Watersnake ASP T18-SW User manual

ASP T18SW (55043)
ASP T24SW (55199)
Watersnake Asp Transom Motor User Manual (Ver.3)
ASP TRANSOM
MOUNT
TRANSOM MOUNT ELECTRIC MOTOR
OWNERS MANUAL
Watersnake Asp Transom User Manual v3 2023-03-17.indd 1Watersnake Asp Transom User Manual v3 2023-03-17.indd 1 17/3/2023 4:36 pm17/3/2023 4:36 pm

WELCOME TO WATERSNAKE
Congratulations and welcome to a world of silent motoring.
Powerful yet silent, the Watersnake electric motors are built to suit all angling
conditions. High quality materials, superior design and precision engineering
make these motors long-wearing and reliable.
IMPORTANT
Please read this manual completely before starting installation and using the
electric motor.
Disclaimer: The information provided in this Watersnake Motor Manual is correct at time of printing.
For the most up to date information, check for the latest version on our website at
https://www.watersnake.com.au/pages/watersnake-user-manuals
BEFORE YOU BEGIN:
Trolling motors are high-current devices that require an ideal power supply.
Follow these steps to avoid problems:
12V DEEP CYCLE
OR 12V LIFEPO4
BATTERIES ONLY
MORE INFO ON PAGE 7
EXTENDING THE
BATTERY CABLES?
IMPORTANT INFO ON PAGE 9
BATTERY CAN BE
CHARGED WHILE USING THE
MOTOR ONLY IF VOLTAGE
INPUT TO THE MOTOR IS
EQUAL OR LESS THAN 14.5V
MORE INFO ON PAGE 9
USE AN
INLINE FUSE OR
CIRCUIT BREAKER
(NOT INCLUDED)
MORE INFO ON PAGE 8
2
5
1
34
SUGGESTED BATTERY SIZE:
MOTOR SIZE BATTERY SIZE
18LB  24LB 40AH OR LARGER
34LB 60AH OR LARGER
44LB 80AH OR LARGER
54LB  65LB 100AH OR LARGER
Watersnake Asp Transom User Manual v3 2023-03-17.indd 2Watersnake Asp Transom User Manual v3 2023-03-17.indd 2 17/3/2023 4:36 pm17/3/2023 4:36 pm

www.watersnake.com.au 3
KNOW YOUR BOAT...............................................................................4
FEATURES OF YOUR MOTOR...............................................................5
INSTALLATION
PRE INSTALLATION CHECKLIST........................................................6
BATTERY AND POWER........................................................................7
Best practices and battery type ........................................................7
Inline fuse or circuit breaker ............................................................8
Extending battery leads ....................................................................9
Battery charging ...............................................................................9
Connecting your motor to the battery ..............................................10
ATTACHING THE PROPELLER.............................................................11
ATTACHING THE MOTOR TO YOUR BOAT ............................................12
USING THE MOTOR
PRE USE CHECKLIST..........................................................................12
TILTING YOUR T24 ASP MOTOR .........................................................12
DEPTH ADJUSTMENT .........................................................................13
STEERING COUNTERFORCE.............................................................13
HEAD UNIT AND SPEED CONTROL ....................................................14
RECOMMENDATIONS WHEN USING YOUR MOTOR...........................15
AFTER EVERY USE..............................................................................15
MOTOR MAINTENANCE AND STORAGE.............................................16
TROUBLESHOOTING............................................................................17
OPTIONAL ACCESSORIES ...................................................................18
MOTOR SPECIFICATIONS ....................................................................19
MOTOR SCHEMATICS AND PARTS LISTS ...........................................20
CONTENTS
Watersnake Asp Transom User Manual v3 2023-03-17.indd 3Watersnake Asp Transom User Manual v3 2023-03-17.indd 3 17/3/2023 4:36 pm17/3/2023 4:36 pm

