WeatherTRAK ET Pro3 2-Wire Reference guide
BASIC TASKS
TOUCHPAD
ACTIVATE
Access this controller from WeatherTRAK.net or
WeatherTRAK Mobile
• Call Customer Support at: 800.362.8774
• Fill out the activation form at: hydropoint.com/activate
SET CONTROLLER MODE
Controller On/Off, Shutdown, or Winterized
• Press button
• Use button to select desired function
• To clear Shutdown or Winterized, press
Button, then press to reset the status
ASSIGNING THE DECODER TO A STATION
Note: For a dual valve decoder, the stations will
be sequential.
1. Plug the decoder into the terminal located on the
mini-chassis board (figure 1)
2. Press
3. Press until displays
(screen 15)
4. Press or until displays
5. Press
6. Press . The controller reads the decoder and
assigns it to the next station in sequence. If you need
to change the station number, press or
7. Press to assign the decoder to the station shown
8. Press or to set the power level. Power levels for
each station can be adjusted independently. Note
that the power level defaults to Low
9. Press to configure the decoder
10. Label the decoder then unplug it from the Station
Program terminal
11. To assign the next decoder, press . To exit
ALERT MANAGEMENT
MOBILE APP
Go to the tab on the Controller Settings page.
WEB
Use Alerts Page, or Multi-Controller Alert Report from
weathertrak.net.
CONTROLLER
While at the controller, use the following process:
Press Button. The first screen is the
showing any alert or warning that exists
on your controller. Each two letter code is an
Alert Category. An or appear beneath any
category that has an alert present.
QUICK REFERENCE CARD
RED BLK BLK
BLK STATION PROGRAM
RED RED
04012019
Flow Alerts — Issue with flow hardware or flow
feature programming. Fix the issue, then press
button to clear alert then retest
Valve Alerts — Issue with valve electrical
components or connections. Fix the issue, then
press button to clear alert then retest
Communication Alerts — Reset GPRS Status or
call Customer Service for assistance
Water Window Warning — Calculated irrigation
schedule exceeds the allowable irrigation time
programmed Water Window
Water Day Warning — Calculated irrigation
schedule exceeds number of allowable Water Days
programmed in Water Day Mode
Station High Depletion — Reset Station
Depletion from Manage Page of weathertrak.net or
from Help menu — “Help : 12 — Current Depletion”
Hardware Alert — Issue with controller hardware.
Call Customer Service for assistance
Subscription Alert — Call Customer Service to
update data service plan
:
:
:
:
:
:
:
:
QUICK REFERENCE CARD
Note: The controller
firmware may have been
update since installation.
If instructions don't match,
download the latest
Reference Card from
HydroPoint.com
Scan to view User Guide
RED BLK BLK BLK STATION PROGRAM
RED RED
24V PS MV1 MV2 MV3 MV4 VC VC VC VC FL1 FL2 FL3 FL4
FLOW
TROUBLESHOOTING
If you suspect that there is an issue with
your WeatherTRAK Controller hardware, we
have easy to use LED diagnostic lights on
the controller chassis.
Remove the controller panel from its
mounted to position to completely reveal
the controller chassis.
Use the chassis diagram above to identify each
of the eleven LED Diagnostic lights on the
chassis and check to see if each is illuminated.
Then, compare result to the diagnostic table and
take appropriate action.
Contact Customer Support with any questions:
Other WeatherTRAK Controllers manuals
Popular Controllers manuals by other brands
Clarke
Clarke CAT189 Operating & maintenance instructions
Becker
Becker WESTE 500 operating instructions
Nortech
Nortech CRC200+ Quick installation guide
Omron
Omron SYSMAC C200H CPU01-E installation guide
Lutron Electronics
Lutron Electronics GRAFIK Eye GRX-4M-GC Installer's guide
Kolin
Kolin KAG-75WCINV user manual
