Weber Captor 4115.30 sm 4 User manual

www.captor.de
Technical data subject to alteration! Rev. AJ 21.03.18
Sensors GmbH
Sensors Ltd.
Sensors LLC.
Strohdeich 32
66 Eastbourne Road, Southport
4462 Bretton Court, Building 1, Suite 7
DE-25377 Kollmar
Merseyside PR8 4DU, UK
Acworth, Georgia 30101, USA
Tel.: [phone] - 591· Fax: - 593
Tel.: +44 (1704) - 551684 · Fax: - 551297
Tel.: [phone] - 6630 · Fax: - 592 6640
[email protected]
[email protected]
[email protected]
Operation`s Manual
flow-captor
4115.30 sm x

www.captor.de
Technical data subject to alteration! Rev. AJ 21.03.18
Sensors GmbH
Sensors Ltd.
Sensors LLC.
Strohdeich 32
66 Eastbourne Road, Southport
4462 Bretton Court, Building 1, Suite 7
DE-25377 Kollmar
Merseyside PR8 4DU, UK
Acworth, Georgia 30101, USA
Tel.: [phone] - 591· Fax: - 593
Tel.: +44 (1704) - 551684 · Fax: - 551297
Tel.: [phone] - 6630 · Fax: - 592 6640
[email protected]
[email protected]
[email protected]
flow - captor
Type 4115.30 sm
Installation and Adjustment Instructions
Please read carefully: No liability can be accepted for damage caused by
improper use of the captor.
Before any handlings „Safety Instructions“ must be fully read!
1.0 Items delivered
1.1 flow-captor smart meter type 4115.30 sm
consisting of:
1.1.1 Sensor unit
1.1. Sensor fitting DIN ISO 228 G 1-½ “
complete with all sensor unit
mounting parts, see at 4.0 parts list
alt.
1.1.3 Sensor fitting 1-½ in. NPT
complete with all sensor unit
mounting parts, see at 4.0 parts list
1.2 Screwdriver for adjustment
2.0 Installation Instructions
2.1 Installation depth: 1/7x ID pipe sizes from 1,5“ to 24“
2.2 Orientation to flow: see drawing “Installation“
2.3 Fitting position: preferably in ascending pipes or in
horizontal pipes with flow-captor in horizontal position.
For optimal flow, straight pipe should be min. 7 x ID before,
and 5 x ID behind the flow-captor.
2.4 Mounting:
Screw in flow-captor smart meter into the fitting on the pipe
side and fix it at the correct insertion depth of 1/7 x ID (see
drawing no. K704315A)
2.5 Initial operation:
Connect flow-captor to 24 VDC according to connection
diagram and wait approx. 2 min. before starting any
measurement.
The flow-captor smart meter has been calibrated to the
specified type related flow rate (standard: medium water)
4115.30 sm 3: 0 to 1.0 m/s
4115.30 sm 4: 0 to 2.0 m/s
4115.30 sm 5: 0 to 3.0 m/s
4115.30 sm 6: 0 to 4.0 m/s
At customers plant signal may vary dependent on individual
mounting and medium conditions. If re-adjustment is re-
quired,
please refer to point 3.
Installation
Potentiometer, 18 turn, endless
Dimensions:
see drawing-no. K704315A
Connection Diagram

www.captor.de
Technical data subject to alteration! Rev. AJ 21.03.18
Sensors GmbH
Sensors Ltd.
Sensors LLC.
Strohdeich 32
66 Eastbourne Road, Southport
4462 Bretton Court, Building 1, Suite 7
DE-25377 Kollmar
Merseyside PR8 4DU, UK
Acworth, Georgia 30101, USA
Tel.: [phone] - 591· Fax: - 593
Tel.: +44 (1704) - 551684 · Fax: - 551297
Tel.: [phone] - 6630 · Fax: - 592 6640
[email protected]
[email protected]
[email protected]
flow - captor
Type 4115.30 sm
Installation and Adjustment Instructions
Please read carefully: No liability can be accepted for damage caused by
improper use of the captor.
Before any handlings „Safety Instructions“ must be fully read!
3.0 Adjustment Procedure
3.1 Zero point adjustment in stationary medium (roughly):
Adjust zero point potentiometer after 2 min. so,
that Ia » 4 mA, i.e. at Ia > 4 mA turn pot. to the left,
at Ia < 4 mA turn pot. to the right.
3.2 Measuring range adjustment at max. flow: Measuring range:
adjustable from 0-20 cm/s to 0-200 cm/s (medium water).
Accelerate flow of the medium to a point, where the flow-captor
should give an output signal of 20 mA and wait min. 2 minutes.
Turn range pot. until Ia = 20 mA (to the left Ia will be bigger, to
the right Ia will be smaller).The color of the LED will change from
green ( Ia £ 20 mA) to red (exceeding measuring range).
3.3 Fine adjustment of zero point: After at least 3 minutes standstill
of flow turn zero point slightly so, that Ia is just 4 mA ( turning
direction as in 3.1) .
3.4 Repeat adjustment according to 3.2 and 3.3 until the zero point
( 4 mA ) and max. range setting ( 20 mA) remain constant.
Calculation of the standard height for
1/7 ID (insertion depth)
Hs = L1- W - (1/7 x ID)
Hs: standard height
L1:unit length (see drawing)
W: wall thickness of pipe
ID: inner pipe diameter
For example:
L1 = 143 mm
W= 5 mm
ID = 50.4 (2“)
Hs = 143 - 5 -(1/7 x 50.4)
= 143 - 5 - 7.0
» 131 mm

www.captor.de
Technical data subject to alteration! Rev. AJ 21.03.18
Sensors GmbH
Sensors Ltd.
Sensors LLC.
Strohdeich 32
66 Eastbourne Road, Southport
4462 Bretton Court, Building 1, Suite 7
DE-25377 Kollmar
Merseyside PR8 4DU, UK
Acworth, Georgia 30101, USA
Tel.: [phone] - 591· Fax: - 593
Tel.: +44 (1704) - 551684 · Fax: - 551297
Tel.: [phone] - 6630 · Fax: - 592 6640
[email protected]
[email protected]
[email protected]
flow - captor
Type 4115.30 sm
Installation and Adjustment Instructions
Please read carefully: No liability can be accepted for damage caused by
improper use of the captor.
Before any handlings „Safety Instructions“ must be fully read!
Pos. Description Quantity/pcs. Article No.
1 threaded rod, M6, L: 5“ (127 mm), stainless steel 1.4305 (303) 3 00028381
2 hex nut, M6 (DIN 934), stainless steel 1.4305 (303) 12 00281601
3 lock washer for M6 (DIN 6797-I 6,4-VA), stainless steel 1.4305 (303) 6 00028057
4 cap nut, M6 (DIN 1587), stainless steel 1.4305 (303) 3 00028201
5 O-ring, Viton Vi500, 24,5x2 2 00241191
6a fitting G 1- ½“ (BSP) (DIN ISO 228), stainless steel 1.4571, 316 Ti 1 004318931
alternativ:
6b fitting 1- ½“ NPT, stainless steel 1.4571, 316 Ti 1 00431893
4.0 Parts List