4Watersnake Asp Transom Motor User Manual (Ver.3)
KNOW YOUR BOAT
Keel
Bow
Port
Stern
Starboard Gunwale
Bow Stern
Hull
Gunwale
Port Starboard
Inboard
Outboard
Stern / Transom
Watersnake Asp Transom User Manual v3 2023-03-17.indd 4Watersnake Asp Transom User Manual v3 2023-03-17.indd 4 17/3/2023 4:36 pm17/3/2023 4:36 pm

www.watersnake.com.au 5
FEATURES OF YOUR MOTOR
PLEASE NOTE: Specifications are subject to change without notice. Diagram
of motor is for reference only and may be different from your actual motor.
Please note: the ASP T18 model
does not have a tilting feature.
Head Unit Retractable
Tiller handle
Retractable
Tiller handle
Handle lock /
release pin
Handle lock /
release pin
Nylon
bracket
Weedless
two-blade
propeller
Motor unit
Depth collar
height adjustment
Steering Counter-
Force adjustment
Impact-protection
release clamp
ASP T24ASP T18
Head Unit
Tilt lock /
release pin
Tilting
nylon
bracket
Weedless
two-blade
propeller
Motor unit
Depth collar
height adjustment
Steering Counter-
Force adjustment
Watersnake Asp Transom User Manual v3 2023-03-17.indd 5Watersnake Asp Transom User Manual v3 2023-03-17.indd 5 17/3/2023 4:36 pm17/3/2023 4:36 pm

6Watersnake Asp Transom Motor User Manual (Ver.3)
PRE INSTALLATION CHECKLIST
1. Familiarise yourself with the user manual and the various parts of your
Watersnake motor.
2. Select desired mounting location on boat/kayak.
3. 12V deep cycle or 12V LiFePO4 battery (your Watersnake motor IS NOT
designed for use with car / truck /motorcycle type batteries) – for more
information about appropriate batteries for your Watersnake motor, refer to
page 7.
4. Check battery cable length in relation to location of your 12v deep cycle or
12V LiFePO4 battery. If extension to battery cable is required, refer to table
on page 9. NOTE – if extending battery cable, ensure that the circuit breaker
remains in place on the positive wire.
PLEASE NOTE:
TERNARY LITHIUM BATTERIES MUST NOT BE USED WITH
THIS WATERSNAKE MOTOR. Refer to information on page 7.
THE BELOW INFORMATION IS FOR THE USA ONLY.
INSTALLATION
Watersnake Asp Transom User Manual v3 2023-03-17.indd 6Watersnake Asp Transom User Manual v3 2023-03-17.indd 6 17/3/2023 4:36 pm17/3/2023 4:36 pm

www.watersnake.com.au 7
BATTERY AND POWER
BATTERY TYPE
USE A  VOLT DEEP CYCLE OR A V LIFEPO BATTERY
12V DEEP CYCLE BATTERY
Deep-cycle batteries deliver sustained power with low current draw over
extended periods. They can be drained to low levels without developing a
“memory” and can be fully recharged hundreds of times over their working lives.
Do not use a standard car, truck or marine batteries (called a cranking battery).
They are designed to provide a pulse of “cranking power” over a short period,
can develop a “memory” preventing complete recharge and can produce current
surges that may damage sensitive electronic components on your Watersnake.
LITHIUM BATTERIES
BEST PRACTICES
INSTALLING AND CONNECTING YOUR MOTOR
1. Your Watersnake motor is designed to be powered by a 12v deep cycle or
LifePO4 battery that should output no more than 14.5v. If the voltage input
to your Watersnake motor exceeds 14.5v it may damage the sensitive
electronics and void your warranty. A dedicated battery system is preferable.
Do not connect other items like fish finders or lighting to the trolling motor
battery.If you are unsure about the voltage output of your battery, contact
your battery supplier or consult a marine auto electrician.
2. This Watersnake motor is compatible with a battery system that is being
charged by an alternator or solar system, so long as the voltage input to the
Watersnake motor does not exceed 14.5v whilst the battery is being charged.
3. Route the wiring from the battery to the trolling motor on an alternate route
or path to other wiring on the boat. If possible, it is preferable the wire is
fitted to the opposite side of the boat to other wiring.
4. If you have to extend the wiring to connect the motor please review
the extending battery leads section of the manual (page 9) so you fully
understand this process.
5. This trolling motor requires a circuit breaker or inline fuse to protect the
motor. See page 8 for more information.
CAUTION: Please read the following information before you
connect your electric motor to your baery.
TERNARY LITHIUM BATTERY WARNING
Ternary Lithium batteries must not be used with this Watersnake motor
as their voltage output is too high.
Watersnake Asp Transom User Manual v3 2023-03-17.indd 7Watersnake Asp Transom User Manual v3 2023-03-17.indd 7 17/3/2023 4:36 pm17/3/2023 4:36 pm

