered devices that follow the IEEE
802.3af standard on the network. The following figure provides an example of a network
application for PoE.
Figure 4.3 – PoE Switch with Wireless Powered Device
4.1 Network Configuration
This section explains how to configure console management via a direct connection to
the console port of the switch. Console management involves the administration of the
switch via a direct connection to the RS-232 console port. This port is a female DB-9
connector. From the Main Console Management Menu, you have access to all of the
management functions of the switch.