Weber Ridgeline U-DS6000P User manual

Assembly Instructions
U-DS6000P
IMPORTANT
If you have difficulty assembling your U-DS6000P Ridgeline Table
or need customer service assistance. Please call:
Martin Universal Design, Inc. Customer Service Hot Line at 1-313-895-0700.
If you need additional parts, it is not necessary to contact your dealer,
our Customer Service Rep. will forward them to you immediately.
Martin Universal Design, Inc. • Detroit, MI 48208 USA
Tel: [phone] • E-mail: [email protected]
www.MartinUniversalDesign.com
Since 1853 November 09, RPI
Ridgeline

Hardware Parts List
Since 1853
November 09, RPI
A
2PCS
D
2PCS
G
2PCS
K
2PCS
B
4PCS
E
1PC
H
PCS
C
2PCS
F
2PCS
I
4PCS
L
4PCS
M
2PCS
O
1PC
P
2PCS
S
1PC
T
1PC
J
12PCS
N
2PCS
Q
2PCS
R
1PC
Side Support Floor Leveler Panel
Ridgeline
Top Tilt Mechanism
Height Adj. Tube w/ hole
4x14mm Screw
Knob 6x12mm Bolt Small Washer Large Washer
8x50mm Bolt Nut Pencil Edge 4x12mm Screw
Metal Guide Wrench #6 Hex Wrench #8 Hex Wrench
Height Adj. Tube 14

Assembly
Since 1853
STEP 1
Begin assembly of the Ridgeline table by taking
the side support (part A) and attaching the
oor levelers (part B) to the side supports.
See Fig 1
FIG 1
STEP 2
Continue by attaching the panel (part C)
to (part A) the side support, using 6 each
M6x12mm bolts (part J).
See Fig 2
FIG 2
NOTE:
We reccommend the
The Assembly of this table to be
performed with two adult people.
A
B
B
A
B
B
Jx6
C
STEP 3
Attach the second panel (part C) to (part A)
by using 6 each M6x12mm bolts (part J).
See Fig 3
FIG 3 Jx6
C
Ridgeline

Assembly
Since 1853
STEP 4
Attaching Height Adjustment Tubes.
To attach the height adjustment tubes
(part D + part F), use 4 each (part I) knob.
Leave a 12” gap from the top of the
side supports, and secure the tubes in place
by tightening the tubes with the knobs.
See Fig 4
FIG 4 Dx2
Ix4
Fx2
Ridgeline
E
Hx8
E
OPX2
QX2
STEP 5A
Attach (part Q), metal guide, by using 6 each
4x14mm screws (part H).
See Fig 5
FIG 5
STEP 5B
See Fig 5
Attach (part O) pencil edge to your desired
position using 2 each 4x12mm screws (part P).
There are no pre-drilled holes for pencil edge.
Attach (part G), tilt mechanism, by using
8 each 4x14mm screws (part H).
See Fig 5
STEP 5C
GX2
HX8
PX2
HX6

Assembly
Since 1853
STEP 6
Attaching Tilt Mechanism to
Height Adjustment Tube.
To attach the tilt mechanism (part G) to the
height adjustment tube, you will need the
following parts 1 each (part M) 8x50mm bolt,
2 each (part L) washer, 1 each (part K) washer,
1 each (part N) nut. Follow the diagram in
Figure 6 to attach the parts in the correct
order. See Fig 6
FIG 6
KLM
G
NL
D
Ridgeline
Attach Base to Top