8Watersnake Asp Transom Motor User Manual (Ver.3)
INLINE FUSE OR CIRCUIT
BREAKER
An inline fuse or circuit breaker is required when connecting your Watersnake
Asp motor to the battery. This is a connection that joins the motor battery
cable to the battery and protects the motor by shutting off power in the event
of an overload or short circuit.
BATTERY AND POWER CONTINUED
SUGGESTED FUSE OR CIRCUIT BREAKER SIZE
Asp T18 20A
Asp T24 25A
CIRCUIT BREAKER
EXAMPLE
12V DEEP CYCLE OR LIFEPO4 LITHIUM BATTERY
12V LIFEPO4 LITHIUM BATTERY
Lithium Iron Phosphate (LiFePO4) is the safest lithium battery type. We
recommend doing your research on a LiFePO4 battery before purchasing to
make sure you are purchasing from a reputable company and the battery has a
maximum voltage output under 14.5V. There are many cheap lithium batteries
on the market that can be harmful to your Watersnake motor.
Watersnake Asp Transom User Manual v3 2023-03-17.indd 8Watersnake Asp Transom User Manual v3 2023-03-17.indd 8 17/3/2023 4:36 pm17/3/2023 4:36 pm

www.watersnake.com.au 9
EXTENDING BATTERY LEADS
The longer your battery cable needs to be, the thicker it needs to be to avoid
damaging voltage drop. The supplied cable has the correct wire gauge
(thickness) for its length. But if you need to extend the length by more than
30%, you will need to replace the existing cable completely with a new longer
thicker cable. This means the entire cable will be the correct wire gauge for
the new length. See below to find the correct wire gauge for your motor thrust
and required cable length. Only use twin-sheathed tinned cable.
Note: The above table is intended as a guide only. Your local electrical supplier will
be able to advise in greater detail based on your particular set up and requirements.
MOTOR MODEL
Asp T18
Asp T24
MAX AMP DRAW
15A
20A
WIRE EXTENSION LENGTH / WIRE GAUGE FOR ENTIRE CABLE
(American Wire Gauge - AWG) Note: Lower AWG# is thicker wire.
1 Metre / 12AWG 1-3 Metres / 10AWG 3-5 Metres / 10AWG
1 Metre / 12AWG 1-3 Metres / 10AWG 3-5 Metres / 8AWG
BATTERY CHARGING
Charging a battery while it is powering the motor will increase the voltage
delivered to the motor. This motor can be powered by a charging battery (e.g.
charging with an alternator or solar panels) as long as the voltage it receives
does not exceed 14.5 volts. Exceeding 14.5 volts will potentially damage
electrical components in the motor and is not covered by warranty.
When you are off the water and are charging your battery at home for long
periods of time via a 240v or 110v AC charger we recommend you disconnect
the motor from the battery.
AVOID USING STOREBOUGHT BATTERY
BOXES WITH BUILTIN CIRCUITRY
Battery Boxes use low quality electrical components that cannot handle the
high current loads that trolling motors draw. We recommend connecting your
Watersnake motor directly to a deep cycle or LiFePO4 battery using the provided
battery leads.
BATTERY BOX WITH
BUILT IN CIRCUITRY.
DO NOT USE!
SIMPLE BATTERY
BOX WITH NO
CONNECTIONS
OK TO USE!
Watersnake Asp Transom User Manual v3 2023-03-17.indd 9Watersnake Asp Transom User Manual v3 2023-03-17.indd 9 17/3/2023 4:36 pm17/3/2023 4:36 pm

10 Watersnake Asp Transom Motor User Manual (Ver.3)
All Watersnake wiring connections should conform to best marine standards.
Soldered, sealed and heat-shrink protected. If you doubt your ability to
produce quality waterproof connections or lack the equipment, consult a
marine technician or auto electrician.
• Your Watersnake comes factory-fitted with a standard length of twin flex
wiring with alligator clips to attach to the battery.
• Before connecting the motor’s cables to the battery terminals, ensure all
switches are in the OFF position and stand clear of the propeller.
• Connect the red cable to the positive (+) terminal and the black cable to the
negative (-) terminal, making sure the terminals are clean before doing so.
A clean connection will minimise power wastage and give you maximum
power from the battery.
• The voltage input must be 14.5V or lower. Voltage input above 14.5V will
damage the motor and void the warranty.
• If you intend to charge your battery via an alternator or solar panel, it is
important that the battery voltage output does not exceed 14.5v. If you are
unsure of the voltage your battery will output, consult a marine technician
or auto electrician.
CONNECTING YOUR MOTOR
TO THE BATTERY
Watersnake Asp Transom User Manual v3 2023-03-17.indd 10Watersnake Asp Transom User Manual v3 2023-03-17.indd 10 17/3/2023 4:36 pm17/3/2023 4:36 pm

