We MS200 Assembly instructions

ENGLISH
BASIC OPERATION GUIDE
MS200
MulScreen Appliances
MS200
ENGLISH 4
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131 hp://www.dtresearch.com I hp://signage.dtri.com
Copyright © 2011, DT Research, Inc. All Rights Reserved. DT Research, WebDT are registered trademark of DT Research, Inc.
INTRODUCTION
Thank you for acquiring the MS200, part of the WebDT MulScreen
Appliance line by DT Research. The MS200 facilitates the creaon of a unique and powerful
communicaons medium that offers unparalleled opportunies to capture an audience’s aenon
at key decision-making locaons. The WebDT MulScreen Appliances enable efficient deployments
for digital signage, with reliable hardware features and innovave server-based soware. The
Microso® Windows® Embedded Standard 7 based MS200 offers remote management of the
devices and the displayed content with the WebDT Content Manager. The MS200 together with the
WebDT soware suite offers an effecve soluon for delivering and managing messages that target
audiences in the right place, at the right me.
Package Contents
One WebDT MS200 MulScreen Appliance1.
One security USB dongle2.
One power cord3.
One WebDT Content Manager CD4.
One image recovery DVD5.
WebDT Content Manager Insert including6. network connecon guide and important FAQ
WebDT MS200 Release Note 4.07.
Basic operaon guide8.
NOTE: The actual package contents may vary depending
on the configuraon acquired.
1
2
3
4
Content Manager Soware
SPECIFICATIONS
System
CPU Intel® Core™ i3, 2.93GHz; upgrade opon: Intel® Core™ i5
RAM 4GB DDR3
Storage 250GB HDD
Operang System Microso® Windows® Embedded Standard 7
Display Resoluon
2160 x 1920 for 1 x 2 digital signage array or
3840 x 1080 for 2 x 1 digital signage array
(max. DVI/ HDMI resoluon 1920 x 1080 per display)
Video Resoluon Full-HD/ Dual Full-HD
Network Interface 10/ 100/ 1000Mb BaseT LAN; Wi-Fi 802.11a/b/g (oponal)
Soware Compability Compable with WebDT Content Manager (WCM 4.0 SP1 or
above recommended)
Input/Output Ports
1 DVI-I; 1 HDMI; 8 Audio jacks; 8 USB 2.0 ports; 1 RJ45
connector for Ethernet; 1 IEEE 1394 port;
oponal WLAN (via internal PCI-Express slot or external USB)
Power
Power Supply 200W ATX
Mechanical
Enclosure Aluminum + steel
Dimensions (H x W x D) 4.09 x 10.4 x 13.3 in/ 104 x 265 x 338 mm
Weight 8.7 lbs/ 3.94 kg
Environmental
Temperature Operaon: 0°C - 40°C; Storage: -20°C - 60°C
Humidity 5% - 95% non-condensing
* Specificaons subject to change without noce.
BOG012011MS200ENG

Audio jacks USB ports Power buon HDD status indicator
RJ45 connector DVI-I output HDMI port IEEE 1394 port
MS200
ENGLISH 23ENGLISH
Memory and Storage
Depending on the base soware configuraon, the user may need only the internal HDD of the
MS200 for user’s installed soware and storage. The user may also supplement storage space with
USB-based peripherals such as flash disks, disk drives, etc.
I/O Ports
Connecng Peripherals
Insert the USB dongle to a USB port (1) and make sure your monitors are connected the MS200
with video cables (2). Aer the peripherals are well connected, plug the power cord into the
MS200 (3) and insert the other end into a power outlet.
NOTE: DO NOT connect the power cord before connecng the USB dongle and all cables to the MS200.
Powering ON and OFF
The Power Buon is located on the front of the MS200. To turn the MS200 on, push and release
the Power Buon on the front bezel. The power LED will be lit (blue), and the corresponding
interface will be shown on the display monitors.
To turn offthe device, use the soware shutdown interface provided, or unplug the appliance.
In the event of system lockup, unplug or re-plug the power cable. Also, the Power Buon may be
used to perform a reset on the device. To do that, push and hold the Power Buon for at least
4 seconds. The system will shut down and all unsaved work may be lost. Pushing on the Power
Buon again will restart the device.
Server Installaon
Please refer to the other documents inserted in the package to
start seng up your WebDT Content Manager server via the
WebDT Content Manager CD.
Appliance Registraon
Aer turning on the MS200 for the first me, a screen prompt is
displayed for registering the player. If the screen prompt is not
shown, please follow the instrucons below:
Press and hold “Control + Shi+ Space”to exit the WCM Player soware.1.
Navigate to Start | All Programs | DT Research | WebDT Signage Player2.
Select Register WebDT Signage Player Again. The Player Registraon screen should appear. Fill in3.
all fields to register. The required informaon is marked.
Click OK to register and connect to the WebDT Signage Appliance Publish Server.4.
<1> <2> <3>
Insert the USB dongle. Connect video cables (DVI/ HDMI)
with monitors.
Connect the power cord.
E
A
D C
AB
B F G B H B A
A B C D
E F G H
MS200 Front
MS200 Rear