Weber mt SRV 650 Operating instructions

SRV 650 1
OPERATING AND MAINTE-
NANCE MANUAL
Weber Maschinentechnik GmbH
Postfach 101465, 57326 Bad Laasphe-Rückershausen
Telephone + 49 27 54 / 398-0
Fax + 49 27 54 3 98-101 (switchboard) & 3 98-102 (spare parts)
SRV 650
Subaru- Robin ER 12
0612/englisch/Übersetzung der Original-Betriebsanleitung

2 SRV 650

SRV 650 3
Table of contents
Introduction 4
Safety guidelines 5
Graphic presentation 8
Device description 9
Technical data 10
Activities prior to starting work 12
Starting 13
Tamping 14
Taking out of operation 14
Maintenance overview 15
Maintenance work 16
Operating uids and ll levels 20
Troubleshooting 20
Storage 21
Contact addresses 23

4 SRV 650
Introduction
This operating and maintenance manual is designed to facilitate familiarization with your tamper, and
enable you to maintain the tamper and use it in accordance with the proper application possibilities.
When complying with the instructions in the operating and maintenance manual you help avoid
hazards, reduce repair and downtime costs, and increase the reliability and service life of your
tamper.
This operating and maintenance manual must always be available at the implementation site of the
tamper.
If necessary you can obtain additional information from your authorized WEBER dealer, or you can
obtain information from one of the contact addresses on the last page.
You can obtain information on the assembled Robin-Subaru gasoline engine and nd a spare-part list
for it at www.robin-europe.de
The valid conformity declaration is enclosed with every machine delivery.

SRV 650 5
Safety guidelines
General
All safety instructions must be read and complied with, non-compliance results in
- Danger to life and limb of the user
- Impairments to the machine or other property.
In addition to the operating manual, the accident-prevention regulations in the country where the
appliance is used must be complied with.
Intended use
The tamper should only be used in technically faultless condition, as intended, in a safety-conscious
and hazard-conscious manner, in compliance with the instructions in the operating manual.
Malfunctions that impair safety must be eliminated without delay.
The SRV 650 tamper is designed exclusively for compacting
- Sand
- Gravel
- Crushed rock
- Semi-cohesive mixed material
Any other use of the tamper is considered to be improper use for which the owner shall be
exclusively responsible. All liability is rejected if damage occurs due to non-compliance with this
provision. This risk is borne solely by the user.
Easily foreseeable misuse
Any use for which the machine is not intended.
Operating
Tampers should only be operated by suitable personnel of at least 18 years of age. Operators must
be instructed in how to guide the tamper by the owner or by owner’s assigned personnel.
The machine operator must comply with trafc regulations. If instructions that affect safety are given
by third parties, then the operator must be authorized to reject these instructions.
Protective equipment
Unauthorized persons are forbidden from being in the area of the tamper during the compacting
process.
Protective equipment includes:
Hearing protection
Hard hat
Safety shoes
This machine is capable of exceeding the permissible sound level of 80 dB(A). The owner might also
face additional dangers when using the machine. Precautionary action must, therefore, be taken.
Protective gloves

6 SRV 650
Prior to maintenance and repair work
Only use original Weber spare parts for maintenance or repair work to ensure reliable and safe
operation.
For repair, maintenance, or inspection work the engine of the tamper must be safeguarded against
unintentional starting.
All pressurized lines, particularly hydraulic lines and lines of the injection system of the drive motor
must be depressurized before performing maintenance or repair tasks.
For maintenance and repair tasks the tamper must be placed on a level and stable substrate and
must be secured from rolling off or tipping over.
Heavy components and assemblies must be secured to and lifted by hoisting machines that can
bear their weight when they are replaced. Ensure that no hazard is caused by raising components or
assemblies.
Do not position yourself or work under suspended loads.
Operation under difcult conditions
Never inhale the exhaust gas; it contains carbon monoxide, a colorless and odorless gas that
is extremely hazardous, which, if inhaled even briey, can cause unconsciousness and death.
Therefore, never operate the engines in enclosed areas or in areas that are poorly ventilated
(tunnels, caves, etc.). Exercise particular caution when operating the engine in the vicinity of
people and livestock.
Adjusting tasks, maintenance tasks, and inspection tasks must be carried out on schedule as
specied in this operating and maintenance manual. These activities should only be executed by
trained personnel.
Operation
Prior to starting work the owner of the tamper must be familiar with the work environment. The
working environment includes obstacles in the work and trafc area, the bearing capacity of the
ground, as well as the necessary safeguarding of the construction site in the area adjacent to public
trafc; and it also includes compliance with trafc regulations.
The tamper should only be operated when the protective xtures are mounted. The protective xtures
must all be in functional condition.
At least once per shift the tamper must be checked for apparent defects. If there are apparent defects
then operation of the tamper must be stopped immediately and the responsible person must be
informed. Prior to restarting, tamper malfunctions that have occurred must be corrected.
If lubricating oils and fuel come into contact with skin, they can cause skin cancer. Upon contact
with the skin, clean affected skin with suitable cleaning agent without delay.