www.watersnake.com.au 11
1. Place the Shear Pin in the hole of the Propeller Shaft as shown below.
2. Note on the inside of the Propeller there is a groove for the Shear Pin to
slot into. Place the Propeller over just the end of the Propeller Shaft, then
rotate the propeller to align the groove to the Shear Pin. Push the Prop
fully onto the Shaft, making sure the Pin sits in the groove.
3. While holding the Propeller, tighten the Propeller Nut firmly with the
provided tool.
ATTACHING THE PROPELLER
1
2
3
WARNING: Before doing anything with the propeller, ensure
the cables from the electric motor to the battery are disconnected.
Propeller Nut
Propeller
Tool to tighten the
Propeller Nut.
Propeller Shaft
Shear pin
Watersnake Asp Transom User Manual v3 2023-03-17.indd 11Watersnake Asp Transom User Manual v3 2023-03-17.indd 11 17/3/2023 4:36 pm17/3/2023 4:36 pm

12 Watersnake Asp Transom Motor User Manual (Ver.3)
ATTACHING THE MOTOR
TO YOUR BOAT
• Ensure that your Watersnake motor is securely attached to your boat.
• Fully charged 12v deep cycle or 12V LiFePO4 battery (your Watersnake
motor is not designed to be used with a car / truck / motorcycle type or
Ternary Lithium battery).
• Check battery cable for any signs of damage or exposed wiring.
• Check battery terminals for any signs of corrosion or debris.
• Check fuse assembly / circuit breaker – clean if any signs of corrosion or
debris. Replace fuse if necessary. ( If your motor is equiped with one. )
NOTE: Please ensure this Watersnake motor is not your only means of
propulsion. Please follow the marine safety guide lines set by your state or
country of use.
PLEASE NOTE: Watersnake Distribution Pty Ltd accepts no liability for personal injury
or property damage caused while mounting, deploying or stowing this motor.
Place the motor’s mounting bracket over the
centre of your boat’s transom or your chosen
mounting position on your kayak. Tighten both
mounting bolts securely while taking care not to
over-tighten. (A) Note: if the motor is on the side
of your kayak, position it as close as possible to
the kayak hull. This minimises unwanted turning.
TILTING THE ASP T24 MOTOR: The Asp T24
model has a bracket that can adjust the
angle of the the motor. To adjust the motor
angle, hold the motor head with one hand
and depress the positioning pin at the top of
the mounting bracket with your other hand.
While pressing the positioning pin, move the
motor to your desired angle. Release the pin
and ensure the tilting mechanism locks in
securely. (B) Note: The Asp T18 model does
not have a tilt function.
USING THE MOTOR
PREUSE CHECKLIST  CHECK BEFORE EACH USE
BATTERY CHARGING
Please refer to battery charging section on page 9.
(A)
(B)
Watersnake Asp Transom User Manual v3 2023-03-17.indd 12Watersnake Asp Transom User Manual v3 2023-03-17.indd 12 17/3/2023 4:36 pm17/3/2023 4:36 pm

www.watersnake.com.au 13
CAUTION: Please keep you fingers and hands away from all
hinge points and the propeller at all times.
(A)
(A)
(B)
(B)
DEPTH ADJUSTMENT
The depth of the motor in the water can be adjusted. Hold the motor shaft with
one hand, loosen the Depth Collar Adjustment Screw and set the motor to the
desired depth, then retighten the adjusting screw of the depth collar securely (A).
The motor should be just deep enough in the water so air does not get sucked
down to the propeller during operation (called ventilation). This reduces the
motor efficiency.
STEERING COUNTER-FORCE
The motor is steered by pivoting the Tiller Handle side-to-side. You can fine-tune
the steering counter-force so the motor will stay in the direction you are aiming
without the need for continual correction:
Adjust the amount of steering counter-force by loosening or tightening the
counter-force bolt so it is just tight enough to maintain the same direction (B).
Depth collar
height adjustment
Depth collar
height adjustment
Steering Counter-
Force adjustment
Steering counter
force adjustment
ASP T24 TILTING BRACKET
ASP T18 BRACKET
STOWING
When your
Watersnake
motor is not
in use always
stow and store
it properly.
Watersnake Asp Transom User Manual v3 2023-03-17.indd 13Watersnake Asp Transom User Manual v3 2023-03-17.indd 13 17/3/2023 4:36 pm17/3/2023 4:36 pm