SRV 650 7
Inspection
Tampers must be inspected in accordance with appropriate implementation conditions and operating
conditions, as needed; however an inspection to ensure operationally safe status must be performed
by an expert at least once a year. The results of the inspection must be recorded in writing and must
be stored at least until the next inspection.
Cleaning work
Prior to cleaning the tamper with a high-pressure cleaner, protect all accessible energized switches,
cable connections, etc. against water penetration by masking them off.
Cleaning tasks should only be executed in areas that are suitable and have been approved for this
purpose (oil separator amongst others).
Disposal
All operating uids and auxiliary materials must be disposed of in an environmentally-compatible
manner in accordance with country-specic regulations.
Warning against irritants or materials hazardous to health
Warning against a hazardous place
Warning against a suspended load
Wear ear protection
General regulation
Environmental protection
Important information for operating and maintenance personnel is marked by pictograms.
Hard hat
Safety shoes
Protective gloves

8 SRV 650
Graphic presentation
1
23
4
5
6
7
1 Fuel tank 6 Tamping system
2 Gas lever 7 Tamping foot
3 Hand guide bracket 8 Main lter
4 Engine 9 Secondary air lter
5 Transport roller 10 Handle
11 Hearing protection (sticker)
Total overview SRV 650
8
10
9
11

SRV 650 9
Device description
The series SRV 650 tamper is used for road-building, canal construction, pipe laying and
landscaping compaction tasks.
Drive
The tamper is powered by an air-cooled Subaru-Robin gasoline engine.
Force is transmitted via the centrifugal clutch directly to the tamping system. The compaction work
is performed by the tamping foot.
Operation
Start the Subaru-Robin gasoline engine with the attached reversing starter.
After starting the stamping system starts to vibrate via the centrifugal clutch which is attached to the
engine. Use the gas lever to vary the engine speed between idle speed and full-throttle speed.
For easier transport the tamper can be pushed onto or into a means of transport with the help of the
transport roller.
The engine is protected by a double lter system consisting of an oversized main air lter and an
additional air lter.

10 SRV 650
Technical data
SRV Black-Edition
Weight
Operating weight CECE in kg 70
Dimensions
Overall length (in mm) 740
Overall width (in mm) 365
Height (in mm) 1035
Tamping foot width (in mm) 280
Impact rate (/min) 670
Stroke (in mm) 77,2
Drive
Engine manufacturer Subaru
Type ER 12
Performance at operating speed in accordance with
ISO 3046-1 (kW) 2,7
Combustion process 4-stroke gasoline
Operating speed (1/min) 3900
Fuel Gasoline
unleaded
SRV Black-Edition
Noise emissions in accordance with 2000/14/EC
Sound pressure level LPA
ascertained in accordance with EN 500, in dB (A) 98
Sound pressure level LWA
ascertained in accordance with EN ISO 3744 and EN 500,
in dB (A) 108
Vibration values
Root-mean-square acceleration value for hand-arm
vibration ascertained in accordance with EN 500 in m/s² 10
In accordance with directive 2006/42/EC,
complying with the vibration values is the owner‘s
responsibility.