14 Watersnake Asp Transom Motor User Manual (Ver.3)
HEAD UNIT & SPEED CONTROL
The Head Unit controls are easy to use. There is a switch for Forward, Off and
Reverse ( I o R ) and a switch for Low (-) or High speeds (=).
Pull the button
and the handle
will extend
automatically.
Pull the
button and
push the
handle in.
The Tiller Handle on the motor head is stowable and extends with the pull of a
button. This makes the motor more compact and easier to store away
when not in use.
Low and High
speed switch
Forward / Off /
Reverse switch
Watersnake Asp Transom User Manual v3 2023-03-17.indd 14Watersnake Asp Transom User Manual v3 2023-03-17.indd 14 17/3/2023 4:36 pm17/3/2023 4:36 pm

www.watersnake.com.au 15
RECOMMENDATIONS
WHEN USING YOUR WATERSNAKE MOTOR
IN THE WATER
Upon connecting your battery to your motor, and before setting off in your boat,
make sure that your trolling motor is mounted correctly and stowed securely.
Of course once you engage your Watersnake motor for use make sure that it
is in the right place, not too low or too high. Once you are in deep water, you
should make sure that you gradually increase the speed of your trolling motor,
do not accelerate it up to full speed right away. It is recommended not to run
your trolling motor out of water for long periods of time.
AFTER EVERY USE
• Disconnect the motor from the battery.
• Recharge the battery as soon as possible.
• DO NOT PRESSURE WASH, EVEN AFTER FRESHWATER USE.
• Wipe your motor down with a wet rag. Concentrate on areas where salt, dirt
and weed fragments are likely to lodge – propeller, motor housing, alloy
shaft, depth collar and exposed parts of the mount assembly.
• Wipe these areas with a cloth soaked in warm soapy water and allow to dry.
• Apply a light coating of a non-staining silicone, petroleum-based or lanolin
spray to protect and lubricate exposed parts. Wipe over with a soft, dry
cloth.
• Store your Watersnake motor DISCONNECTED from its battery.
• If the boat is stored outdoors, remove the Watersnake motor and store
securely indoors in a cool, dry place.
• If the Watersnake motor is permanently mounted to the boat outdoors,
consider protecting it from harsh sunlight and the elements with a tarpaulin
or other cover.
Watersnake Asp Transom User Manual v3 2023-03-17.indd 15Watersnake Asp Transom User Manual v3 2023-03-17.indd 15 17/3/2023 4:36 pm17/3/2023 4:36 pm

16 Watersnake Asp Transom Motor User Manual (Ver.3)
MAINTENANCE PERIODICALLY DURING THE SEASON
• Disconnect motor from battery. Inspect battery terminals and cables for
signs of corrosion. Remove buildup with a small wire brush and treat with
anti-corrosion spray.
END OF SEASON, LONGTERM STORAGE
• Disconnect motor from battery.
• Inspect battery terminals and cables for signs of corrosion. Remove buildup
with a wire brush and treat with anti-corrosion spray.
• Remove motor from boat and store in a cool, dry place away from
temperature extremes.
MAINTENANCE
Watersnake Asp Transom User Manual v3 2023-03-17.indd 16Watersnake Asp Transom User Manual v3 2023-03-17.indd 16 17/3/2023 4:36 pm17/3/2023 4:36 pm

www.watersnake.com.au 17
TROUBLESHOOTING
QUICK REFERENCE GUIDE
A significant number of issues can be caused by a disruption of power supplied
to your Watersnake motor. Careful inspection of your 12v deep cycle battery,
wiring and fuse / circuit breaker set up should be completed before assuming
that there is a fault with your motor.
NO POWER / REDUCED POWER
• Check that battery connection has not been reversed (reversed polarity).
• Check that your 12v deep cycle or LiFePO4 battery is fully charged (+ 12v).
• Check terminals / connections are secure and not loose.
• Check terminals / connections / fuse or circuit breaker for any signs of
damage, corrosion or build up of debris.
• If the battery cable has been extended but not replaced, you may be
experiencing damaging voltage drop. Check the table on page 9 to see if you
have the correct gauge wire for the length of cable extension.
• With the battery disconnected remove propeller and check for any build up
of fishing line / weed or any other debris.
• With the battery disconnected check that propeller pin (shear pin) is in
place.
• Armature or magnet cracked or dislodged – grinding noise will come from
motor (Contact the Watersnake distributor in your region.)
NOISE OR VIBRATION COMING FROM MOTOR
• With the battery disconnected check that propeller is securely tightened and
shear pin is in place. Remove propeller and check for any build-up of fishing
line / weed or any other debris. Rotate the propeller 180º and then recheck
for vibration.
• Check that your 12v deep cycle or LiFePO4 battery is fully charged (+ 12v).
STILL HAVING MOTOR ISSUES?
More information like wiring diagrams,
spare parts and motor repair videos can
be found on our Watersnake motor
support webpage:
https://www.watersnake.com.au/pages/electric-motor-servicing
For more help you can also contact the Watersnake distributor for your region.
( Please see the back cover. )
Scan the QR
code to go to
the Watersnake
support page.
Watersnake Asp Transom User Manual v3 2023-03-17.indd 17Watersnake Asp Transom User Manual v3 2023-03-17.indd 17 17/3/2023 4:36 pm17/3/2023 4:36 pm

18 Watersnake Asp Transom Motor User Manual (Ver.3)
Watersnake
Propeller Kits
contain a propeller,
nut and shear pin.
It is recommended
you keep a spare
propeller on your
boat at all times.
WATERSNAKE MOTOR ACCESSORIES
SOLD SEPARATELY
SEE YOU NEAREST DEALER FOR MORE INFORMATION

Watersnake Two-Blade Mini Propeller
Replacement (18lb, 24lb)
PLEASE NOTE:
Spare parts may not be available in all areas. Please check with your local stockist.
Online ordering available please see back page for details.

Lower Motor Unit
Brush Kit for Asp
(18lb & 24lb)
Contents:
2 Springs.
2 Brushes
2 Holders
2 Screws
Watersnake Asp Transom User Manual v3 2023-03-17.indd 18Watersnake Asp Transom User Manual v3 2023-03-17.indd 18 17/3/2023 4:36 pm17/3/2023 4:36 pm

www.watersnake.com.au 19
MOTOR SPECIFICATIONS
* NOTE - this is to be used as a guide only. Check with your battery supplier
to confirm required size of 12 volt Deep Cycle or LiFePO4 battery that will be
appropriate for your situation.
MODEL CODE: 55043 NAME: ASP T18-SW ( White Saltwater )
VOLTAGE (V) 12v
MAX.THRUST (LB) 18lb
SHAFT LENGTH (IN) 24"
MIN. / MAX. AMP DRAW (A) MIN.7A MAX.15A
MAX. PROP RPM (NO LOAD) 1400rpm
SPEEDS 2 FORWARD AND 2 REVERSE
PROPELLER 2 BLADE
MOUNTING BRACKET NON-TILTING TRANSOM
REQUIRED BATTERY 12v DEEP CYCLE or LiFePO4
RECOMMENDED BATTERY SIZE (AH) 40 AMP HOUR OR LARGER*
BATTERY CABLE GAUGE 14AWG
MOTOR WEIGHT 2.35kg
MODEL CODE: 55199 NAME: ASP T24-SW ( White Saltwater )
VOLTAGE (V) 12v
MAX.THRUST (LB) 24lb
SHAFT LENGTH (IN) 24"
MIN. / MAX. AMP DRAW (A) MIN.9A MAX.20A
MAX. PROP RPM (NO LOAD) 1700rpm
SPEEDS 2 FORWARD AND 2 REVERSE
PROPELLER 2 BLADE
MOUNTING BRACKET TILTING TRANSOM
REQUIRED BATTERY 12V DEEP CYCLE or LiFePO4
RECOMMENDED BATTERY SIZE (AH) 40 AMP HOUR OR LARGER*
BATTERY CABLE GAUGE 14AWG
MOTOR WEIGHT 3.1kg
Watersnake Asp Transom User Manual v3 2023-03-17.indd 19Watersnake Asp Transom User Manual v3 2023-03-17.indd 19 17/3/2023 4:36 pm17/3/2023 4:36 pm

20 Watersnake Asp Transom Motor User Manual (Ver.3)
SCHEMATIC  PARTS LIST  ASP TSW
Part No.
Watersnake Asp Transom User Manual v3 2023-03-17.indd 20Watersnake Asp Transom User Manual v3 2023-03-17.indd 20 17/3/2023 4:36 pm17/3/2023 4:36 pm