SRV 650 11
1 Description 2 Type
.................................................... ...................................................
3 Serial number 4 Year of manufacture
.................................................... ....................................................
5 Weight 6 Rated power kW
2
1
................................................... .....................................................
3 4
56

12 SRV 650
Transport
Fit the crane hook into the lifting ring (1) and lift the machine
onto the desired means of transport.
Loading with crane
1
Open and remove the gas cap (1), check the level, if
necessary top off to the lower edge of the ller neck with
clean fuel in accordance with the specication.
The correct oil level is between the min. and max. marks.
Check the engine oil level
Pull the oil dip stick (1) out of the crankcase.
Check the fuel level
1
Max.
Min.
1
Only use lifting machines with a minimum bearing ca-
pacity of 100 kg.
Do not step under suspended loads.
Activities prior to starting work
When transporting the tamper on a vehicle, secure it
with suitable restraints.
Carefully wipe up spilled fuel.
If lubricating oils and fuel come into contact with skin,
they can cause skin cancer. Upon contact with the skin,
clean affected skin with suitable cleaning agent without
delay.
For work at the fuel system, have a suitable re-extin-
guishing agent at the ready.
Fire, naked light, and smoking is forbidden!

SRV 650 13
Starting
1
2
After horizontal transport: Bring tamper into a vertical
position and wait several minutes until the engine oil
has collected in the lower area of the crankcase.
Open the fuel cock (1).
After the engine has warmed up, slide the choke lever
to the left (open).
Bring the gas lever into full-throttle lock-in position.
1
Slowly tighten the handle (1) of the reversing starter (2) until
resistance is noticeable.
Allow the handle (1) to glide back into the initial position, and
then forcefully and completely pull it through with both hands.
Allow the engine to warm up for a few minutes.
When starting in enclosed spaces ensure adequate ven-
tilation - danger of suffocation.
Never use any starter spray.
1
Push the choke lever (1) to the right (close).

14 SRV 650
Shutting down
To shut off the engine push the gas lever back
beyond the idle lock-in setting
Tamping
1
1
Close the fuel cock (1).
Compacting is only permissible at full throttle speed as
there is an increase level of wear in the slip range of the
centrifugal clutch.
At obstructions (walls, pits, etc.) ensure that no one can
be caught between the machine and the obstruction; or
ensure that the machine does not slip into the pit.
Do not switch off the engine under full load; let engine
run idle for a few minutes.
Only run machine within reach of the manual guidance
rod (1).
Unauthorized persons are forbidden from being in the
area of the tamper during the compacting process.
During breaks — even if they are short — the machine
must be shut down.
Parked devices that represent an obstacle must be
safeguarded against conspicuously.
Bring the gas lever into the lock-in position /
.
Bring the gas lever to the „min.“ (1) lock-in position.

SRV 650 15
Maintenance overview
The regulations of the engine manufacturer must be complied with in addition to
the above maintenance overview!
Work must be carried out using regulation tools and the operating and maintenance
manual must be complied with for all work.
All maintenance work: Select a collection vessel that is large enough to prevent oil from
spilling onto the ground. Dispose of waste oil in an environmentally friendly manner (re-
gulation on waste oils).
Dispose of oils, greases, cloths soaked in oil, and replaced parts with oil on them in an
environmentally friendly manner.
If lubricating oils and fuel come into contact with skin, they can cause skin cancer. Upon
contact with the skin, clean affected skin with suitable cleaning agent without delay.
If accessible during maintenance, check the condition and stability of all screws.
Maintenance interval Maintenance
point Maintenance activity
After the rst 10
operating hours Engine - Change engine oil
-Re-tighten all accessible threaded
connections
Every 50 operating hours/
every 6 months Main air lter -Clean air lter insert, check for damage, replace if necessary
Engine - Change engine oil
-Clean the engine oil lter
-Change the fuel lter
Every 150 operating
hours/every year Tamping system - Change oil

16 SRV 650
Change engine oil
Remove oil dip stick.
Open the drain plug (1) of the engine and drain oil.
1
Danger of scalding due to hot oil.
Check the oil ll level with the oil dip stick again.
Maintenance work
Screw in the oil drain plug (1) with new seal and top off with
oil as specied.
Only drain engine oil when at operating temperature.
When working in the area of the engine compartment
there is a danger of getting burnt! Max.
Min.
Clean oil screen
Remove the protection (1). 1
1
Drain oil as described above.
Unscrew the screw (1) including the attached oil screen
from the crankcase.
Use white gas to clean the oil screen before reinstalling it in
the crankcase.
Danger of scalding due to hot oil.
Check the oil ll level with the oil dip stick.
Only drain engine oil when at operating temperature.
When working in the area of the engine compartment
there is a danger of getting burnt!

SRV 650 17
Clean/change main air lter cartridge
Unscrew the air lter cover (1).
Remove the air lter insert (1) and the air lter eece (2)
from the air lter enclosure or remove air lter cover.
Clean air lter insert and air lter eece as specied by
the engine manufacturer if there is damage or if they are
extremely dirty.
1
2
1
Dispose of oils, greases, cloths soaked in oil, and
replaced parts with oil on them in an environmentally
friendly manner.
If lubricating oils and fuel come into contact with skin,
they can cause skin cancer. Upon contact with the
skin, clean affected skin with suitable cleaning agent
without delay.
Clean/change secondary air lter cartridge
Remove the protection (1).
Remove the air lter cover (1).
Remove the air lter insert (2) and the air lter eece from
the air lter enclosure or remove air lter cover.
Clean air lter insert and air lter eece as specied by
the engine manufacturer, if there is damage or or extreme
fouling.
1
1
2

18 SRV 650
1
0.6 - 0.7 mm
1
Adjust/replace the spark plug
Pull off the spark plug connector (1) and unscrew spark plug.
Clean the electrode (1) of the spark plug.
Measure the electrode air gap (1), the gab should be 0.6 - 0.7
mm.
Correct the electrode air gap or replace the spark plug if
necessary.
Only use spark plugs with the correct thermal value.
This work may only be carried out when the engine is cold.
1
2
Change the fuel line lter
Pull the fuel line (2) off the fuel lter (1) on both sides.
Replace the lter with a new lter element.
1
Change the fuel lter
Pull the fuel line (1) off the fuel cock (2).
12
Unscrew the fuel cock, including fuel lter (1) out of the fuel
tank.
Clean the fuel lter
Replace fuel lter if damaged.
For work at the fuel system, have a suitable re-extin-
guishing agent at the ready.
Fire, naked light, and smoking is forbidden!

SRV 650 19
0.6 - 0.7 mm
When mounting the new tamping foot the nuts (1) must
be tightened with a torque of 35 Nm.
Change the oil in the tamping system
Unscrew the screw plug (1) from the ll opening.
Tilt the tamper forward slightly and let the old oil drain into a
suitable collection container. Tilt the tamper back and ll oil in
as specied.
Clean the screw plug and screw it into the ll opening.
Select a collection vessel that is large enough to prevent
oil from spilling on the ground. Dispose of waste oil in an
environmentally friendly manner (regulation onwaste oils).
Change the tamping foot
Unscrew the 4 nuts (1).
Lift the tamping foot (2) off of the tamper and attach
a new tamping foot.
Mount the fastening nuts of the tamping foot using the
plate springs as shown in the adjacent illustration.
1
1
2
Mounting arrangement
of the plate springs
Dispose of oils, oil-soaked cloths, and parts
replaced and smeared with oil in an environmentally fri-
endly manner.

20 SRV 650
Troubleshooting
Operating uids and ll levels
Assembly Operating material
Summer Winter SRV
Quality Black-Edition
Engine
Engine oil SAE 10 W 40 0.3 L
Fuel tank
Gasoline Unleaded gasoline 3.0 L
Tamper lower part Hydraulic oil HVLP 68 1.0 L
Fault Possible cause Remedy
Tamper does not
start Operating error Execute the start process as prescribed
Lack of fuel Check the fuel level
Air lter fouled Clean/change air lter
Fuel lter fouled Change the fuel lter
Spark plug fouled Clean, adjust, replace the
spark plug
Oil level too low Top off with oil
Engine runs but it
does not reach full
speed
The fuel line is incorrectly
mounted
Check the mounting of the
fuel line
or engine runs Air lter fouled Clean/change air lter
but stops after Fuel lter fouled Change the fuel lter
a short time Spark plug fouled Clean, adjust, replace the
spark plug
Fuel cock closed Open fuel cock
Engine runs at
full rpm, tamper
does not tamp or
tamps inadequately
Unclean
compaction pattern
Centrifugal clutch is
defective Repair
Tamping foot is worn Change the tamping foot